İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER

Coasting Toboggan: Four Steamed Hardwood Boards Bent Over a Log Form (Boy Mechanic, 1919)
A. M. Parker's toboggan from The Boy Mechanic, Book 3 (1919), 7-1/2 ft long and 16 in wide: four 5/16 in hardwood boards steamed at one end and bent round a 12 in log on a simple form, held by notched cross cleats, the curl riveted and wired, and a rope run along the sides.
Orta
About 1 week (four days drying)
Talimatlar
1
1
His mill bill in centimetres
His mill bill in centimetres
Jupyter defteri yükleniyor…
2
2
Read The Boy Mechanic, Book 3
Read The Boy Mechanic, Book 3
"Essentials of a good toboggan, whether for coasting or use in transportation, are strength and lightness." Woods in order of merit: hickory, birch and oak (not quarter-sawed).
3
3
Prepare the boards and cleats
Prepare the boards and cleats
Choose four 5/16 by 4 in by 10 ft boards straight in grain and free from knots. Plane the running side and bevel the edges so that, together, they form a wide V joint half the depth of the boards. Notch the seven 1 by 1 in cross cleats on one side, 1 in from each end, for the side ropes.
Bu adım için malzemeler:
Sert Ağaç Tahtası4 adetGerekli aletler:
El rendesi
El Testeresi
Marangoz keskileri
Kurşun kalem
Şerit Metre4
4
Build the bending form
Build the bending form
Bore a gimlet hole through the centre of each 1 by 2 by 18 in piece and two more 4-1/4 in each side of it. Nail one 6 ft common board to each end of the 12 in by 18 in log block so their ends run parallel. With 3 in nails fix one bored cleat to the block between them, held out 1/2 in by a temporary spacer.
Bu adım için malzemeler:
Çam tahta2 adet
Çiviler1 adetGerekli aletler:
El Testeresi
El matkabı
Çekiç5
5
Steam and bend
Steam and bend
Steam about 3 ft of the board ends, or boil them in a tank. Clamp or nail the dry ends together edge to edge between two of the 1 by 2 in pieces, about 1/4 in apart. Push the steamed ends under the cleat on the block (its nails slip between the boards), bear down and nail on another bored cleat as far as the floor allows. Turn it over and bend the boards round the block, nailing on more cleats, until the clamped end lies between the 6 ft boards; hold it with a piece nailed across. The closer the cleats, the less risk of splitting.
Bu adım için malzemeler:
Çiviler1 adetGerekli aletler:
Büyük Tencere
Çekiç
Çubuklu işkence6
6
Fit the cleats and finish
Fit the cleats and finish
Dry at least four days on the form. Clamp the two 1/2 by 1 in pieces on each side of the bow ends, drill through and rivet them. Rivet a 1 by 1 in crossbar inside the bow at the extreme front and another under the end of the curl, and wire them together to hold the bend. Put the tail crossbar not nearer than 2-1/2 in from the board ends and space the rest evenly, notched side down. Trim, scrape and sandpaper the bottom, finish with oil, and run a 3/8 in rope through the notches under the cleat ends.
Bu adım için malzemeler:
Sert Ağaç Tahtası1 adet
Çelik perçinler1 adet
Demir tel1 adet
Bezir Yağı1 adet
Zımpara Kağıdı1 adet
Pamuk halat1 adetGerekli aletler:
El matkabı
Çekiç
El Testeresi
Çelik raspa
Yassı Ağızlı Pense7
7
Troubleshooting
Troubleshooting
Toboggan troubleshooting.
Flow
Loading...
8
8
History and honest limits
History and honest limits
From "Making a Coasting Toboggan" by A. M. Parker, in **The Boy Mechanic, Book 3**, Popular Mechanics, 1919 (Project Gutenberg 71856; checked on the archive.org scan boymechanic0003unse, pp. 11-13). The tools and metric figures are ours.
Malzemeler
8- 4 adetYer Tutucu
- 2 adetYer Tutucu
- 2 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
Gerekli Aletler
11- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- 1 vendor sell this, none ship to you yetYer Tutucu
- 1 vendor sell this, none ship to you yetYer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
Bu planla yapılan
İlgili Blueprint'ler
Bu blueprint'ler bilgi paylaşır — teknikler, malzemeler veya ilkeler
CC0 Kamu Malı
Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.
Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.


