SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Closed-Globe Egg Beater: Concentric Rings in a Shut Sphere
Beaten in an open bowl, egg spatters and the air is not forced into it.
James M. Jay of Canton, Ohio, received US 27,054, dated 7 February 1860, for an egg beater whose case is a hollow globe of two halves hinged and caught together; a horizontal shaft through it carries concentric rings, the outer one close to the inside so it sweeps the bottom, turned by a wheel and gear on a stand. "The air which occupies the upper part ... is so closely confined that it can not escape during the operation of beating the eggs, consequently it is carried down and mixed thoroughly with the eggs."
This rung works out the air-to-egg ratio, then prints the ring dasher and gears, closes it in two bowls, and times a beating.
Orta
About 5 hours, plus printing
Talimatlar
1
1
Air shut in with the eggs
Air shut in with the eggs
Jupyter defteri yükleniyor…
2
2
A dasher in a closed box before it
A dasher in a closed box before it
The embedded blueprint spins a dasher in a square box. Jay shuts the eggs in a globe so the air is driven into them.
3
3
Read US 27,054
Read US 27,054
"In my egg beater the air which occupies the upper part of the hollow bottom B, together with that which fills the cover or cap C, is so closely confined that it can not escape during the operation of beating the eggs, consequently it is carried down and mixed thoroughly with the eggs by the rings or dashes H', while the eggs are carried up and through the air in the cap or case C, so that a perfect mixture of the air and eggs is effected."
4
4
Print the rings and gears
Print the rings and gears
Print the concentric-ring dasher (/uploads/blueprints/closed-globe-egg-beater-rings.stl), the 36-tooth wheel (/uploads/blueprints/closed-globe-egg-beater-wheel-36.stl) and the 12-tooth gear (/uploads/blueprints/closed-globe-egg-beater-gear-12.stl). Print in PETG at 0.2 mm layers, 30 % infill, 4 walls.
Bu adım için malzemeler:
PETG filament1 adetGerekli aletler:
FDM 3B yazıcı5
5
Make the globe
Make the globe
Take two matching bowls 120 mm across from the set. Drill both rims at opposite points for the shaft, 5.5 mm, so the shaft lies on the joint.
Bu adım için malzemeler:
Karıştırma kâsesi seti1 adetGerekli aletler:
Kablosuz Matkap
Matkap Ucu Takımı
Dijital Kumpas 6 İnç6
6
Shaft, rings and stand
Shaft, rings and stand
Pass a 5 mm rod through one bowl's holes and the dasher's hub, and epoxy the hub at the centre. Epoxy the 12-tooth gear on the rod outside. Mount the 36-tooth wheel with a crank on an M5 screw on a hardwood upright so it meshes, and stand the lower bowl in a plywood ring.
Bu adım için malzemeler:
Yumuşak Çelik Çubuk1 adet
İki bileşenli epoksi1 adet
Sert Ahşap Blok1 adet
Kontrplak levha1 adet
Makine vidaları1 adet
Düz Pul1 adet
Altıgen Somun1 adet
#8 x 1" ahşap vidası1 adetGerekli aletler:
Demir Testeresi
Kıl TestereKablosuz MatkapMatkap Ucu Takımı
Kurbağacık anahtar
Tornavida takımı7
7
The patent drawing
The patent drawing
US 27,054 drawing sheet, public domain (expired patent).
8
8
Closed against open
Closed against open
Beat two egg whites with the top bowl clamped on and time them to stiff peaks; then again with the top off. Compare the times and the volume of foam.
Bu adım için malzemeler:
Yumurta4 adetGerekli aletler:
Kronometre
Dijital Mutfak Terazisi9
9
A globe that leaks, rings that scrape
A globe that leaks, rings that scrape
Closed-globe egg beater troubleshooting.
Flow
Loading...
10
10
History and honest limits
History and honest limits
**James M. Jay** of Canton, Ohio, assignor to himself and John Danner, received US 27,054, dated 7 February 1860. The halves are turned to break joints and fit tight; a hook on the cover hangs on a pivot between lugs, and a swinging catch holds the cover down; the shaft's bearings are in the lower half's edge, the cover cut to fit over them. He wrote that it does not matter whether one or more eggs are beaten.
**Honest limits.** FDM prints hold food in their layer lines, so wash well and replace when worn. Two bought bowls stand in for his turned halves, without a hinge. Your times are the result.
Malzemeler
11- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 4 adetYer Tutucu
Gerekli Aletler
10- Yer Tutucu
- 1 vendor sell this, none ship to you yetYer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
İlgili Blueprint'ler
Bu blueprint'ler bilgi paylaşır — teknikler, malzemeler veya ilkeler
Counter-Rotating Egg Beater: One Wheel, Two Beaters Turning Opposite Ways
Martin tarafından
YİYECEK & İÇECEK
17
0
0
0
0
0
Stepped Spiral Egg Beater: A Stepped Dasher Spun in a Square Box
Martin tarafından
YİYECEK & İÇECEK
8
0
0
0
0
0
Gear Trains: Idlers, Compounding and Hitting a Given Ratio
Martin tarafından
Mekanik
26
0
0
0
0
0
CC0 Kamu Malı
Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.
Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.