İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER

Ice-Chamber Air Churn: The Hollow Dasher Pumps the Same Air Round Through Ice and Cream
James H. Bump of Morris, New York, received US 21,871, dated 26 October 1858, for a churn with an ice chamber on its lid. A hollow dasher with a valve draws air from the ice chamber on every up stroke and forces it into the cream on every down stroke; the air pushed up out of the case returns through a tube into the ice chamber, so the same air goes round, cooled each time.
This rung builds it in a 20-litre bucket with printed parts and a lever.
Orta
About 5 hours, plus printing
Talimatlar
1
1
Air, depth and lever
Air, depth and lever
Jupyter defteri yükleniyor…
2
2
Air through a hollow dasher, before it
Air through a hollow dasher, before it
Marcell blew room air down a hollow dasher shaft. Bump draws it from an ice chamber and sends it round again.
3
3
Read US 21,871
Read US 21,871
"At every upward movement of the staff F, the air from the chamber C, rushes down within the staff F, into the chamber d ... and as the dasher descends the valve e, closes and the air within will be forced into the cream j, and at the same time the air in the case above the cream will be compressed by the rising of the cream j ... and said air will pass up the space f, into the chamber C".
4
4
Print the tube E
Print the tube E
Tube E, 40 mm across and 155 mm long, with its flange under lid B. PETG, 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
5
5
Print the clamp ring
Print the clamp ring
The ring that clamps tube E's flange, lid B and the chamber floor together. PETG, 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
6
6
Print the box a
Print the box a
Upper box a, 110 mm tall, with the staff's top guide. PETG, 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
7
7
Print the box a'
Print the box a'
Lower box a', with the four notches that do the work of Bump's grooves. PETG, 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
8
8
Print the dasher G
Print the dasher G
The bell dasher, 160 mm across, with chamber d open below. It needs a 160 mm bed; print it top down. PETG, 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
9
9
Print the flap e
Print the flap e
The valve flap with its two hinge knuckles. PETG, 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
10
10
Print the staff head
Print the staff head
The block that closes the staff's top and takes pin h. PETG, 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
11
11
Lid, tube and ice chamber
Lid, tube and ice chamber
Use a food-grade 20-litre bucket and its lid (lid B), and a round food container 200 mm across and 130 mm deep as chamber C, its own lid as lid D. Cut a 40 mm hole in the middle of lid B and of the container's floor. Push tube E up from under lid B, set the container on the lid and the clamp ring over the tube, and fix them with four M4 screws and lock nuts. Cut a 30 mm hole in the middle of lid D.
Bu adım için malzemeler:
PETG filament1 adet
20 Litrelik Kova1 adet
Gıda sınıfı saklama kabı1 adet
Makine vidaları4 adet
Naylon Fiberli Emniyet Somunu4 adetGerekli aletler:
FDM 3B yazıcı
Panç testere seti
Kablosuz Matkap
Matkap Ucu Takımı
Tornavida takımı
Kurbağacık anahtar12
12
Boxes and hollow staff
Boxes and hollow staff
Bolt box a on top of lid D and box a' under it through their flanges, three M4 screws, the notches of a' against the lid. Cut the stainless tube (16 mm, 1 mm wall) to 549 mm. Drill two 5 mm holes c straight through it, crossed, 389 mm from its foot, and a 4.4 mm hole across it 6 mm and 534 mm from its foot for the cross screws.
Bu adım için malzemeler:
Makine vidaları3 adet
Naylon Fiberli Emniyet Somunu3 adet
Paslanmaz çelik boru1 adetGerekli aletler:
Boru kesici
Kablosuz Matkap
Matkap Ucu Takımı
Eğeler (El Eğesi)
Tornavida takımı13
13
Dasher and valve
Dasher and valve
Hang the flap e on the lug in the dasher's chamber with an M3 screw and lock nut so it covers the air hole from below and swings down freely. Push the staff's foot 12 mm into the dasher's top and fix it with an M4 screw across.
Bu adım için malzemeler:
Makine vidaları2 adet
Naylon Fiberli Emniyet Somunu2 adetGerekli aletler:
Tornavida takımı
Kurbağacık anahtar14
14
Upright and lever
Upright and lever
Cut a hardwood foot 90 x 34 x 30 mm and bolt it to lid B 120 mm from the middle, with two M6 bolts through a hardwood backing strip under the lid. Screw a hardwood upright 30 x 45 mm, 337 mm tall, on it. Cut two lever strips 30 x 12 mm, 480 mm long; drill each 20 mm from one end for pin g and cut a 6.5 mm slot from 110 to 135 mm past it for pin h. Lower the staff through tube E and the boxes, push on the staff head with an M4 screw across, and bolt the strips either side of the upright (pin g) and of the head (pin h) with M6 bolts, washers and lock nuts.
Bu adım için malzemeler:
Sert Ağaç Tahtası1 adet
Altıköşe cıvata takımı4 adet
Düz Pul8 adet
Naylon Fiberli Emniyet Somunu5 adet
#8 x 1" ahşap vidası4 adet
Makine vidaları1 adetGerekli aletler:
El Testeresi
Kablosuz Matkap
Matkap Ucu Takımı
Eğeler (El Eğesi)
Zımpara Kağıdı
Kurbağacık anahtar
Şerit Metre15
15
The build in 3D
The build in 3D
FreeCAD model of this build at mid stroke, the near quarter of the bucket, chamber and boxes cut away: lid B with tube E, chamber C and lid D, boxes a and a', the hollow staff with its holes c, the bell dasher with flap e, the upright and the forked lever.
16
16
Churn
Churn
Pour 8 litres of heavy cream at about 15 °C into the bucket, checked with the thermometer. Fit lid B with the dasher in place, fill chamber C with crushed ice round tube E and close lid D. Work the lever up and down steadily, the full 100 mm stroke, and time it. When the butter comes, lift the lid out, pour off the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.
Bu adım için malzemeler:
Yağlı krema8 l
Kırılmış buz2 kg
İri Deniz Tuzu1 adet
Su1 adetGerekli aletler:
Takılı kalan problu termometre
Kronometre
Dijital Mutfak Terazisi
Büyük paslanmaz çelik karıştırma kâsesi17
17
Troubleshooting
Troubleshooting
Ice-chamber churn troubleshooting.
Flow
Loading...
18
18
History and honest limits
History and honest limits
**James H. Bump** of Morris, Otsego County, New York, US 21,871, 26 October 1858, "Churn". He held that the cream, "by the absorption of oxygen is fully acetified" and kept cool by the iced air, gives butter "of a superior quality". He disclaimed a hollow dasher rod for air and forcing air into cream as done before, and claimed only the chamber C through which the air is made to circulate. He gave no sizes and named only "metal boxes": every size, material and the 8 litres at 15 °C are ours. Our notches in box a' stand in for his grooves cut in lid D.
Malzemeler
14- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 10 adetYer Tutucu
- Yer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 4 adetYer Tutucu
- 8 adetYer Tutucu
- 4 adetYer Tutucu
- 8 lYer Tutucu
- 2 kgYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
Gerekli Aletler
15- Yer Tutucu
- Yer Tutucu
- 1 vendor sell this, none ship to you yetYer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- 1 vendor sell this, none ship to you yetYer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
Tasarım dosyaları
8Bu planla yapılan
İlgili Blueprint'ler
Bu blueprint'ler bilgi paylaşır — teknikler, malzemeler veya ilkeler

Fan-Blown Jet Dasher Churn: A Fan on the Crank Shaft Blows Air Out Through the Dasher Below the Cream
Buttercup tarafından
YİYECEK & İÇECEK
43
0
0
0
0
0

Double-Dasher Lever Churn: Swing One Lever, One Dasher Rises as the Other Falls
Woody tarafından
Ağaç işleri
41
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
TheChef tarafından
ZANAAT
63
0
0
0
0
0
CC0 Kamu Malı
Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.
Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

