İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Jointed Fishing Rods: Two- and Three-Piece Casting, Trout and Bass Fly, Salt-Water and Tarpon Rods (Boy Mechanic, 1915)
Woody

Oluşturan

Woody

13. Kasım 2026NO
7
0
0
0
0

Jointed Fishing Rods: Two- and Three-Piece Casting, Trout and Bass Fly, Salt-Water and Tarpon Rods (Boy Mechanic, 1915)

Part II of Stillman Taylor's rod-making series (The Boy Mechanic, Book 2, 1915): once the one-piece casting rod is mastered, the same planing, grasp and finishing methods make jointed rods. He gives full caliper tables and fitting lists for six rods; choose one in the notebook. Sections join with welted, shouldered ferrules, and every rod gets two tips "in view of a possible breakage".
İleri
About 2-3 weeks (glue and varnish drying)

Talimatlar

1

His caliper tables

Jupyter defteri yükleniyor…
2

Read The Boy Mechanic, Book 2

"While the action of the one-piece rod is undeniably better than when the rod is made in two or three pieces, it is less compact to carry." He warns that "the more joints incorporated in a rod, the less satisfactory it will be from an angling standpoint", since ferrules cannot follow the rod's curve.
3

Choose the rod and get the stock

Pick a rod from the notebook. Stock (dagame or greenheart): two-piece casting -- butt 5/8 in x 3 ft, two tips 3/8 in x 3 ft; three-piece casting -- all 2 ft, butt 5/8 in, joint and tips 3/8 in; trout or bass fly -- butt 5/8 in x 4 ft, joint and tips 3/8 in x 4 ft; salt-water -- both 4 ft, butt 3/4 in, tip 1/2 in; tarpon -- one piece 1 in x 6-1/2 ft.

Bu adım için malzemeler:

Dagame ağacıDagame ağacı4 adet

Gerekli aletler:

El TesteresiEl Testeresi
Şerit MetreŞerit Metre
4

Plane each section to its table

Plane, round and scrape each section exactly as for the one-piece rod, calipering at every station in the table. Two-piece casting rod: he first suggests a butt of about 23 in and a 32-1/2 in tip to fit a 35 in rod case, then specifies a 6-1/2 oz rod with a 32-1/2 in butt (15/32 in at the grasp to 19/64 in at the ferrule) and a 33 in tip (17/64 in to 7/64 in), equal when ferrule and top are on. Make two tips for each rod.

Bu adım için malzemeler:

Zımpara KağıdıZımpara Kağıdı1 adet

Gerekli aletler:

El rendesiEl rendesi
Blok rendeBlok rende
Çelik raspaÇelik raspa
Eğeler (El Eğesi)Eğeler (El Eğesi)
KumpasKumpas
5

Fit the ferrules

Fit a welted, shouldered ferrule at each joint, sized from his list: 17/64 in for the two-piece casting rod; 21/64 in and 15/64 in for the three-piece; 9/32 in and 11/64 in for the fly rods; 7/16 in for the salt-water rod; a 3/4 in male ferrule on the tarpon butt. The tip ferrule comes with two closed-end centres, one for each tip. Cement them on with ferrule cement; serrated (toothed) ferrule ends are wound with silk for strength.

Bu adım için malzemeler:

Kamış bağlantı yüksüğüKamış bağlantı yüksüğü2 adet
Yüksük yapıştırıcısıYüksük yapıştırıcısı1 adet
Kamış sarma ipeğiKamış sarma ipeği1 adet

Gerekli aletler:

Eğeler (El Eğesi)Eğeler (El Eğesi)
Propan PürmüzPropan Pürmüz
KumpasKumpas
6

Build the grasp and reel seat

Build the cork grasp and reel seat as for the one-piece rod: 3/4 in reel seat with straight hood for the casting rods (fly-rod type with butt cap on the fly rods, 9 in or 9-1/2 in of cork above it), 7/8 in on the salt-water rod with an 18 in double grasp, 1 in on the tarpon rod. Use a 1 in butt cap (1-1/8 in on the tarpon rod) and a taper (winding check) of the small-end size in his list. For an independent butt, fit the ferrule straight on a rounded dagame core so the seated ferrule does not touch the wood, cement and rivet it, fit a soft-pine sleeve over core and ferrule, glue it on, cement and rivet the reel seat, then glue on the corks and cut the core flush.

Bu adım için malzemeler:

Mantar halkalarMantar halkalar24 adet
Hayvansal tutkalHayvansal tutkal1 adet
Çam tahtaÇam tahta1 adet
Makine yuvasıMakine yuvası1 adet
Kamış dip kapağıKamış dip kapağı1 adet
Tutamak bitiş halkasıTutamak bitiş halkası1 adet
Yüksük yapıştırıcısıYüksük yapıştırıcısı1 adet
Bakır perçinlerBakır perçinler1 adet

Gerekli aletler:

Maket BıçağıMaket Bıçağı
El matkabıEl matkabı
Blok rendeBlok rende
Propan PürmüzPropan Pürmüz
ÇekiçÇekiç
7

Mount the guides and tops

Casting rods: two 1/2 in narrow agate guides, two No. 1 one-ring casting guides and two 3/32 in offset agate tops. Fly rods: two No. 4 snake guides on the butt joint, three No. 3 on the middle joint, three No. 2 on each tip, and two No. 7 agate angle fly tops of the wind-on kind. Salt-water rod: a 10/32 in stirrup-tube agate top and two No. 3 bell guides. Tarpon rod: two No. 11 wide raised agate guides, two No. 1 trumpet guides and a 3/8 in agate stirrup top; whip its guides on double, the first set 10 in from the top, the second 26 in from the reel. Whip with 00 silk (00 or 0 on the three-piece rod, size A on the salt-water and tarpon rods), using the invisible knot.

Bu adım için malzemeler:

Kamış halkasıKamış halkası8 adet
Kamış uç halkasıKamış uç halkası2 adet
Kamış sarma ipeğiKamış sarma ipeği1 adet
BalmumuBalmumu1 adet

Gerekli aletler:

Eğeler (El Eğesi)Eğeler (El Eğesi)
Maket BıçağıMaket Bıçağı
8

Shellac and varnish

Shellac the windings and varnish the rod with coach varnish as for the one-piece rod: thin coats, warm, three days between coats.

Bu adım için malzemeler:

Gomalak vernikGomalak vernik1 adet
Araba verniğiAraba verniği3 adet

Gerekli aletler:

Geniş boya fırçasıGeniş boya fırçası
9

Troubleshooting

Jointed rod troubleshooting.

Flow

Loading...
10

History and honest limits

From "Fishing-Rod Making and Angling, Part II" by Stillman Taylor, in **The Boy Mechanic, Book 2**, Popular Mechanics, 1915 (Project Gutenberg 44585; checked on the archive.org scan boymechanicbook200chic2, pp. 69-72). Two points are given as he wrote them: the two-piece casting rod's butt is about 23 in in one sentence and 32-1/2 in in the next; the three-piece rod's stock is "2 ft. long" while its finished sections are 21-1/2, 21-3/4 and 21 in. Guide counts in the list are for the fly rods, the largest set. The tools and metric figures are ours.

Malzemeler

17

Gerekli Aletler

12

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...