İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Propeller-Dasher Churn: A Paddle Carved From One Block Like a Ship's Screw, With Fold-Out Breakers
Woody

Oluşturan

Woody

9. Kasım 2026NO
9
0
0
0
0

Propeller-Dasher Churn: A Paddle Carved From One Block Like a Ship's Screw, With Fold-Out Breakers

Jacob Closs of Decatur, Indiana, received US 24,197, dated 31 May 1859, for a tub churn whose dasher works like a propeller screw. It is carved from one block of wood 4 to 6 in. square, bored for an upright shaft and cut into two twisted paddles. A crank turns a large wheel that drives a small cog wheel on the shaft. Two breakers along the side stand out while churning and are laid back against the side, by wires through the lid, while gathering the butter. This rung carves the dasher from hardwood and fits it in a 20-litre bucket.
İleri
About 1 day, plus printing

Talimatlar

1

Patent sizes and ours

Jupyter defteri yükleniyor…
2

Beaters set like a screw, before it

The Robies set beaters spirally along a level shaft. Closs carves a true screw from one block on an upright shaft.
3

Read US 24,197

"These dashes or paddles are made of a single piece of wood of from 4 to 6 inches square, with length less than diameter of the churn. A hole is bored through the center ... Then saw in on either side of the shaft on the corners above and below and block out leaving sufficient bulk of timber to permit the paddles to be shaped".
4

Print the wheel B

The 168 mm wheel with 48 teeth on its face. Print it flat, teeth up. PETG, 0.2 mm layers, 40 % infill, 4 walls; wash before first use.
Tasarım DosyasıSTLCC0 - Free
5

Print the cog wheel

The 16-tooth cog wheel for the shaft's top. PETG, 0.2 mm layers, 40 % infill, 4 walls; wash before first use.
Tasarım DosyasıSTLCC0 - Free
6

Print the socket

The foot bearing for the shaft. PETG, 0.2 mm layers, 40 % infill, 4 walls; wash before first use.
Tasarım DosyasıSTLCC0 - Free
7

Carve the dasher

Glue up a hardwood block 125 x 125 mm and 190 mm long and bore a 30.5 mm hole through its middle, across its length at the centre. Mark the hub, 60 mm across, round the hole. Following Closs, saw in on either side of the hub at the corners above and below, and chisel the waste away so two paddles are left, each twisted like a screw: about 70 degrees from level next to the hub and 38 degrees at the tip, the two turned the same way. Round the paddles to 190 mm across overall, leave them about 14 mm thick, and sand smooth.

Bu adım için malzemeler:

Sert Ağaç TahtasıSert Ağaç Tahtası1 adet
Ahşap TutkalıAhşap Tutkalı1 adet

Gerekli aletler:

İşkencelerİşkenceler
El TesteresiEl Testeresi
Yassı matkap ucu takımıYassı matkap ucu takımı
Kablosuz MatkapKablosuz Matkap
Marangoz keskileriMarangoz keskileri
İletkiİletki
Eğeler (El Eğesi)Eğeler (El Eğesi)
Zımpara KağıdıZımpara Kağıdı
8

Tub, lid and breakers

Use a food-grade 20-litre bucket. Cut a 12 mm plywood lid 310 mm across in two halves, with a 32 mm hole at the middle and a 5 mm hole 118 mm out on each side for the wires. Screw the socket to the middle of the bucket's floor. Cut two breakers F from 12 mm plywood, 335 mm tall, 34 mm wide at the foot and 43 at the top, and hinge each by its outer edge to the bucket's wall on opposite sides, 25 mm above the floor. Bend a 3 mm stainless wire to each breaker's top inner corner, up through the lid, with a hook G on top: pull it to stand the breaker out, push it to lay it back.

Bu adım için malzemeler:

20 Litrelik Kova20 Litrelik Kova1 adet
Kontrplak levhaKontrplak levha1 adet
PETG filamentPETG filament1 adet
Makine vidalarıMakine vidaları5 adet
Naylon Fiberli Emniyet SomunuNaylon Fiberli Emniyet Somunu5 adet
Kapı menteşesiKapı menteşesi4 adet
Paslanmaz çelik çubukPaslanmaz çelik çubuk1 adet

Gerekli aletler:

FDM 3B yazıcıFDM 3B yazıcı
Dekupaj TestereDekupaj Testere
Kablosuz MatkapKablosuz Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Tezgah MengenesiTezgah Mengenesi
Demir TesteresiDemir Testeresi
Tornavida takımıTornavida takımı
Şerit MetreŞerit Metre
9

Shaft, wheels and crank

Cut a 30 mm hardwood dowel 474 mm long as shaft A. Push it through the dasher until the dasher's foot is 30 mm above the floor and pin it with a screw across. Stand the shaft in its socket, put the lid halves on and fix the cog wheel on the shaft's top with an M4 screw across. Screw a hardwood upright 44 x 30 mm, 188 mm tall, to one lid half, bored 12.5 mm at 158 mm up; run a 12 mm stainless rod through it and wheel B so B meshes with the cog wheel, and fix a hardwood crank C with a dowel handle on the rod's far end.

Bu adım için malzemeler:

Sert ağaç kavelalarSert ağaç kavelalar1 adet
Ahşap vidalarAhşap vidalar6 adet
Makine vidalarıMakine vidaları2 adet
Naylon Fiberli Emniyet SomunuNaylon Fiberli Emniyet Somunu2 adet
Sert Ağaç TahtasıSert Ağaç Tahtası1 adet
Paslanmaz çelik çubukPaslanmaz çelik çubuk1 adet
Ahşap TutkalıAhşap Tutkalı1 adet

Gerekli aletler:

El TesteresiEl Testeresi
Kablosuz MatkapKablosuz Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Demir TesteresiDemir Testeresi
Tornavida takımıTornavida takımı
10

The build in 3D

FreeCAD model of this build, a quarter of the bucket and lid cut away: the carved two-paddle dasher on the shaft in its socket, the two breakers standing out on their wires, the lid halves, the upright with wheel B, the cog wheel and the crank.
Tasarım DosyasıBLENDCC0 - Free
11

Churn

Pull the wires to stand the breakers out. Pour in about 10 litres of heavy cream at about 15 °C, checked with the thermometer, and put the lid on. Turn the crank steadily and time it. When the butter comes, push the wires down to lay the breakers back and turn slowly to gather the butter. Then lift the lid and shaft out, pour off the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.

Bu adım için malzemeler:

Yağlı kremaYağlı krema10 l
İri Deniz Tuzuİri Deniz Tuzu1 adet
SuSu1 adet

Gerekli aletler:

Takılı kalan problu termometreTakılı kalan problu termometre
KronometreKronometre
Dijital Mutfak TerazisiDijital Mutfak Terazisi
Büyük paslanmaz çelik karıştırma kâsesiBüyük paslanmaz çelik karıştırma kâsesi
12

Troubleshooting

Propeller churn troubleshooting.

Flow

Loading...
13

History and honest limits

**Jacob Closs** of Decatur, Adams County, Indiana, US 24,197, 31 May 1859, "Churn". He claimed the screw dashers with the breakers. His tub was about 12 in. across and 18 in. high and wider at the bottom; our bucket is about as wide but shallower and wider at the top. His block was 4 to 6 in. square; ours is 125 mm. The paddles' twist, the gearing and the other sizes are ours.

Malzemeler

14

Gerekli Aletler

19

Tasarım dosyaları

4

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...