İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Canteen From Two Pie Plates: Rims Soldered Together, a Screw-Cap Neck in the Edge (Boy Mechanic, 1919)
Tinny

Oluşturan

Tinny

13. Kasım 2026US
9
0
0
0
0

Canteen From Two Pie Plates: Rims Soldered Together, a Screw-Cap Neck in the Edge (Boy Mechanic, 1919)

A canteen "for the camper or hiker", sent to The Boy Mechanic (1919) by J. R. Townsend of Itasca, Texas: two nickel-plated pie plates soldered rim to rim, the screw-capped neck of a metal-polish can soldered over an opening in the edge, and two wire loops for the snap hooks of a shoulder strap. The book gives no sizes: the plates set the size.
Başlangıç
About 2 hours

Talimatlar

1

Read The Boy Mechanic

"Two good-quality pie plates were soldered at their edges to form a water-tight container." (J. R. Townsend, Itasca, Texas.)
2

Solder the plates together

Take two good-quality nickel-plated pie plates of the same size. Clean the rims, set them face to face, and solder them together all round the edge so the joint is water-tight. Use lead-free solder: this holds drinking water (our choice; the book only says solder).

Bu adım için malzemeler:

Turta kalıbıTurta kalıbı2 adet
Kurşunsuz tesisat lehimiKurşunsuz tesisat lehimi1 adet
DekapanDekapan1 adet

Gerekli aletler:

Elektrikli HavyaElektrikli Havya
Metal EğeMetal Eğe
3

Cut the neck off the can

Take a small metal-polish can with a screw cap. As the book's drawing shows, cut off its sloping top with the threaded neck, and trim the cut edge.

Bu adım için malzemeler:

Teneke kutuTeneke kutu1 adet

Gerekli aletler:

Ağır iş metal makasıAğır iş metal makası
Metal EğeMetal Eğe
4

Cut the opening and fit the neck

Cut an opening in the edge of the canteen to suit the neck. Fit the neck carefully over it and solder it all round.

Bu adım için malzemeler:

Kurşunsuz tesisat lehimiKurşunsuz tesisat lehimi1 adet
DekapanDekapan1 adet

Gerekli aletler:

El matkabıEl matkabı
Metal EğeMetal Eğe
Elektrikli HavyaElektrikli Havya
5

Solder on the strap loops

Bend two short pieces of wire into loops and solder one at each side of the screw cap, as loops for the snap hooks of the shoulder strap.

Bu adım için malzemeler:

Demir telDemir tel1 adet
Kurşunsuz tesisat lehimiKurşunsuz tesisat lehimi1 adet
DekapanDekapan1 adet

Gerekli aletler:

Yassı Ağızlı PenseYassı Ağızlı Pense
Elektrikli HavyaElektrikli Havya
6

Fit the strap and test

Put a snap hook on each end of a shoulder strap and hook them into the loops. Fill the canteen with water, screw on the cap and check every joint for leaks (our test), then rinse it before use.

Bu adım için malzemeler:

Deri KayışDeri Kayış1 adet
Yaylı kancaYaylı kanca2 adet

Gerekli aletler:

Tatlı suTatlı su
7

Troubleshooting

Canteen troubleshooting.

Flow

Loading...
8

History and honest limits

From **The Boy Mechanic, Book 3**, edited by H. H. Windsor, Popular Mechanics, Chicago, 1919 (Project Gutenberg 71856), "How to Make a Canteen", sent in by J. R. Townsend of Itasca, Texas. The book gives no sizes and names no tools; the lead-free solder, the tools, the strap material and the leak test are ours.

Malzemeler

7

Gerekli Aletler

6

Bu planla yapılan

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...