İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Sliding-Strip Cylinder Dash Churn: Strips on the Slats Open the Gaps One Way and Close Them the Other
Buttercup

Oluşturan

Buttercup

10. Kasım 2026IE
8
0
0
0
0

Sliding-Strip Cylinder Dash Churn: Strips on the Slats Open the Gaps One Way and Close Them the Other

Daniel K. France of Congress, Ohio, received US 25,404, dated 13 September 1859, for a cylindrical churn-dash. Two crosses of curved arms carry four groups of three slats, each slat half by one inch. On each group a metal strip with a slot down its middle is held by screws in short slots, so it slides when the dash changes direction and opens or closes the spaces between the slats. Turned one way the dash churns; reversed, it gathers the butter into a corner. Two cog wheels at three to one drive it. France gives one size, the slats; every other size here is ours.
Orta
About 2 days, plus printing

Talimatlar

1

France's slats, and the wheels' three to one

Jupyter defteri yükleniyor…
2

A turning dasher on crossed arms in a box, before it

That dasher's boards were fixed. France's slats carry strips that open and close the gaps with the turning.
3

Read US 25,404

"The motion of the dash to be to the left in the direction of the curve of the arms while churning, thereby producing the greatest amount of friction in the cream. When butter is produced the motion of the dash is reversed and the butter gathered in the lower left corner of the churn by the reversed action thereon of the dash and self adjusting slide."
4

Print the large cog wheel

The 48-tooth spur wheel (module 3) with a hub, bored 20.4 mm, for the crank's stud. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Tasarım DosyasıSTLCC0 - Free
5

Print the small cog wheel

The 16-tooth spur pinion (module 3) with a hub, bored 20.4 mm, for the dash's shaft. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Tasarım DosyasıSTLCC0 - Free
6

Box with legs and lid

From 20 mm hardwood cut a bottom 440 x 340 mm, two sides 440 x 300 mm, two ends 300 x 300 mm and a lid 440 x 340 mm. Bore each end 20.8 mm through its middle, 150 mm above the floor, for the shaft. Glue and screw the ends between the sides and the box onto the bottom, and screw four legs of 70 mm timber, 350 mm long, under it. Fill the box with water overnight so it swells tight, then empty it.

Bu adım için malzemeler:

Sert Ağaç TahtasıSert Ağaç Tahtası3 adet
Yumuşak ağaç 70x70 mmYumuşak ağaç 70x70 mm1 adet
Ahşap TutkalıAhşap Tutkalı1 adet
Ahşap vidalarAhşap vidalar30 adet

Gerekli aletler:

Daire testere tezgâhıDaire testere tezgâhı
El TesteresiEl Testeresi
Kablosuz MatkapKablosuz Matkap
Yassı matkap ucu takımıYassı matkap ucu takımı
Çubuklu işkenceÇubuklu işkence
Marangoz gönyesiMarangoz gönyesi
Şerit MetreŞerit Metre
SuSu
7

Dash: arms, hubs and slats

Cut eight curved arms from 22 mm hardwood with the jigsaw, each 18 mm wide, sweeping 30 degrees from a 20 mm hub radius out to 112 mm. Glue four into a 56 mm hardwood hub to make a cross, twice, all curving the same way, and bore the hubs 20.4 mm. Cut twelve slats 12.7 x 25.4 mm, 340 mm long, and screw them to the arms' ends in groups of three, 9 mm apart, flat side out, so their faces are 125 mm from the middle.

Bu adım için malzemeler:

Sert Ağaç TahtasıSert Ağaç Tahtası1 adet
Ahşap TutkalıAhşap Tutkalı1 adet
Ahşap vidalarAhşap vidalar24 adet

Gerekli aletler:

Dekupaj TestereDekupaj Testere
Daire testere tezgâhıDaire testere tezgâhı
Kablosuz MatkapKablosuz Matkap
Yassı matkap ucu takımıYassı matkap ucu takımı
Matkap Ucu TakımıMatkap Ucu Takımı
Şerit MetreŞerit Metre
8

Strips B with slots C and screws D

Cut four strips of 0.8 mm stainless sheet, 324 mm long and as wide as a group of slats (94 mm). Cut a slot C 9 mm wide along the middle of each, stopping 30 mm from the ends, and a short slot across each end. Lay each strip on its group's outer face and fix it with an M4 screw through each end slot into the arm's end, just loose enough to slide sideways. Turned one way, the cream pushes each strip so its slot lies over the slats; the other way, over a space.

Bu adım için malzemeler:

Paslanmaz çelik levhaPaslanmaz çelik levha1 adet
Makine vidalarıMakine vidaları8 adet
Düz PulDüz Pul8 adet

Gerekli aletler:

Sac makasıSac makası
Eğeler (El Eğesi)Eğeler (El Eğesi)
Kablosuz MatkapKablosuz Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Tornavida takımıTornavida takımı
9

Shaft, cog wheels and crank

Pass a 20 mm stainless shaft through one end of the box, the two hubs and the other end, and pin the hubs to it. On the outside of the geared end, screw a hardwood block 96 mm above the shaft, fix a 20 mm stud in it, and fit the large wheel on the stud with a crank and handle. Pin the small wheel on the shaft's end meshing with it.

Bu adım için malzemeler:

Paslanmaz çelik çubukPaslanmaz çelik çubuk2 adet
Sert Ağaç TahtasıSert Ağaç Tahtası1 adet
Sert ağaç kavelalarSert ağaç kavelalar1 adet
Altıköşe cıvata takımıAltıköşe cıvata takımı3 adet
Naylon Fiberli Emniyet SomunuNaylon Fiberli Emniyet Somunu3 adet
PETG filamentPETG filament1 adet

Gerekli aletler:

FDM 3B yazıcıFDM 3B yazıcı
Demir TesteresiDemir Testeresi
Kablosuz MatkapKablosuz Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Kurbağacık anahtarKurbağacık anahtar
10

The build in 3D

FreeCAD model of this build, front side cut away: the dash's two crosses of curved arms, the four groups of slats with their strips, slots and screws, the shaft through the box's ends, and the two cog wheels and crank outside. The dash was turned through 16 angles.
Tasarım DosyasıBLENDCC0 - Free
11

Churn, then gather

Pour about 6 litres of heavy cream at about 15 °C into the box, checked with the thermometer, and put the lid on. Turn the crank so the dash turns with the curve of its arms, timing it. When the butter comes, turn the crank the other way so the strips slide over and the dash gathers the butter into a corner. Lift it out, drain the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.

Bu adım için malzemeler:

Yağlı kremaYağlı krema6 l
İri Deniz Tuzuİri Deniz Tuzu1 adet
SuSu1 adet

Gerekli aletler:

Takılı kalan problu termometreTakılı kalan problu termometre
KronometreKronometre
Dijital Mutfak TerazisiDijital Mutfak Terazisi
Büyük paslanmaz çelik karıştırma kâsesiBüyük paslanmaz çelik karıştırma kâsesi
12

Troubleshooting

Sliding-strip churn troubleshooting.

Flow

Loading...
13

History and honest limits

**Daniel K. France** of Congress, Wayne County, Ohio, US 25,404, 13 September 1859, "Churn-Dash". He claimed the metallic strips B on the convex surface of the slats, held by slots and screws. He disclaimed slats or beaters hinged to the arms. His slats, half by one inch, are kept; every other size is ours. His plates A, changed to reverse the dash when the crank is used alone, are not built.

Malzemeler

15

Gerekli Aletler

20

Tasarım dosyaları

3

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...