İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER

Ring-Disk Spiral-Pin Churn: Cream Forced Out Between Corrugated Rings, Then Drawn to the Middle by Spiral Pins
Daniel C. Brown of New York received US 26,880, dated 24 January 1860, for a churn. Cream poured into a hopper runs into the middle of a still disk at the bottom of a box, under a turning disk; their corrugated rings run between each other without touching, so the cream is flung outward and must climb over ring after ring. Above, the turning shaft carries pins set in two spirals that meet in the middle, drawing the butter there to be gathered.
The patent gives no sizes; every size here is ours.
Orta
About 2 days, plus printing
Talimatlar
1
1
Rings that never touch
Rings that never touch
Jupyter defteri yükleniyor…
2
2
Agitators passing between each other, two months before
Agitators passing between each other, two months before
Cornell's arms pass between those of a second shaft. Brown's rings run between the rings of a still disk.
3
3
Read US 26,880
Read US 26,880
"The milk or cream thus entering while the disk G is in rapid motion, it will be seen that (by the centrifugal force developed) the fluid will be forced outward, but, meeting the obstruction of the rings, will be checked—accumulate to some extent until forced to climb over and around them, successively advancing thus and being checked and being thereby subjected to the action of the corrugated surfaces upon each side of the rings"
4
4
Print the still disk F
Print the still disk F
A disk 236 mm across with three corrugated rings 8 mm thick and 12 tall at 40, 74 and 108 mm, a 21 mm bearing for G's journal, a 13 mm inlet beside it for the spout, and three feet. PETG, 0.2 mm layers, 40 % infill, 4 walls.
5
5
Print the turning disk G
Print the turning disk G
A disk 236 mm across with two corrugated rings at 57 and 91 mm, a 20 mm journal below and a hub above with a cross hole for the shaft's pin. PETG, 0.2 mm layers, 40 % infill, 4 walls.
6
6
Print the gear wheel
Print the gear wheel
Spur wheel, 48 teeth, module 3, 15 mm face, with a hub bored 20.6 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
7
7
Print the geared stud's pinion
Print the geared stud's pinion
Spur pinion, 16 teeth, module 3, 15 mm face, with a hub bored 20.6 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
8
8
Box A, hopper B and spout C
Box A, hopper B and spout C
From 20 mm hardwood make a box 300 x 300 mm and 450 mm deep inside with a lid bored 21 mm in its middle. Bore one side 13 mm, 10 mm above the floor in its middle. Bend a 12 mm stainless tube to run from outside, through that hole along the floor and up into F's inlet, seal it through the side, and fit a stainless funnel on its outer end as the hopper. Fill the box with water overnight so it swells tight, then empty it.
Bu adım için malzemeler:
Sert Ağaç Tahtası3 adet
Ahşap Tutkalı1 adet
Ahşap vidalar30 adet
Paslanmaz çelik boru1 adet
Paslanmaz çelik huni1 adetGerekli aletler:
Daire testere tezgâhı
El Testeresi
Kablosuz Matkap
Matkap Ucu Takımı
Yassı matkap ucu takımı
Demir Testeresi
Çubuklu işkence
Şerit Metre
Su9
9
Disks, shaft D and pins b
Disks, shaft D and pins b
Stand F on its feet in the middle of the floor over the spout. Plane a hardwood shaft to a hexagon 40 mm across the flats and 393 mm long, with a 19 mm square socket 30 mm deep in its top, and pin its foot in G's hub. Bore twelve 16 mm holes through it from 35 to 332 mm above its foot, 27 mm apart, and glue in hardwood pins reaching 135 mm from the middle: the lower six turning 60 degrees each from the foot upward, the upper six the same from the top downward, so the two spirals meet at the middle. Set G's journal in F's bearing.
Bu adım için malzemeler:
Sert Ağaç Tahtası1 adet
Sert ağaç kavelalar1 adet
Ahşap Tutkalı1 adet
Kopilya1 adet
PETG filament1 adetGerekli aletler:
FDM 3B yazıcı
Ahşap torna tezgâhı
Daire testere tezgâhı
Zıvana yuvası kalemi
Ahşap Tokmak
Kablosuz Matkap
Matkap Ucu Takımı
Zımpara Kağıdı10
10
Geared stud and crank E
Geared stud and crank E
Pass a 20 mm stainless stud through the lid, square at its foot to drop into the shaft's socket, with the pinion pinned on top. Fix a second stud in the lid 96 mm away carrying the gear wheel, meshing, with a crank and handle on it. Lift the lid to free the shaft and disks for cleaning.
Bu adım için malzemeler:
Paslanmaz çelik çubuk2 adet
Sert Ağaç Tahtası1 adet
Sert ağaç kavelalar1 adet
Düz Pul4 adet
Kopilya2 adetGerekli aletler:
Demir Testeresi
Eğeler (El Eğesi)
Kablosuz Matkap
Matkap Ucu Takımı11
11
The build in 3D
The build in 3D
FreeCAD model of this build, cut through the middle: the box, the spout running into the still disk, the turning disk with its rings between the still disk's, the hexagonal shaft with its two spirals of pins, and the geared stud, wheel and crank on the lid. The rotor was turned through 16 positions.
12
12
Churn
Churn
Turn the crank and pour heavy cream at about 15 °C, checked with the thermometer, into the hopper, about 15 litres in all, keeping the disk turning fast. Keep turning, timing it. When the butter comes the pins gather it in the middle: lift the lid, take out the shaft and the butter, drain the buttermilk, wash the butter in cold water until it runs clear, salt and weigh it.
Bu adım için malzemeler:
Yağlı krema15 l
İri Deniz Tuzu1 adet
Su1 adetGerekli aletler:
Takılı kalan problu termometre
Kronometre
Dijital Mutfak Terazisi
Büyük paslanmaz çelik karıştırma kâsesi13
13
Troubleshooting
Troubleshooting
Ring-disk churn troubleshooting.
Flow
Loading...
14
14
History and honest limits
History and honest limits
**Daniel C. Brown** of New York, US 26,880, 24 January 1860, "Churn". He claimed the disks F and G with the rings on their inner sides. His disks were wood or metal; ours are printed. His hopper is a jointed bucket; ours is a funnel on a tube. The patent gives no sizes; every size here is ours.
Malzemeler
14- 3 adetYer Tutucu
- 2 adetYer Tutucu
- 30 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 3 adetYer Tutucu
- 1 adetYer Tutucu
- 2 adetYer Tutucu
- 4 adetYer Tutucu
- 15 lYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
Gerekli Aletler
19- 1 vendor sell this, none ship to you yetYer Tutucu
- Yer Tutucu
- 1 vendor sell this, none ship to you yetYer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- 1 vendor sell this, none ship to you yetYer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
Tasarım dosyaları
5Bu planla yapılan
İlgili Blueprint'ler
Bu blueprint'ler bilgi paylaşır — teknikler, malzemeler veya ilkeler

Swinging-Wedge Churn: A Wedge Dasher Sweeps a Curved Bottom and Strikes the Sloping Ends Squarely
Buttercup tarafından
Ağaç işleri
4
0
0
0
0
0

Double Rotary Crag Churn: Two Shafts of Four-Edged Arms Turn Through Each Other in Twin Half-Cylinders
Buttercup tarafından
Ağaç işleri
13
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
TheChef tarafından
ZANAAT
63
0
0
0
0
0
CC0 Kamu Malı
Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.
Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

