İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Bevel Pinion with a No. 6 Cutter, Filed at the Small End (Brown & Sharpe 1911)
Forge

Oluşturan

Forge

27. Ekim 2026NO
11
0
0
0
0

Bevel Pinion with a No. 6 Cutter, Filed at the Small End (Brown & Sharpe 1911)

The same 12-tooth, 8-pitch pinion as Brown & Sharpe's worked example, but cut the way their own shop did it: with a No. 6 cutter instead of the No. 8 they sell for it, cut to the right thickness at the large end, then filed well round at the small end. They did this only for a 12-tooth pinion running with a gear two or three times its size. Source: Brown & Sharpe, Practical Treatise on Gearing (1911), Fig. 23 example, Part I ch. IX–X, Part II ch. III and the set-over table p. 58. The blank sizes are our arithmetic with their rules; the steel and bore are ours. Picture: their Fig. 23.
İleri
1 day

Talimatlar

1

Work out and turn the blank

Pitch diameter 12 ÷ 8 = 1.500 in. Angle of edge 26° 34′ and angle of face 59° 11′ (Brown & Sharpe's figures for every 12 and 24 tooth pair). Diameter increment = cos 26° 34′ × 0.250 = 0.224 in, so turn the steel blank to 1.72 in outside diameter. Face ½ in long. Try both angles with a protractor against the end of the hub.

Bu adım için malzemeler:

Yumuşak çelik lamaYumuşak çelik lama1 length for one blank

Gerekli aletler:

Metal Torna TezgâhıMetal Torna Tezgâhı
Torna kesici kalemiTorna kesici kalemi
İletkiİletki
MikrometreMikrometre
2

Choose the cutter

Twice the back cone radius × 8 comes to about 13, which would call for a No. 8, but take a No. 6, 8-pitch bevel gear cutter (17 to 20 teeth), as Brown & Sharpe's own shop did for this pinion. Measure its thickness Tc at the pitch line, 0.145 in from its tip.

Gerekli aletler:

Konik dişli frezesiKonik dişli frezesi
Dişli diş kumpasıDişli diş kumpası
3

Set the head at 22° 18′

Apex distance = sec 26° 34′ × 1.5 = 1.677 in. Angle increment: tan = sin 26° 34′ ÷ 6, giving 4° 16′. Set the dividing head to the cutting angle 26° 34′ − 4° 16′ = 22° 18′ and index 12 spaces. Depth at the large end 0.270 in.

Gerekli aletler:

Freze TezgâhıFreze Tezgâhı
Bölme AparatıBölme Aparatı
Konik dişli frezesiKonik dişli frezesi
4

Set over and cut one side

Apex distance ÷ face = 3.35; we take the nearest column, 3¼, where a No. 6 cutter has the factor .318. Set-over = Tc ÷ 2 − .318 ÷ 8 = Tc ÷ 2 − 0.040 in. Set off centre by that amount, take up backlash, and cut round all 12 spaces.

Gerekli aletler:

Freze TezgâhıFreze Tezgâhı
Bölme AparatıBölme Aparatı
Konik dişli frezesiKonik dişli frezesi
5

Set over the other way and trim

Set over the same amount the other side, line the cutter up with the space at the small end, take a trial cut, and rotate toward the cutter until the tooth is right at the faces of the large end: 0.196 in at the pitch line (0.138 in at the small end). Check with the gear tooth vernier, then cut round.

Gerekli aletler:

Freze TezgâhıFreze Tezgâhı
Bölme AparatıBölme Aparatı
Konik dişli frezesiKonik dişli frezesi
Dişli diş kumpasıDişli diş kumpası
6

File the small ends

The No. 6 cuts the tooth sides with a longer curve than the No. 8, so expect considerable filing: round the teeth over at the small ends, without filing them thinner at the pitch line.

Gerekli aletler:

İnce eğeİnce eğe

Malzemeler

1

Gerekli Aletler

9

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...