İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER

Ski Sled: Two 10 ft Ash Ski Runners With a Rocker, Under a Three-Board Top (Boy Mechanic, 1919)
George J. Egelberg's ski sled from The Boy Mechanic, Book 3 (1919): "built low and wide so that it will not tip easily", on two 10 ft by 6 in ash runners boiled and bent like skis, set on knee blocks with a slight rocker, and topped with three 6 in boards.
Orta
About 2 days
Talimatlar
1
1
His sizes, and the rocker
His sizes, and the rocker
Jupyter defteri yükleniyor…
2
2
Read The Boy Mechanic, Book 3
Read The Boy Mechanic, Book 3
"The skis, or runners, are cut 10 ft. long and 6 in. wide, from 1-in. ash boards that are straight-grained."
3
3
Thin the bend
Thin the bend
Cut two runners 10 ft long and 6 in wide from straight-grained 1 in ash. Where the curve will be, plane about 1/4 in off the upper side, but not at the very tip, so the skis bend more easily.
Bu adım için malzemeler:
Sert Ağaç Tahtası2 adetGerekli aletler:
El Testeresi
El rendesi
Şerit Metre
Kurşun kalem4
4
Boil and bend
Boil and bend
If steaming is not handy, boil the skis with at least 1-1/2 ft of the points under water and the vessel covered so little steam escapes, for at least one hour. Take them out, put them side by side in the bending blocks at once and bend with slow, even pressure; weight the long ends and leave them 8 or 10 hours to dry. Sharpen the points after bending.
Bu adım için malzemeler:
Çam tahta1 adetGerekli aletler:
Büyük Tencere
Çubuklu işkence
El rendesi5
5
Set the blocks and top
Set the blocks and top
For a slight rocker, make the centre knee block 6 in high and the two end blocks 5-1/2 in. Run a 1/4 in flat-head bolt through the ski, the block and the cross strip, countersinking the heads in the running surface. Make the top of three 6 in boards fastened to the crosspieces, and brace the ski tips with a 2 in strip.
Bu adım için malzemeler:
Sert Ağaç Tahtası1 adet
Çam tahta3 adet
Kare boyunlu yuvarlak başlı cıvata6 adet
Düz Pul6 adet
Ahşap vidalar1 adetGerekli aletler:
El Testeresi
El matkabı
Havşa Ucu Seti
Çekiç6
6
Troubleshooting
Troubleshooting
Ski sled troubleshooting.
Flow
Loading...
7
7
History and honest limits
History and honest limits
From "A Ski Sled" by George J. Egelberg, in **The Boy Mechanic, Book 3**, Popular Mechanics, 1919 (Project Gutenberg 71856; checked on the archive.org scan boymechanic0003unse, p. 41). The bending-block shape and knee pieces come from his drawing. The tools and metric figures are ours.
Malzemeler
5- 2 adetYer Tutucu
- 3 adetYer Tutucu
- Yer Tutucu
- 6 adetYer Tutucu
- 1 adetYer Tutucu
Gerekli Aletler
9- Yer Tutucu
- Yer Tutucu
- 1 vendor sell this, none ship to you yetYer Tutucu
- 1 vendor sell this, none ship to you yetYer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
Bu planla yapılan
İlgili Blueprint'ler
Bu blueprint'ler bilgi paylaşır — teknikler, malzemeler veya ilkeler
CC0 Kamu Malı
Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.
Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.


