İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Button-Set Hinged-Slat Dasher Churn: Slats Deflect the Cream, a Button on the Rod Holds Them Open or Lets Them Shut
Buttercup

Oluşturan

Buttercup

11. Kasım 2026IE
9
0
0
0
0

Button-Set Hinged-Slat Dasher Churn: Slats Deflect the Cream, a Button on the Rod Holds Them Open or Lets Them Shut

S. N. Campbell of Elgin, Illinois, received US 25,804, dated 18 October 1859, for a churn. A lever pivoted on a post works a dasher that fits the box closely. Its hinged slats hang open as deflectors: drawn up, the dasher throws the cream down and to the sides; pushed down, it forces the cream up towards a cross piece in the middle. A button with two inclined surfaces on the rod's foot holds the slats open, or, turned half round, lets them shut on the down stroke, to suit the cream. The patent gives no sizes and does not say where the slats are hinged or how the button bears on them: those and every size here are ours.
Orta
About 2 days, plus printing

Talimatlar

1

The button: holding the slats open, or letting them shut

Jupyter defteri yükleniyor…
2

An up-and-down dasher fitting a box closely, three weeks before

Austin's middle dasher is a plain plate. Campbell's has hinged slats that deflect the cream, held open or let shut by a button on the rod.
3

Read US 25,804

"This dasher is constructed with movable slats H, H, which, when open, rest upon stop pins a, and serve the office of deflectors, and as the dasher is drawn up the cream is thrown below the slats and to the sides of the churn and as the dasher is pressed down the cream will be forced up and toward the center of the churn, and against a cross piece J, secured to the center of the dasher."
4

Print the button K

A disc 72 mm across and 6 mm thick with two inclined surfaces 60 mm long, one each side, both rising 7.5 mm towards the same end. PETG, 0.2 mm layers, 100 % infill.
Tasarım DosyasıSTLCC0 - Free
5

Box A, stand B, post D, lid E and lever C

From 20 mm hardwood make a box 400 x 300 mm and 380 mm deep inside, on four legs 50 mm square and 300 mm long. Screw a post 50 x 40 mm, 860 mm long, up the middle of the back. Cut a lid with a 32 mm hole in its middle. Bolt a lever 30 x 30 mm, 640 mm long, to the post's top so it reaches over the lid's middle to the front. Fill the box with water overnight so it swells tight, then empty it.

Bu adım için malzemeler:

Sert Ağaç TahtasıSert Ağaç Tahtası3 adet
Yumuşak ağaç 70x70 mmYumuşak ağaç 70x70 mm1 adet
Ahşap TutkalıAhşap Tutkalı1 adet
Ahşap vidalarAhşap vidalar30 adet
Altıköşe cıvata takımıAltıköşe cıvata takımı2 adet
Naylon Fiberli Emniyet SomunuNaylon Fiberli Emniyet Somunu2 adet
Düz PulDüz Pul4 adet

Gerekli aletler:

Daire testere tezgâhıDaire testere tezgâhı
El TesteresiEl Testeresi
Kablosuz MatkapKablosuz Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Yassı matkap ucu takımıYassı matkap ucu takımı
Çubuklu işkenceÇubuklu işkence
Marangoz gönyesiMarangoz gönyesi
Şerit MetreŞerit Metre
SuSu
Kurbağacık anahtarKurbağacık anahtar
6

Dasher G and its slats

Make two end bars 296 x 40 x 20 mm and join them with the cross piece J, 396 x 40 x 30 mm, bored 31 mm in its middle. Cut two inner slats H 380 x 63 x 12 mm, each with a tab 20 x 9 mm on its inner edge 10 to 30 mm from the middle, and two outer slats H' 380 x 52 x 12 mm. Bore each along its length for a 6 mm stainless hinge pin, H 3 mm in from its inner edge and H' 4 mm in, and hang them between the end bars on pins 392 mm long, H 32 mm and H' 98 mm each side of the middle. Fix 6 mm stop pins, 20 mm long, into the end bars under the slats: 80 mm out and 27 mm below the hinges for H, 130 mm out and 21.5 mm below for H'. Glue posts 20 x 10 x 19 mm on the slats, 120 mm each side of the middle, 40 mm out from each hinge, and join each pair with a piece L 76 x 20 x 6 mm on pins.

Bu adım için malzemeler:

Sert Ağaç TahtasıSert Ağaç Tahtası2 adet
Paslanmaz çelik çubukPaslanmaz çelik çubuk2 adet
Ahşap TutkalıAhşap Tutkalı1 adet
KopilyaKopilya12 adet
Düz PulDüz Pul12 adet

Gerekli aletler:

Daire testere tezgâhıDaire testere tezgâhı
Kablosuz MatkapKablosuz Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Demir TesteresiDemir Testeresi
Eğeler (El Eğesi)Eğeler (El Eğesi)
Zımpara KağıdıZımpara Kağıdı
Şerit MetreŞerit Metre
Çubuklu işkenceÇubuklu işkence
7

Rod F and button K

Turn a hardwood rod F 30 mm across and 440 mm long, with a cross handle at its top to turn it. Pass it down through J and glue the button on its foot, below J, so that in one position its inclined surfaces lie under the slats' tabs and hold the slats open on their pins. Join its top to the lever with a pin in a slot. Set the dasher in the box and the lid on.

Bu adım için malzemeler:

Sert ağaç kavelalarSert ağaç kavelalar1 adet
Ahşap TutkalıAhşap Tutkalı1 adet
Paslanmaz çelik çubukPaslanmaz çelik çubuk1 adet
KopilyaKopilya2 adet
PETG filamentPETG filament1 adet

Gerekli aletler:

FDM 3B yazıcıFDM 3B yazıcı
Kablosuz MatkapKablosuz Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Demir TesteresiDemir Testeresi
8

The build in 3D

FreeCAD model of this build, one side and one end left off: the box on its stand, the post and lever, the rod, and the dasher with the cross piece J, the hinged slats H and H' on their stop pins, the pieces L and the button K under the tabs. Checked at three heights, with the slats held open and with them shut.
Tasarım DosyasıBLENDCC0 - Free
9

Churn

Pour about 20 litres of heavy cream at about 15 °C into the box, checked with the thermometer, and put the lid on. Work the lever up and down, timing it. For thin cream keep the button holding the slats open; if the cream thickens, turn the rod half round so the slats shut on each down stroke. When the butter comes, lift the dasher out, drain the buttermilk, wash the butter in cold water until it runs clear, salt and weigh it.

Bu adım için malzemeler:

Yağlı kremaYağlı krema20 l
İri Deniz Tuzuİri Deniz Tuzu1 adet
SuSu1 adet

Gerekli aletler:

Takılı kalan problu termometreTakılı kalan problu termometre
KronometreKronometre
Dijital Mutfak TerazisiDijital Mutfak Terazisi
Büyük paslanmaz çelik karıştırma kâsesiBüyük paslanmaz çelik karıştırma kâsesi
10

Troubleshooting

Hinged-slat dasher troubleshooting.

Flow

Loading...
11

History and honest limits

**S. N. Campbell** of Elgin, Kane County, Illinois, US 25,804, 18 October 1859, "Churn". He claimed "the arrangement and combination of the button K, dasher rod F, movable slats H, H', pieces L, and bar J". The patent gives no sizes and does not say where the slats are hinged, how the button's surfaces bear on them, or how the pieces L join H' to H: the hinge lines, the tabs, the button's surfaces, the links and every size here are our reading.

Malzemeler

14

Gerekli Aletler

18

Tasarım dosyaları

2
  • campbell-button-set-hinged-slat-dasher-churn-button-k.stlSTLCC0
  • campbell-button-set-hinged-slat-dasher-churn.blendBLENDCC0

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...