İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Ice Boat: Crossed Timbers, Skate-Edged Runners, Bicycle-Fork Steering and a Gaff Sail (Boy Mechanic, 1915)
Woody

Oluşturan

Woody

13. Kasım 2026NO
7
0
0
0
0

Ice Boat: Crossed Timbers, Skate-Edged Runners, Bicycle-Fork Steering and a Gaff Sail (Boy Mechanic, 1915)

Robert K. Patterson's ice boat from The Boy Mechanic, Book 2 (1915): a 16 ft timber crossed by a 10-1/2 ft one and braced with wires, two front runners of band iron ground like a skate edge, and a rear steering runner clamped in a cut-down bicycle fork worked by a lever. His text and his drawing differ on the mast (about 12 ft against 14 ft); both are given.
İleri
About 1 week

Talimatlar

1

Text against drawing

Jupyter defteri yükleniyor…
2

Read The Boy Mechanic, Book 2

"In constructing the ice boat, use two poles, or timbers, one 16 ft. and the other 10-1/2 ft. long, crossed at a point 2-1/2 ft. from one end of the longer timber. The crossed pieces are firmly braced with wires, as shown."
3

Cross and brace the frame

Cross the 10-1/2 ft timber over the 16 ft one, 2-1/2 ft from its front end, and fasten them firmly. Brace them with wires as in the drawing: from the bow to points on the cross timber, and from the cross timber back along the long one. The drawing puts the wire points 6 in and 1 ft 6 in from each end of the cross timber.

Bu adım için malzemeler:

Ahşap sırıkAhşap sırık2 adet
Kare boyunlu yuvarlak başlı cıvataKare boyunlu yuvarlak başlı cıvata1 adet
Çelik telÇelik tel1 adet

Gerekli aletler:

El TesteresiEl Testeresi
Kol matkabı ve ucuKol matkabı ve ucu
Şerit MetreŞerit Metre
Kurşun kalemKurşun kalem
4

Make the front runners

Cut two band-iron strips 18 in long, 3 in wide and 1/8 in thick; grind one edge like the edge of a skate and round the ends. Bolt each to the side of a wood piece 18 in long, 6 in wide and 2 in thick, so the ground edge projects about 1 in. With a pole frame, bolt each runner block at right angles to a 12 in piece of wood shaped as drawn, the bolts running diagonally through its shouldered part; the pole end rests on this and is bolted down. With squared timbers, fasten the runners straight to them.

Bu adım için malzemeler:

Yumuşak Çelik LamaYumuşak Çelik Lama1 adet
Sert Ağaç TahtasıSert Ağaç Tahtası1 adet
Kare boyunlu yuvarlak başlı cıvataKare boyunlu yuvarlak başlı cıvata1 adet

Gerekli aletler:

Demir TesteresiDemir Testeresi
Taşlama motoruTaşlama motoru
Tezgah MengenesiTezgah Mengenesi
El matkabıEl matkabı
El TesteresiEl Testeresi
5

Make the steering runner

Fasten the rear runner between two pieces of wood so its edge projects, and clamp it in a bicycle fork cut down to leave about 3 in of the blades. Bore a hole through the rear end of the long timber for the fork head. Fit a lever (5 ft on the drawing) to the top of the fork head: bore a hole through the lever end at a slight angle to fit the head, slot the end, bore across the width of the handle and put in a bolt as a clamp.

Bu adım için malzemeler:

Yumuşak Çelik LamaYumuşak Çelik Lama1 adet
Sert Ağaç TahtasıSert Ağaç Tahtası1 adet
Bisiklet çatalıBisiklet çatalı1 adet
Kare boyunlu yuvarlak başlı cıvataKare boyunlu yuvarlak başlı cıvata1 adet
Yumuşak ağaç çıtaYumuşak ağaç çıta1 adet

Gerekli aletler:

Demir TesteresiDemir Testeresi
Taşlama motoruTaşlama motoru
Kol matkabı ve ucuKol matkabı ve ucu
El TesteresiEl Testeresi
Marangoz keskileriMarangoz keskileri
6

Step the mast and fit the seat

Cut a mortise in the long timber 15 in from the front end and set the mast in it; stay it with wires as drawn. His text says the mast should be about 12 ft; his drawing marks it 14 ft 0 in: choose one and keep the sail to suit. Fasten a board on two crosspieces mortised into the top of the long timber, as a seat for the driver (5 ft long on the drawing, ending 2 ft 3 in from the stern).

Bu adım için malzemeler:

Yumuşak ağaç çıtaYumuşak ağaç çıta1 adet
Çelik telÇelik tel1 adet
Çam tahtaÇam tahta1 adet
Ahşap vidalarAhşap vidalar1 adet

Gerekli aletler:

El TesteresiEl Testeresi
Marangoz keskileriMarangoz keskileri
El rendesiEl rendesi
Şerit MetreŞerit Metre
7

Make and rig the sail

Make the sail of any good material to his drawing: luff (along the mast) 9 ft 0 in, head 4 ft 8 in, foot 11 ft 0 in, leech 12 ft 6 in. Hang the main boom, 11-1/2 ft long, and the upper spar on the mast "in the usual manner". The text also names a jib boom of about 6 ft, which the drawing does not show.

Bu adım için malzemeler:

Kanvas kumaşKanvas kumaş1 adet
Yumuşak ağaç çıtaYumuşak ağaç çıta1 adet
Pamuk halatPamuk halat1 adet

Gerekli aletler:

MakasMakas
El TesteresiEl Testeresi
Şerit MetreŞerit Metre
8

Troubleshooting

Ice boat troubleshooting.

Flow

Loading...
9

History and honest limits

From "An Ice Boat and Catamaran" by Robert K. Patterson, in **The Boy Mechanic, Book 2**, Popular Mechanics, 1915 (Project Gutenberg 44585; checked on the archive.org scan boymechanicbook200chic2, pp. 27-28). His text and drawing differ on the mast (about 12 ft against 14 ft 0 in) and on the jib boom, which is in the text only; both are stated, not resolved. He gives no timber sections, wire size or sail cloth: those choices are ours, as are the tools and metric figures. The summer catamaran conversion is not made here.

Malzemeler

11

Gerekli Aletler

11

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...