İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Swinging-Wedge Churn: A Wedge Dasher Sweeps a Curved Bottom and Strikes the Sloping Ends Squarely
Buttercup

Oluşturan

Buttercup

11. Kasım 2026IE
4
0
0
0
0

Swinging-Wedge Churn: A Wedge Dasher Sweeps a Curved Bottom and Strikes the Sloping Ends Squarely

Josiah P. Fitch of New York received US 26,841, dated 17 January 1860, for a churn. A dasher shaped like a truncated wedge swings back and forth on a cross-head under the cover, sweeping the tub's curved bottom and meeting its sloping ends squarely, so the cream is squeezed against the ends and, unable to run back under the dasher, rises and falls over it. A curved guard on the staff closes the slot in the cover, and a hand rest adjusts to the churner's height. The patent gives no sizes; every size here is ours.
Orta
About 2 days

Talimatlar

1

Setting out the tub from the wedge

Jupyter defteri yükleniyor…
2

A dasher rocked about a level pivot, two months before

Bunting rocked his dasher from a crank. Fitch swings his by hand and shapes the tub round its path.
3

Read US 26,841

"The churn tub being partly filled with cream, the dasher is moved back and forth. This operation causes the cream to be compressed between the inclined portions of the ends of the tub and the taper sides of the dasher and also to be kept in circulation, for as it is impossible for it to run back under the bottom of the dasher, it necessarily rises and falls over the top of the same back into the center of the tub."
4

Tub A

Mark the pivot on two 20 mm hardwood sides and set out the inside outline from the notebook: the bottom an arc of 360 mm radius about the pivot, each end rising from it along a line 27.6 degrees from upright to a point 157 mm out and 149 mm below the pivot, then upright to 50 mm above the pivot. Cut the sides 20 mm outside that outline, rout a rebate along it, and bore each 17 mm at the pivot. Bend 1.5 mm stainless sheet, 260 mm wide, to the outline and screw it into the rebates with silicone sealant, the sides 260 mm apart inside. Fit four legs and a cover with a slot 36 mm wide, 150 mm long, across the middle.

Bu adım için malzemeler:

Sert Ağaç TahtasıSert Ağaç Tahtası3 adet
Paslanmaz çelik levhaPaslanmaz çelik levha1 adet
Silikon Dolgu MacunuSilikon Dolgu Macunu1 adet
Ahşap vidalarAhşap vidalar40 adet
Ahşap TutkalıAhşap Tutkalı1 adet

Gerekli aletler:

PusulaPusula
Dekupaj TestereDekupaj Testere
Freze motoruFreze motoru
Daire testere tezgâhıDaire testere tezgâhı
Sac makasıSac makası
Kablosuz MatkapKablosuz Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Çubuklu işkenceÇubuklu işkence
Şerit MetreŞerit Metre
5

Wedge B, cross-head D, guard F and hand rest E

Cut the wedge from hardwood 250 mm across: 110 mm wide at its top, 50 at its foot, 230 tall. Fix it on a 30 mm hardwood staff so its foot is 350 mm below the pivot. Make the cross-head a hardwood bar 40 x 30 mm across the tub, fixed on the staff, with a 16 mm stainless rod through it whose ends turn in the sides' holes. Above it bend a strip of stainless sheet 60 mm wide to a 45 mm radius round the pivot, reaching 80 degrees each way, and fix it to the staff as the guard F under the cover's slot. Make the hand rest a hardwood collar with a handle, held at any height on the staff by a set screw.

Bu adım için malzemeler:

Sert Ağaç TahtasıSert Ağaç Tahtası1 adet
Sert ağaç kavelalarSert ağaç kavelalar1 adet
Paslanmaz çelik çubukPaslanmaz çelik çubuk1 adet
Paslanmaz çelik levhaPaslanmaz çelik levha1 adet
Shaft CollarShaft Collar2 adet
Makine vidalarıMakine vidaları3 adet
Ahşap TutkalıAhşap Tutkalı1 adet

Gerekli aletler:

Daire testere tezgâhıDaire testere tezgâhı
Dekupaj TestereDekupaj Testere
Kablosuz MatkapKablosuz Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Demir TesteresiDemir Testeresi
Eğeler (El Eğesi)Eğeler (El Eğesi)
Sac makasıSac makası
Tornavida takımıTornavida takımı
Zımpara KağıdıZımpara Kağıdı
6

The build in 3D

FreeCAD model of this build, one side and the cover cut away: the tub with its curved bottom and sloping ends, the wedge on its staff and cross-head, the guard and the hand rest. The wedge was swung through its full travel; at each end it lies against the sloping end.
Tasarım DosyasıBLENDCC0 - Free
7

Churn

Pour heavy cream at about 15 °C into the tub, checked with the thermometer, about a third full (about 10 litres). Set the hand rest at a comfortable height and swing the staff steadily from end to end, timing it. When the butter comes, lift the cover and dasher out, take out the butter, drain the buttermilk, wash the butter in cold water until it runs clear, salt and weigh it.

Bu adım için malzemeler:

Yağlı kremaYağlı krema10 l
İri Deniz Tuzuİri Deniz Tuzu1 adet
SuSu1 adet

Gerekli aletler:

Takılı kalan problu termometreTakılı kalan problu termometre
KronometreKronometre
Dijital Mutfak TerazisiDijital Mutfak Terazisi
Büyük paslanmaz çelik karıştırma kâsesiBüyük paslanmaz çelik karıştırma kâsesi
8

Troubleshooting

Swinging-wedge churn troubleshooting.

Flow

Loading...
9

History and honest limits

**Josiah P. Fitch** of New York, US 26,841, 17 January 1860, "Churn". He claimed the curved guard F on the dasher staff with the dasher and tub, and the adjustable hand rest E with them. His dasher could be hollow, to hold hot water; ours is solid. The patent gives no sizes; every size here is ours, and setting the sloping ends along the wedge's faces at the end of its swing is our reading of "strikes ... squarely".

Malzemeler

12

Gerekli Aletler

17

Tasarım dosyaları

1

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...