İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Clamp-On Countersink: Two Blocks Screwed Round Any Drill, Twin Cutters Countersink the Hole as It Is Bored (Brackin, 1903)
Forge

Oluşturan

Forge

13. Kasım 2026NO
11
0
0
0
0

Clamp-On Countersink: Two Blocks Screwed Round Any Drill, Twin Cutters Countersink the Hole as It Is Bored (Brackin, 1903)

George W. Brackin of Philadelphia received US 727,580, dated 12 May 1903, for a countersink that clamps onto a drill or auger bit. Two blocks are screwed together across the bit at any point along it. A twin cutter is screwed into an inclined seat in each block, its point reaching into the bit's flutes. As the bit bores, the cutters arrive and cut the cone for the screw head without taking the bit out. A slotted stop sets how deep it goes, so it gauges the hole too. We make three for 4, 5 and 6 mm drills. The patent gives no sizes; every size here is ours.
Orta
About 1 day

Talimatlar

1

Setting it on the bit

Jupyter defteri yükleniyor…
2

Read US 727,580

"From Figs. 2 and 3 it will be observed that the lower ends of the inclined cutters project slightly into the twists or helical channels of the drill, and this fact permits the cutters to enter the hole bored and then commence cutting away the edge of the hole as the tool is rotated."
3

Clamping blocks 2 and 3

For each attachment cut two blocks 40 x 12 x 10 mm from square bar. In each, 6 mm from one end drill a 4.5 mm plain hole and 6 mm from the other end drill 3.3 mm and tap M4, through the 12 mm face, so the two blocks screw together with the plain hole of one over the tapped hole of the other. Across the middle of each block's outer face file a seat 6 mm wide, sloping down and in at 45 degrees, and drill and tap M4 in it for the cutter's screw.

Bu adım için malzemeler:

Yumuşak çelik kare çubukYumuşak çelik kare çubuk1 adet

Gerekli aletler:

Demir TesteresiDemir Testeresi
Tezgah MengenesiTezgah Mengenesi
ÇizecekÇizecek
Nokta ZımbasıNokta Zımbası
Sütunlu MatkapSütunlu Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Kılavuz ve pafta takımıKılavuz ve pafta takımı
Kılavuz koluKılavuz kolu
Eğe TakımıEğe Takımı
İletkiİletki
Dijital Kumpas 6 İnçDijital Kumpas 6 İnç
4

Twin cutters 8 and 9

Cut four cutters 22 mm long from 3 x 6 mm carbon steel strip. Drill each 4.5 mm for its screw at the top, and grind the lower end to a point with a straight cutting edge 13 on its leading side and a rounded back 15, as his Fig. 4. Harden: heat to a cherry red, until a magnet no longer sticks, quench in water, rub bright, and draw to a light straw colour.

Bu adım için malzemeler:

Karbon çeliği şeritKarbon çeliği şerit1 adet

Gerekli aletler:

Demir TesteresiDemir Testeresi
Sütunlu MatkapSütunlu Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Taşlama motoruTaşlama motoru
Demirci OcağıDemirci Ocağı
Demirci MaşasıDemirci Maşası
Küçük MıknatısKüçük Mıknatıs
Su verme kovasıSu verme kovası
SuSu
Bileği TaşıBileği Taşı
Kaynak eldivenleriKaynak eldivenleri
Koruyucu gözlükKoruyucu gözlük
5

Stop 17 and assembly

Bend a strip of 3 mm flat bar into an L, its upright 30 mm long with a 4.5 mm slot 18 15 mm long, its foot 20 mm. Screw a cutter into each block's seat. Put the blocks either side of the drill, the stop's slot under one clamping screw, and screw them together until they grip the drill, the cutters' points just in the flutes and their edges leading as the drill turns.

Bu adım için malzemeler:

Yumuşak Çelik LamaYumuşak Çelik Lama1 adet
Makine vidalarıMakine vidaları4 adet

Gerekli aletler:

Demir TesteresiDemir Testeresi
Tezgah MengenesiTezgah Mengenesi
Sütunlu MatkapSütunlu Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Eğe TakımıEğe Takımı
Tornavida takımıTornavida takımı
6

Bore and countersink

Set the drill's point the hole's depth below the stop's foot and the cutters for the screw head's size (the notebook gives both). Drill into hardwood until the stop touches: the hole is at depth and its mouth countersunk. Check a screw sits flush.

Gerekli aletler:

Kablosuz MatkapKablosuz Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Sert Ağaç TahtasıSert Ağaç Tahtası
Dijital Kumpas 6 İnçDijital Kumpas 6 İnç
Koruyucu gözlükKoruyucu gözlük
7

Troubleshooting

Clamp-on countersink troubleshooting.

Flow

Loading...
8

History and honest limits

**George W. Brackin** of Philadelphia, US 727,580, dated 12 May 1903, filed 18 June 1902. He claimed "the rectangular clamping-blocks arranged parallel to each other, clamping-screws passing through the said blocks near their ends", each block "provided exteriorly at its middle point with a cutter-seat inclined downwardly and inwardly", and "duplicate and interchangeable cutters" screwed into them. His was for wood, with the note that the cutters could be hardened for metal; ours are hardened. He gives no sizes or angle; every size here is ours.

Malzemeler

4

Gerekli Aletler

23

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...