İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Smith's Fire Rake (Poker): a 3/8 in. Rod Drawn to a Flat Point, Crooked, and Looped Over the Anvil (Edwinson, 1886)
Forge

Oluşturan

Forge

14. Kasım 2026NO
9
0
0
0
0

Smith's Fire Rake (Poker): a 3/8 in. Rod Drawn to a Flat Point, Crooked, and Looped Over the Anvil (Edwinson, 1886)

The first job George Edwinson set his readers in Amateur Work (1886): the smith's rake for the forge fire, which "might be dubbed a poker". A yard of 3/8 in. iron rod drawn to a square then flat point with quarter turns, bent into a crook, and the other end bent round in three heats into a loop handle.
Başlangıç
An hour at the forge

Talimatlar

1

His sizes

Jupyter defteri yükleniyor…
2

Read Edwinson

"The rake, Fig. 16, might be dubbed a poker, and as this is the most simple tool, we will deal with that first."
3

Light a small fire

Pile slack round the tuyere, scoop a shallow pit in front of it, put in shavings with a few cinders on top, light and blow gently. Draw slack in until the heap glows, then damp the outside so the fire stays within 6 in. (15 cm) of the tuyere.

Bu adım için malzemeler:

Taş kömürüTaş kömürü1 adet

Gerekli aletler:

Demirci ocağıDemirci ocağı
4

Draw the point

Cut 36 in. (91 cm) of 3/8 in. (10 mm) iron rod with a cold chisel. Heat 2 in. of one end glowing white. On the outer edge of the anvil, hammer it lightly on the tip, giving the rod a quarter turn after each blow and drawing it back, to a square point. Strike only while it glows; reheat at a dull red. Next heat, round the corners and draw a flat tapering point (fig. 17).

Bu adım için malzemeler:

Dövme demir çubukDövme demir çubuk1 adet

Gerekli aletler:

Soğuk keskiSoğuk keski
Demirci ocağıDemirci ocağı
ÖrsÖrs
ÇekiçÇekiç
5

Crook the end

Heat the point to a dull red and bend it over the outer edge of the anvil with a few light blows into the crook (fig. 16).

Gerekli aletler:

Demirci ocağıDemirci ocağı
ÖrsÖrs
ÇekiçÇekiç
6

Bend the loop

Heat the rod about 10 in. from the other end to redness and bend it over the anvil edge (fig. 18). Heat 3 in. more of the bent part and shape it (fig. 19). Heat again and bring the end round to touch the shoulder (fig. 20), then shape the loop hot with light blows. (Experienced smiths scarf the end and weld it to the shoulder.)

Gerekli aletler:

Demirci ocağıDemirci ocağı
ÖrsÖrs
ÇekiçÇekiç
7

Troubleshooting

Rake troubleshooting.

Flow

Loading...
8

History and honest limits

From George Edwinson, "Smithing and Forging" II, **Amateur Work, Illustrated**, vol. V (1886), pp. 211-213 and figs. 15-20 (checked on the archive.org scan amateurworkillus05lond). Metric figures and the tools are ours.

Malzemeler

2

Gerekli Aletler

4

İlgili Blueprint'ler

Bu blueprint'ler bilgi paylaşır — teknikler, malzemeler veya ilkeler

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...