İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER

Sprung-Blade Inclined-Dasher Churn: The Blades Close to Pass the Narrow Top and Spread to Fill the Wide Bottom
John U. Fiester of Winchester, Ohio, received US 22,945 in February 1859 for a churn with a slanting dasher in a tub wider at the bottom than the top, so it is hard to tip over. The dasher's two blades are held to the spindle by a yoke spring and guided by pins in the slots of a cross tie: they close to pass the narrow top and spread to fill the wide bottom. Holes let the cream through the blades, and square pockets cut part way in carry air down into it.
This rung builds it in pine and hardwood with a crank.
Orta
About 8 hours, plus printing
Talimatlar
1
1
Tub, fill and the blades' reach
Tub, fill and the blades' reach
Jupyter defteri yükleniyor…
2
2
Holed beaters, before it
Holed beaters, before it
The Robies' beaters pass the cream through holes. Fiester's blades also have pockets that carry air down.
3
3
Read US 22,945
Read US 22,945
"... the yoke spring E and slots (a) allow the dasher blades to be forced easily into the smaller opening in the top of the tub, and when in to expand and fill the larger space at the bottom."
4
4
Print the journal box e
Print the journal box e
The block with the seat for the spindle's point. PETG, 0.2 mm layers, 40 % infill, 4 walls; wash before first use.
5
5
Print the yoke collar
Print the yoke collar
The collar on the spindle that holds the yoke spring. PETG, 0.2 mm layers, 40 % infill, 4 walls; wash before first use.
6
6
Tub A and lid B
Tub A and lid B
From 18 mm pine cut a floor 460 x 336 mm, two ends 400 mm wide at the foot, 320 mm at the top and 400 mm tall, and two sloping sides 336 mm wide that join them. Glue and screw the ends and sides on the floor so the tub is 400 mm wide inside at the floor and 320 mm at the top, 300 mm front to back. Cut a lid 374 x 336 mm with a turned dowel knob. Drill a 42 mm hole through the right side where the spindle meets it, about 345 mm above the inside floor.
Bu adım için malzemeler:
Çam tahta3 adet
Ahşap Tutkalı1 adet
Ahşap vidalar40 adet
Sert ağaç kavelalar1 adetGerekli aletler:
El Testeresi
Dekupaj Testere
Kablosuz Matkap
Panç testere seti
İşkenceler
İletki / Açı Ölçer
Zımpara Kağıdı
Tornavida takımı
Şerit Metre7
7
Spindle C and journal e
Spindle C and journal e
Cut a 40 mm hardwood dowel 641 mm long and whittle or plane one end to a point over 30 mm. Screw the journal box in the left corner of the floor, against the sloping side. Cut a half-lap notch 30 mm wide and 12 mm deep across the spindle 85 mm from its point for the cross tie.
Bu adım için malzemeler:
PETG filament1 adet
Sert ağaç kavelalar1 adet
Ahşap vidalar4 adetGerekli aletler:
FDM 3B yazıcı
El Testeresi
Marangoz keskileri
Eğeler (El Eğesi)
Tornavida takımı8
8
Blades D, tie F and yoke E
Blades D, tie F and yoke E
Draw an oval 340 x 220 mm on 16 mm hardwood and cut it in two along its length, then take 4 mm off each straight edge so the halves clear the spindle. Drill four 20 mm holes f in each blade and chisel four 20 mm square pockets d, 8 mm deep with bevelled sides, facing the same way. Glue a 9 mm dowel pin b into each blade 31 mm from its straight edge, 30 mm from its lower end. Cut a hardwood cross tie F 190 x 30 x 16 mm with a 10 mm slot 30 mm long near each end, glue it into the spindle's notch, and drop the pins into its slots. Slide the collar onto the spindle above the blades and screw two spring steel strips 15 x 1.5 mm, 42 mm long, from the collar to each blade's top end.
Bu adım için malzemeler:
Sert Ağaç Tahtası1 adet
Sert ağaç kavelalar1 adet
Ahşap Tutkalı1 adet
Yay çeliği şeridi1 adet
Makine vidaları8 adet
Naylon Fiberli Emniyet Somunu8 adetGerekli aletler:
Dekupaj Testere
Kablosuz Matkap
Yassı matkap ucu takımı
Marangoz keskileri
Demir Testeresi
Eğeler (El Eğesi)
Zımpara Kağıdı
Tornavida takımı9
9
Fit the dasher and crank
Fit the dasher and crank
Pass the spindle's top out through the hole in the right side, squeeze the blades together through the tub's top and let them spread, and seat the point in the journal box. Fix a hardwood crank arm 130 mm long on the spindle outside the tub with a screw across, and glue in a 24 mm dowel handle 100 mm long.
Bu adım için malzemeler:
Sert Ağaç Tahtası1 adet
Sert ağaç kavelalar1 adet
Ahşap Tutkalı1 adet
Ahşap vidalar1 adetGerekli aletler:
El Testeresi
Kablosuz Matkap
Yassı matkap ucu takımı
Tornavida takımı10
10
The build in 3D
The build in 3D
FreeCAD model of this build, the near half of the tub cut away: the sloping tub, the journal box, the slanting spindle with its two holed blades, the cross tie with its slots and pins, the yoke collar and springs, and the crank outside.
11
11
Churn
Churn
Pour in about 12 litres of heavy cream at about 15 °C, checked with the thermometer, and put the lid on. Turn the crank steadily and time it: the blades dip in and out of the cream, the pockets carrying air down. When the butter comes, pour off the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.
Bu adım için malzemeler:
Yağlı krema12 l
İri Deniz Tuzu1 adet
Su1 adetGerekli aletler:
Takılı kalan problu termometre
Kronometre
Dijital Mutfak Terazisi
Büyük paslanmaz çelik karıştırma kâsesi12
12
Troubleshooting
Troubleshooting
Sprung-blade churn troubleshooting.
Flow
Loading...
13
13
History and honest limits
History and honest limits
**John U. Fiester** of Winchester, Guernsey County, Ohio, US 22,945, "Churn": the drawing reads 15 February 1859, the text 25 February 1859. A tub wider at the top can be overset; his is wider at the bottom, and the sprung, guided blades still fill it. He claimed the adjustable dasher with its yoke spring, slotted cross tie and pins, holes and air pockets. He gave no sizes or materials: ours are a pine tub, hardwood dasher and steel springs.
Malzemeler
12- 3 adetYer Tutucu
- 3 adetYer Tutucu
- 45 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 8 adetYer Tutucu
- Yer Tutucu
- 12 lYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
Gerekli Aletler
18- Yer Tutucu
- 1 vendor sell this, none ship to you yetYer Tutucu
- 1 vendor sell this, none ship to you yetYer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- 1 vendor sell this, none ship to you yetYer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
Tasarım dosyaları
3Bu planla yapılan
İlgili Blueprint'ler
Bu blueprint'ler bilgi paylaşır — teknikler, malzemeler veya ilkeler
CC0 Kamu Malı
Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.
Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.



