İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Spiral-Beater Box Churn: Diamond-Holed and Hollow-Ended Beaters Drive the Cream End to End
Buttercup

Oluşturan

Buttercup

9. Kasım 2026IE
9
0
0
0
0

Spiral-Beater Box Churn: Diamond-Holed and Hollow-Ended Beaters Drive the Cream End to End

Harry and Royal V. Robie of Eaton, New York, received US 22,090, dated 16 November 1858, for a box churn with beaters set spirally on a level crank shaft. Every other beater has a diamond hole; the rest have a hollow (concave) end. All are narrow where they join the shaft, so the cream passes between them, and they drive it from one end of the box to the other. A chamber under the box, with a hinged door, holds something cold or warm to bring the cream to temperature. This rung builds it with a food-grade container in a pine body and printed beaters.
Orta
About 6 hours, plus printing

Talimatlar

1

Beaters, spacing and fill

Jupyter defteri yükleniyor…
2

Pierced dashers, before it

Farrington broke the cream on the holes of swinging dashers. The Robies pierce every other beater on a turning shaft.
3

Read US 22,090

"... the base of said beaters being made small and narrow where they enter the shaft in order to form an opening for the passage of the cream, between each of the beaters, while the holes in each alternate beater form another passage".
4

Print the beater B

Beater B, with the diamond hole. Print four. PETG, 0.2 mm layers, 30 % infill, 4 walls, with supports under the turned blade; wash before first use.
Tasarım DosyasıSTLCC0 - Free
5

Print the beater C

Beater C, with the hollow end. Print three. PETG, 0.2 mm layers, 30 % infill, 4 walls, with supports under the turned blade; wash before first use.
Tasarım DosyasıSTLCC0 - Free
6

Print the crank

The crank arm. PETG, 0.2 mm layers, 30 % infill, 4 walls, with supports under the turned blade; wash before first use.
Tasarım DosyasıSTLCC0 - Free
7

Print the collar

The collar that holds the shaft's far end. PETG, 0.2 mm layers, 30 % infill, 4 walls, with supports under the turned blade; wash before first use.
Tasarım DosyasıSTLCC0 - Free
8

Body and chamber

Use a food-grade container 400 x 280 mm inside and 250 mm deep, with a rim. From 18 mm pine cut two ends 362 x 750 mm with a 120 mm arch at the foot, two sides 444 x 630 mm, two rails 444 x 40 mm and a shelf 444 x 326 mm. Screw the sides between the ends, the rails inside the sides 3 mm below the top, and the shelf 200 mm up. Cut a 360 x 272 mm opening in the front side above the shelf and hang a 356 x 268 mm pine door in it on two butt hinges along its bottom edge.

Bu adım için malzemeler:

Çam tahtaÇam tahta3 adet
Ahşap TutkalıAhşap Tutkalı1 adet
Ahşap vidalarAhşap vidalar40 adet
Kapı menteşesiKapı menteşesi2 adet
#8 x 1" ahşap vidası#8 x 1" ahşap vidası8 adet

Gerekli aletler:

El TesteresiEl Testeresi
Dekupaj TestereDekupaj Testere
Kablosuz MatkapKablosuz Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
İşkencelerİşkenceler
Zımpara KağıdıZımpara Kağıdı
Tornavida takımıTornavida takımı
Şerit MetreŞerit Metre
9

Shaft A and beaters

Hang the container by its rim on the rails. Drill a 17 mm hole through both pine ends and both container ends, 150 mm above the container's inside floor. Cut the stainless tube (16 mm) to 574 mm and push it through. Slide on the seven beaters, B, C, B, C, B, C, B, 50 mm apart from the middle out, each a quarter turn round from the last, all blades turned the same way, and fix each with an M4 screw across hub and shaft. Fit the collar on the far end and the crank on the near end with M4 screws, and glue a 12 mm dowel 114 mm long into the crank as the handle.

Bu adım için malzemeler:

Gıda sınıfı saklama kabıGıda sınıfı saklama kabı1 adet
PETG filamentPETG filament1 adet
Paslanmaz çelik boruPaslanmaz çelik boru1 adet
Makine vidalarıMakine vidaları9 adet
Naylon Fiberli Emniyet SomunuNaylon Fiberli Emniyet Somunu9 adet
Sert ağaç kavelalarSert ağaç kavelalar1 adet
Ahşap TutkalıAhşap Tutkalı1 adet

Gerekli aletler:

FDM 3B yazıcıFDM 3B yazıcı
Kablosuz MatkapKablosuz Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Boru kesiciBoru kesici
Eğeler (El Eğesi)Eğeler (El Eğesi)
Tornavida takımıTornavida takımı
Kurbağacık anahtarKurbağacık anahtar
10

The build in 3D

FreeCAD model of this build: the pine body with its arched ends, the chamber door, the container on its rails, the shaft with seven spiral beaters, the collar and the crank.
Tasarım DosyasıBLENDCC0 - Free
11

Churn

Bring the cream to about 15 °C: in warm weather set a tray of ice in the chamber under the box, in cold weather a tray of warm water, and shut the door. Pour in about 12 litres of heavy cream, keeping it 20 mm below the shaft, and check it with the thermometer. Turn the crank steadily and time it. When the butter comes, lift the container out, pour off the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.

Bu adım için malzemeler:

Yağlı kremaYağlı krema12 l
Kırılmış buzKırılmış buz2 kg
İri Deniz Tuzuİri Deniz Tuzu1 adet
SuSu1 adet

Gerekli aletler:

Takılı kalan problu termometreTakılı kalan problu termometre
KronometreKronometre
Dijital Mutfak TerazisiDijital Mutfak Terazisi
Büyük paslanmaz çelik karıştırma kâsesiBüyük paslanmaz çelik karıştırma kâsesi
12

Troubleshooting

Spiral-beater churn troubleshooting.

Flow

Loading...
13

History and honest limits

**Harry Robie** and **Royal V. Robie** of Eaton, Madison County, New York, US 22,090, 16 November 1858, "Churn". They knew beaters set spirally round a level shaft were old, and claimed only the diamond-holed beater B with the hollow-ended beater C and the passage under their narrow bases. They gave no sizes or materials and no number of beaters: ours are seven at 50 mm and a quarter turn apart, blades turned 30 degrees. Their box (Fig. 1) has a rounded floor; our container is flat.

Malzemeler

15

Gerekli Aletler

16

Tasarım dosyaları

5

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...