SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Building a Methane Gas Leak Detector
Ed

Oluşturan

Ed

13. Temmuz 2026FI
41
0
0
0
0

Building a Methane Gas Leak Detector

Build a circuit that sniffs out methane — the main component of natural gas — and alarms when it rises. An MQ-4 sensor's reading climbs when combustible gas is present; the Arduino compares it to clean air and triggers a buzzer and red LED. A great combustible-gas sensing project — with two honest notes: methane is flammable, and this is a demonstration, NOT a certified gas-leak detector.

Orta
1-2 hours

Talimatlar

1

Wire the sensor, buzzer and LED

On the breadboard: MQ-4 VCC to Arduino 5V, GND to GND, and its analog output (AOUT) to A0. Active buzzer + to pin 8, - to GND. Red LED anode to pin 7 through a 330 Ω resistor, cathode to GND.

Bu adım için malzemeler:

Arduino Uno R3Arduino Uno R31 adet
Methane CNG Gas Sensor - MQ-4Methane CNG Gas Sensor - MQ-41 adet
Aktif buzzer modülüAktif buzzer modülü1 adet
5 mm LED5 mm LED1 adet
330 ohm direnç330 ohm direnç1 paket
Devre TahtasıDevre Tahtası1 adet
Jumper KablolarJumper Kablolar1 paket
2

Connect and open the IDE

Plug the Arduino into your computer with the USB cable, open the Arduino IDE, and select Arduino Uno and its serial port.

Gerekli aletler:

Arduino IDE Kurulu BilgisayarArduino IDE Kurulu Bilgisayar
USB-B kablosuUSB-B kablosu
3

Upload the detector sketch

Paste this sketch and upload. It warms the sensor, records a clean-air baseline, then sounds the buzzer and lights the LED whenever the reading rises above that baseline.

methane_detector.inoarduino
// Methane / natural-gas leak INDICATOR using an MQ-4 sensor.
// NOT a certified gas-leak detector - see the safety note. Methane is flammable.
// MQ-4 analog output on A0; buzzer on pin 8; red warning LED on pin 7.

const int MQ4_PIN = A0;
const int BUZZER_PIN = 8;
const int LED_PIN = 7;

int cleanAirValue = 0;          // baseline, measured at startup
const int ALARM_MARGIN = 150;   // how far above baseline triggers the alarm

void setup() {
  pinMode(BUZZER_PIN, OUTPUT);
  pinMode(LED_PIN, OUTPUT);
  Serial.begin(9600);

  Serial.println("Warming up the MQ-4 (2 min) in clean air...");
  delay(120000);
  cleanAirValue = analogRead(MQ4_PIN);
  Serial.print("Clean-air baseline: ");
  Serial.println(cleanAirValue);
}

void loop() {
  int reading = analogRead(MQ4_PIN);
  Serial.println(reading);

  if (reading > cleanAirValue + ALARM_MARGIN) {
    digitalWrite(LED_PIN, HIGH);      // combustible gas above baseline -> alarm
    digitalWrite(BUZZER_PIN, HIGH);
  } else {
    digitalWrite(LED_PIN, LOW);
    digitalWrite(BUZZER_PIN, LOW);
  }
  delay(500);
}
4

Warm up, baseline and test SAFELY

Power it in fresh air and let the 2-minute warm-up set the baseline (a new MQ-4 also needs a 24–48 h burn-in). Test with only a TINY controlled source in a well-ventilated room — a brief puff of gas from an UNLIT lighter held near the sensor. NEVER test with a real gas leak, a large amount of gas, or anywhere near a flame or spark. Adjust ALARM_MARGIN for sensitivity.

5

Safety limits

Methane is highly flammable and, in enough concentration, explosive. This circuit is a LEARNING project and at best a supplementary indicator — it is NOT a certified gas-leak detector: the hobby MQ-4 gives a relative reading, not calibrated ppm, drifts, and needs re-baselining. For real protection use a certified natural-gas detector, and if you ever smell gas, do not switch anything on or off — leave and call your gas utility.

Malzemeler

7

Gerekli Aletler

3
Tahmini toplam
Yapan kişinin satın aldıkları. Fiyatsız görünen malzemeleri nereden alıyorsanız oradan temin edersiniz.
$5.12

İlgili Blueprint'ler

Bu blueprint'ler bilgi paylaşır — teknikler, malzemeler veya ilkeler

Building a Carbon Monoxide Detector

Building a Carbon Monoxide Detector

Ed tarafındanFI

Dijital

85
0
0
0
0
0
Building an Air-Quality Monitor

Building an Air-Quality Monitor

Ed tarafındanFI

Dijital

38
0
0
0
0
0

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...