İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Christmas Tree Stand: Three Legs Tied by Wire Links to a Nail in the Butt (Cook, 1902)
Woody

Oluşturan

Woody

13. Kasım 2026NO
9
0
0
0
0

Christmas Tree Stand: Three Legs Tied by Wire Links to a Nail in the Butt (Cook, 1902)

William Cook of New York received US 710,762, dated 7 October 1902, for a Christmas tree stand of three leaning legs and three wire links. The links meet under the tree on a nail driven up into the butt, and their other ends are fixed part way up the legs. The tops of the legs are screwed to the trunk. The tree's weight pushes the feet out, the links pull back, and the tops of the legs squeeze the trunk. We make it from pine and steel wire. All sizes are ours.
Başlangıç
About 3 hours

Talimatlar

1

Where the links go

Jupyter defteri yükleniyor…
2

Read US 710,762

"The tendency of legs A to spread by weight of tree causes an outward tension at wire nail F through the several links C and inward pressure on stem of tree by upper part of legs A. Thus the tree is held very secure and perfectly upright by two opposite forces acting a short space apart and derived from weight of tree."
3

Cut the legs

Saw three legs 700 mm long from 70 x 22 mm pine (ours). Set a bevel gauge to 30 degrees and cut both ends of each leg at that angle, parallel to each other, so the foot sits flat on the floor and the top lies along the trunk, as in his Fig. 2. Sand off the splinters.

Bu adım için malzemeler:

Çam tahtaÇam tahta1 adet

Gerekli aletler:

El TesteresiEl Testeresi
Ayarlı gönyeAyarlı gönye
Şerit MetreŞerit Metre
Kurşun kalemKurşun kalem
Zımpara KağıdıZımpara Kağıdı
4

Bend the links

Cut three pieces of 2.5 mm steel wire, each the link length from the notebook plus about 60 mm for the eyes. Bend a round eye at each end with round-nose pliers, as his Fig. 3, so the eyes' centres are the link length apart. Make all three the same.

Bu adım için malzemeler:

Çelik telÇelik tel3 adet

Gerekli aletler:

Yan keskiYan keski
Yuvarlak uçlu penseYuvarlak uçlu pense
Şerit MetreŞerit Metre
5

Staple the links to the legs

Mark each leg where the notebook says, on its inner face. Bend three U staples from the same wire (ours). Lay a link's outer eye on the mark and drive a staple over it into the leg, his staple H, leaving the eye free to turn.

Bu adım için malzemeler:

Çelik telÇelik tel1 adet

Gerekli aletler:

Yan keskiYan keski
Yuvarlak uçlu penseYuvarlak uçlu pense
Marangoz çekiciMarangoz çekici
6

Drill the tops of the legs

Drill a hole through the top of each leg, about 40 mm from its end, just big enough for the screw eye's shank to pass.

Gerekli aletler:

El matkabıEl matkabı
7

Nail the links to the butt

Saw the butt of the tree off square. Lay the tree on its side. Thread a long wire nail through the three free eyes of the links, his nail F, and drive it up into the middle of the bottom end of the tree.

Bu adım için malzemeler:

ÇivilerÇiviler1 adet

Gerekli aletler:

El TesteresiEl Testeresi
Marangoz çekiciMarangoz çekici
8

Fix the tops of the legs

Bring the top of each leg in against the trunk. Make a start hole in the trunk with an awl through the leg's hole, and turn a screw eye through the leg into the trunk until the leg is held tight, his screw-eye D. Do all three, then stand the tree up.

Bu adım için malzemeler:

Halkalı vidaHalkalı vida3 adet

Gerekli aletler:

BizBiz
9

Check it stands upright

All three feet should touch the floor and the links should be straight and tight. Look at the tree from two sides. To take it down, turn out the screw eyes and pull the nail; the links fold about the nail for storing.
10

Troubleshooting

Christmas tree stand troubleshooting.

Flow

Loading...
11

History and honest limits

**William Cook** of New York, US 710,762, dated 7 October 1902, filed 29 July 1901. He claimed "a Christmas-tree stand composed of legs, and links, one end of each link being connected with one leg at a point intermediate between the ends of the leg, and the opposite ends of the links being connected with each other to form a seat". He says the stand is "more economical of construction and more easily applied" and that "size of tree offers no obstacle". He names no materials and gives no sizes: the pine, the wire, the 700 mm legs, the 30 degree angle, the butt height and how the screw eyes pass through the legs are ours. His drawing also marks parts E and G, which his text does not describe.

Malzemeler

4

Gerekli Aletler

10

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...