İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Trundle-and-Pitman Churn: One Crank Turns the Dasher Staff and Lifts It Up and Down at Once
Martin

Oluşturan

Martin

9. Kasım 2026NO
8
0
0
0
0

Trundle-and-Pitman Churn: One Crank Turns the Dasher Staff and Lifts It Up and Down at Once

Edward L. Dorsey of Greenwood, Indiana, received US 23,556, dated 12 April 1859, for giving a churn's dashers two motions at once. A crank turns a wheel with teeth on its face. The teeth work between the rounds of a trundle (lantern) wheel on the dasher staff and turn it, while a pin on the same wheel works a pitman that lifts and drops the staff. The staff carries a round dasher at its foot and an armed whipping dasher above; the up-and-down dasher keeps the cream from simply swirling round. This rung builds it in wood and steel rod on a square food container.
Orta
About 8 hours

Talimatlar

1

Two motions from one crank

Jupyter defteri yükleniyor…
2

A crank that lifts the dasher, before it

Rarey's crank only lifted the dasher. Dorsey's turns it as well, from the same wheel.
3

Read US 23,556

"... the teeth of wheel H work between the rounds n, n, n, of trundle wheel C, and give a circular motion to the said dashers. Thus the staff and dashers have two distinct motions—a vertical reciprocating and a rotary motion."
4

Body A, top and upright B

Use a square food-grade container about 300 x 300 x 320 mm. Cut an 18 mm plywood top 340 mm square with a 24 mm hole in the middle for the staff, and screw two cleats underneath so it sits square on the rim. Screw a hardwood upright B 44 x 44 mm, 300 mm tall, to the top, its near face 110 mm from the hole, and bore it 12.5 mm square to the top, 260 mm above it.

Bu adım için malzemeler:

Gıda sınıfı saklama kabıGıda sınıfı saklama kabı1 adet
Kontrplak levhaKontrplak levha1 adet
Sert Ağaç TahtasıSert Ağaç Tahtası1 adet
Ahşap vidalarAhşap vidalar10 adet
Ahşap TutkalıAhşap Tutkalı1 adet

Gerekli aletler:

El TesteresiEl Testeresi
Dekupaj TestereDekupaj Testere
Yassı matkap ucu takımıYassı matkap ucu takımı
Kablosuz MatkapKablosuz Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Tornavida takımıTornavida takımı
Şerit MetreŞerit Metre
5

Wheel H and shaft I

Cut an 18 mm plywood disc 300 mm across. Drill 36 holes 8 mm across, evenly round a 280 mm circle, and glue in 8 mm hardwood dowels standing 16 mm proud of the front face as the teeth. Drill an 8 mm hole 45 mm from the centre and press in an 8 mm steel pin 16 mm proud as pin o. Glue a hardwood hub 60 mm across on the back. Fix a 12 mm stainless rod through hub and disc with an M4 screw across as shaft I, pass it through the upright, and fix a hardwood crank D 132 mm long with a dowel handle on its far end.

Bu adım için malzemeler:

Kontrplak levhaKontrplak levha1 adet
Sert ağaç kavelalarSert ağaç kavelalar1 adet
Ahşap TutkalıAhşap Tutkalı1 adet
Paslanmaz çelik çubukPaslanmaz çelik çubuk1 adet
Sert Ağaç TahtasıSert Ağaç Tahtası1 adet
Makine vidalarıMakine vidaları2 adet
Naylon Fiberli Emniyet SomunuNaylon Fiberli Emniyet Somunu2 adet

Gerekli aletler:

Dekupaj TestereDekupaj Testere
Kablosuz MatkapKablosuz Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Demir TesteresiDemir Testeresi
Eğeler (El Eğesi)Eğeler (El Eğesi)
Zımpara KağıdıZımpara Kağıdı
Tornavida takımıTornavida takımı
6

Staff E, trundle C and dashers

Cut two hardwood heads M 74 mm across and 6 mm thick, bore each 20 mm in the middle and drill 8 holes 8 mm across on a 62 mm circle; glue in 8 dowel rounds n 116 mm long. Cut a 20 mm hardwood dowel 594 mm long as staff E and drill an 8.5 mm hole across it 14 mm below its top. Cut dasher J, an 18 mm plywood disc 200 mm across with six 28 mm holes, and dasher K, two plywood arms 230 x 24 mm halved into a cross. Glue J on the staff's foot, K 112 mm above it and the trundle where its middle meets the teeth with the staff halfway up its stroke.

Bu adım için malzemeler:

Sert Ağaç TahtasıSert Ağaç Tahtası1 adet
Sert ağaç kavelalarSert ağaç kavelalar1 adet
Kontrplak levhaKontrplak levha1 adet
Ahşap TutkalıAhşap Tutkalı1 adet

Gerekli aletler:

El TesteresiEl Testeresi
Dekupaj TestereDekupaj Testere
Kablosuz MatkapKablosuz Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Panç testere setiPanç testere seti
İşkencelerİşkenceler
Zımpara KağıdıZımpara Kağıdı
7

Pitman F

Bend an 8 mm stainless rod in the vise: a small eye at one end to go on pin o, then a straight length 80 mm from the eye's centre to a right-angle bend, then a leg 56 mm long that goes across through the hole in the staff's top as the pivot. Put the staff in through the top, set the eye on pin o with a washer and lock nut, and push the leg through the staff.

Bu adım için malzemeler:

Paslanmaz çelik çubukPaslanmaz çelik çubuk1 adet
Düz PulDüz Pul1 adet
Naylon Fiberli Emniyet SomunuNaylon Fiberli Emniyet Somunu1 adet

Gerekli aletler:

Tezgah MengenesiTezgah Mengenesi
Demir TesteresiDemir Testeresi
Eğeler (El Eğesi)Eğeler (El Eğesi)
Kurbağacık anahtarKurbağacık anahtar
8

The build in 3D

FreeCAD model of this build, the near half of the container cut away: the top and upright, wheel H with its dowel teeth and pin o, shaft I and crank D, the pitman bent into the staff's top, trundle C, and dashers K and J. It was checked for clashes at 12 crank positions through a full turn.
Tasarım DosyasıBLENDCC0 - Free
9

Churn

Lift the top, pour in about 12 litres of heavy cream at about 15 °C, checked with the thermometer, and set the top back. Turn the crank steadily and time it: the dashers turn and rise and fall together. When the butter comes, lift the top and staff out, pour off the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.

Bu adım için malzemeler:

Yağlı kremaYağlı krema12 l
İri Deniz Tuzuİri Deniz Tuzu1 adet
SuSu1 adet

Gerekli aletler:

Takılı kalan problu termometreTakılı kalan problu termometre
KronometreKronometre
Dijital Mutfak TerazisiDijital Mutfak Terazisi
Büyük paslanmaz çelik karıştırma kâsesiBüyük paslanmaz çelik karıştırma kâsesi
10

Troubleshooting

Trundle-and-pitman churn troubleshooting.

Flow

Loading...
11

History and honest limits

**Edward L. Dorsey** of Greenwood, Johnson County, Indiana, US 23,556, 12 April 1859, "Churn". He found it best in a square box, the rising and falling lower dasher checking the swirl the upper one gives. He claimed the trundle wheel, staff, pitman and cog wheel together. He gave no sizes or materials: every size and material here is ours.

Malzemeler

13

Gerekli Aletler

18

Tasarım dosyaları

1

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...