İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER

Rocking Bucket-Dasher Churn: A Crank and Rod Rock a Dasher of Bucketed Arms, a Fixed Bucket Breaks the Current
Gillett Bunting of Liberty, Indiana, received US 26,226, dated 22 November 1859, for a churn-dasher. A dasher of crossed arms with buckets on their ends rocks on a level shaft whose bearings slide up or down to suit the amount of cream. A crank above, turned through a pair of cog wheels with a balance wheel, rocks it by a long rod, throwing the cream into opposing currents, and a fixed bucket on the bottom breaks the current along the floor.
The patent gives no sizes; every size here is ours.
Orta
About 2 days, plus printing
Talimatlar
1
1
How far the dasher rocks
How far the dasher rocks
Jupyter defteri yükleniyor…
2
2
Agitators swung on pivots, two weeks before
Agitators swung on pivots, two weeks before
Cooper swings his agitators from a dash rod worked by hand. Bunting rocks a whole dasher from a crank.
3
3
Read US 26,226
Read US 26,226
"the rapid oscillating motion thus imparted to the dasher, through the medium of buckets (e' g', K) forces the cream into violent opposing currents, at the same time, the concussive action of the buckets (e', g') and arms (e, g) and bar (E) upon the cream is fully developed, thereby producing, a rapid and violent agitation of the cream"
4
4
Print the driving wheel G
Print the driving wheel G
Spur wheel, 48 teeth, module 3, 15 mm face, with a hub bored 20.6 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
5
5
Print the wheel h
Print the wheel h
Spur pinion, 16 teeth, module 3, 15 mm face, with a hub bored 12.6 mm and a cross hole for a pin. PETG, 0.2 mm layers, 40 % infill, 4 walls.
6
6
Shell A, bed A', guides L and bucket K
Shell A, bed A', guides L and bucket K
Use a wooden tub 360 mm across inside at the floor, 320 mm at the top and 420 mm deep. Stand it on a bed board 520 x 560 mm between two guide strips. Glue and screw a hardwood block K, 60 x 300 x 60 mm, across the middle of the floor, with a 24 x 24 mm socket 50 mm deep near each end for the slides. Fill the tub with water overnight so it swells tight, then empty it.
Bu adım için malzemeler:
Ahşap tekne1 adet
Sert Ağaç Tahtası2 adet
Ahşap Tutkalı1 adet
Ahşap vidalar12 adetGerekli aletler:
Daire testere tezgâhı
El Testeresi
Zıvana yuvası kalemi
Ahşap Tokmak
Kablosuz Matkap
Matkap Ucu Takımı
Çubuklu işkence
Şerit Metre
Su7
7
Slides f and the dasher
Slides f and the dasher
Cut two slides 20 x 24 mm, 255 mm long, bore each 21 mm 225 mm from its foot for the shaft's journal, and a row of 6 mm holes near the foot for a set screw through the block K. Make the shaft F a 20 mm hardwood dowel 280 mm long. Mortise through it two arms e 20 x 30 mm, 210 mm long, 150 mm apart, two arms g 20 x 30 mm, 260 mm long, at right angles to them, 80 mm apart, and the bar E 20 x 30 mm, 235 mm long, between the arms e, its long end reaching 100 mm past the shaft and bored 12.6 mm. Screw three U-channel buckets 170 x 40 x 20 mm of hardwood across the ends: one on the arms e and E's short end, one on each end of the arms g. Stand the slides in K with the shaft's ends in them, 240 mm up.
Bu adım için malzemeler:
Sert Ağaç Tahtası2 adet
Sert ağaç kavelalar1 adet
Ahşap Tutkalı1 adet
Ahşap vidalar24 adet
Altıköşe cıvata takımı2 adetGerekli aletler:
Daire testere tezgâhı
Freze motoru
Zıvana yuvası kalemi
Ahşap Tokmak
Kablosuz Matkap
Matkap Ucu Takımı
Zımpara Kağıdı
Şerit Metre8
8
Frame B, crank shaft C, wheels and rod D
Frame B, crank shaft C, wheels and rod D
Bolt two posts of 40 x 30 mm hardwood to the bed beside the tub, 400 mm apart, 850 mm tall, and bore them 12.6 mm 690 mm above the tub's floor. Bend a 12 mm stainless shaft C into a crank of 50 mm throw in its middle, heating the bends red with the torch, and run it through the posts over the bar E's end. Pin the wheel h on one end and a hardwood balance wheel k, 260 mm across and 30 mm thick, on the other. Fix a 20 mm stud above h for the wheel G, meshing, with a crank handle H. Join the crank to E's end with a hardwood rod D, 450 mm between its pins.
Bu adım için malzemeler:
Yumuşak ağaç 70x70 mm1 adet
Sert Ağaç Tahtası2 adet
Paslanmaz çelik çubuk2 adet
Shaft Collar2 adet
Kopilya4 adet
Düz Pul6 adet
Altıköşe cıvata takımı4 adet
Naylon Fiberli Emniyet Somunu4 adet
PETG filament1 adetGerekli aletler:
FDM 3B yazıcı
Propan Pürmüz
Tezgah Mengenesi
Çekiç
Isıya Dayanıklı Eldiven
Dekupaj Testere
Pusula
Demir Testeresi
Eğeler (El Eğesi)
Kablosuz Matkap
Matkap Ucu Takımı
Kurbağacık anahtar9
9
The build in 3D
The build in 3D
FreeCAD model of this build, the tub cut through the middle: the bed and guides, the fixed bucket K with the two slides, the dasher with its arms, bar E and three buckets, the rod D up to the cranked shaft C, the wheels G and h, the crank H and the balance wheel. The crank was turned through 24 positions.
10
10
Churn
Churn
Pour in heavy cream at about 15 °C, checked with the thermometer; for less cream, lower the slides in K so the dasher still works in it. Turn the crank H steadily, timing it. When the butter comes, lift the rod off the crank and the dasher out on its slides, take out the butter, drain the buttermilk, wash the butter in cold water until it runs clear, salt and weigh it.
Bu adım için malzemeler:
Yağlı krema15 l
İri Deniz Tuzu1 adet
Su1 adetGerekli aletler:
Takılı kalan problu termometre
Kronometre
Dijital Mutfak Terazisi
Büyük paslanmaz çelik karıştırma kâsesi11
11
Troubleshooting
Troubleshooting
Rocking dasher troubleshooting.
Flow
Loading...
12
12
History and honest limits
History and honest limits
**Gillett Bunting** of Liberty, Union County, Indiana, assignor to himself and W. M. Jarrell, US 26,226, 22 November 1859, "Churn-Dasher". He disclaimed hinged churn-dashers and oscillating movement as such, and claimed the vibrating movement of the dasher by the arms with the crank, driving wheel and connecting rod, with the current breaker K. The patent gives no sizes; every size here is ours. His frame B stands on the shell's top; ours is two posts on the bed beside it.
Malzemeler
16- 1 adetYer Tutucu
- 2 adetYer Tutucu
- 2 adetYer Tutucu
- 36 adetYer Tutucu
- 1 adetYer Tutucu
- 6 adetYer Tutucu
- 1 adetYer Tutucu
- 2 adetYer Tutucu
- 2 adetYer Tutucu
- 4 adetYer Tutucu
- 6 adetYer Tutucu
- Yer Tutucu
- 1 adetYer Tutucu
- 15 lYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
Gerekli Aletler
25- 1 vendor sell this, none ship to you yetYer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- 1 vendor sell this, none ship to you yetYer Tutucu
- Yer Tutucu
- Yer Tutucu
- 1 vendor sell this, none ship to you yetYer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- 1 vendor sell this, none ship to you yetYer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
Tasarım dosyaları
3Bu planla yapılan
İlgili Blueprint'ler
Bu blueprint'ler bilgi paylaşır — teknikler, malzemeler veya ilkeler

Folding-Lever Dasher Churn: The Dash Rod Folds Two Levers and Swings the Agitators Side to Side
Buttercup tarafından
Ağaç işleri
9
0
0
0
0
0

Segmental-Stave Churn: Thick Curved Staves Split the Cream's Current, a Long Blade Sweeps Beneath Them
Buttercup tarafından
Ağaç işleri
7
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
TheChef tarafından
ZANAAT
63
0
0
0
0
0
CC0 Kamu Malı
Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.
Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

