İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER

Twin-Crank Slide-Top Churn: Two Dashers on a Bent Crank Shaft, Sliding Plates Keep the Milk In
Cable L. Gilpatrick of Saco, Maine, received US 25,405, dated 13 September 1859, for a churn. A crank shaft bent into two opposite cranks rides on two posts above a box and works two dashers, so one goes down as the other comes up. Each dasher is two boards crossed and bored with holes. The staffs pass through holes in two slides that move in casings on the top, following the staffs so the milk cannot splash out.
The patent gives no sizes; every size here is ours.
Orta
About 2 days, plus printing
Talimatlar
1
1
One up, one down
One up, one down
Jupyter defteri yükleniyor…
2
2
Two dashers in one box, a few weeks before
Two dashers in one box, a few weeks before
Campbell rocked his two dashers on a lever. Gilpatrick drives his from a bent crank shaft and covers the top with slides.
3
3
Read US 25,405
Read US 25,405
"Motion is then communicated to the dashers by means of the crank-shaft. As one dasher descends, the other ascends. Thus the milk is kept in contant agitation, which is necessary in order to churn expeditiously. The slides being operated upon by the dasher-staffs prevents the milk from splashing out, as it otherwise would do."
4
4
Print the staff collars
Print the staff collars
Each collar is two halves round a crank pin: the lower half with a 30 mm square socket for the staff, and a cap; two M5 screws close them. Print two sets. PETG, 0.2 mm layers, 40 % infill, 4 walls.
5
5
Box A and its posts
Box A and its posts
From 20 mm hardwood make a box 400 x 360 mm and 450 mm deep inside, with a bottom. Make the two 400 mm sides 170 mm taller, narrowed to posts 120 mm wide above the box, and bore each post 13 mm, 600 mm above the bottom's underside, for the shaft. Glue and screw a cleat 20 mm square along the inside of each post side, 30 mm below the rim, for the top. Fill the box with water overnight so it swells tight, then empty it.
Bu adım için malzemeler:
Sert Ağaç Tahtası3 adet
Ahşap Tutkalı1 adet
Ahşap vidalar30 adetGerekli aletler:
Daire testere tezgâhı
El Testeresi
Kablosuz Matkap
Matkap Ucu Takımı
Çubuklu işkence
Marangoz gönyesi
Şerit Metre
Su6
6
Crank shaft D and crank E
Crank shaft D and crank E
Cut 12 mm stainless rod about 750 mm long. Heat each bend red with the torch and bend it in the vise into two cranks of 50 mm throw, pointing opposite ways, each crank pin 50 mm long, their middles 180 mm apart. Check the journals line up by rolling the shaft on the bench. Thread one end through a post, the collars' lower halves onto the pins, and the other end through the other post. Fix a hardwood crank E, 160 mm long with a handle, on the end that sticks out.
Bu adım için malzemeler:
Paslanmaz çelik çubuk1 adet
Sert Ağaç Tahtası1 adet
Sert ağaç kavelalar1 adet
Ahşap Tutkalı1 adetGerekli aletler:
Propan Pürmüz
Tezgah Mengenesi
Çekiç
Isıya Dayanıklı Eldiven
Demir Testeresi
Eğeler (El Eğesi)
Kablosuz Matkap
Matkap Ucu Takımı
Şerit Metre7
7
Top A', casings F and slides H
Top A', casings F and slides H
Cut the top to drop onto the cleats, with two slots 140 x 50 mm across it, under the cranks, and a finger hole. Over each slot build a casing F: two rails 20 x 26 mm, 370 mm long, 80 mm apart, with a strip on each that overhangs the inside by 8 mm, and an end block at each end, leaving 346 mm inside. Cut each slide H 240 x 79 mm from 18 mm hardwood, so it slides under the strips, with a hole 34 mm square in its middle, 4 mm bigger than the staff.
Bu adım için malzemeler:
Sert Ağaç Tahtası2 adet
Ahşap Tutkalı1 adet
Ahşap vidalar24 adetGerekli aletler:
Daire testere tezgâhı
Freze motoru
Zıvana yuvası kalemi
Ahşap Tokmak
Kablosuz Matkap
Matkap Ucu Takımı
Zımpara Kağıdı
Çubuklu işkence8
8
Staffs B and dashers C
Staffs B and dashers C
Cut two staffs 30 mm square, 480 mm long. For each dasher, half-lap two boards 180 x 50 x 15 mm into a cross, bore eight 12 mm holes, cut a 30 mm square hole in the middle, and glue the staff's end into it. Set the top on its cleats, pass each staff up through its slide's hole, and bolt the collar's cap over its pin and onto the staff's top, turning the cross so its arms point to the box's corners.
Bu adım için malzemeler:
Sert Ağaç Tahtası1 adet
Ahşap Tutkalı1 adet
Makine vidaları4 adet
Düz Pul4 adet
Naylon Fiberli Emniyet Somunu4 adet
PETG filament1 adetGerekli aletler:
FDM 3B yazıcı
Daire testere tezgâhı
Zıvana yuvası kalemi
Ahşap Tokmak
Kablosuz Matkap
Matkap Ucu Takımı
Tornavida takımı
Zımpara Kağıdı9
9
The build in 3D
The build in 3D
FreeCAD model of this build, one side and the lower part of one post cut away: the box, the bent crank shaft on its posts with crank E, the two staffs in their collars, the dashers, and the slides in their casings on the top. The crank was turned through 24 positions.
10
10
Churn
Churn
Lift the collars' caps off, take out the top, pour in about 15 litres of heavy cream at about 15 °C, checked with the thermometer, and put the top and caps back. Turn the crank steadily, timing it. When the butter comes, take the top out, lift out the butter, drain the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.
Bu adım için malzemeler:
Yağlı krema15 l
İri Deniz Tuzu1 adet
Su1 adetGerekli aletler:
Takılı kalan problu termometre
Kronometre
Dijital Mutfak Terazisi
Büyük paslanmaz çelik karıştırma kâsesi
Tornavida takımı11
11
Troubleshooting
Troubleshooting
Twin-crank churn troubleshooting.
Flow
Loading...
12
12
History and honest limits
History and honest limits
**Cable L. Gilpatrick** of Saco, Maine, US 25,405, 13 September 1859, "Churn". He claimed the crank shaft D and staffs B with the top A', "when said top is provided with boxes (F,) in which play slides, through which the staffs pass". The patent gives no sizes; every size here is ours. His collars are not described beyond "passing around said cranks"; ours are printed and split so the top can come out.
Malzemeler
12- 3 adetYer Tutucu
- 4 adetYer Tutucu
- 54 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 4 adetYer Tutucu
- 4 adetYer Tutucu
- Yer Tutucu
- 1 adetYer Tutucu
- 15 lYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
Gerekli Aletler
24- 1 vendor sell this, none ship to you yetYer Tutucu
- Yer Tutucu
- 1 vendor sell this, none ship to you yetYer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- 1 vendor sell this, none ship to you yetYer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
Tasarım dosyaları
2Bu planla yapılan
İlgili Blueprint'ler
Bu blueprint'ler bilgi paylaşır — teknikler, malzemeler veya ilkeler

Hinged-Float Double-Dasher Churn: Floats That Close Going Down and Fall Open Coming Up
Buttercup tarafından
Ağaç işleri
8
0
0
0
0
0

Star-Dasher Crank Churn: Geared Crank and Flywheel Drive Two Notched Dashers Set Point Over Gap
Martin tarafından
Ağaç işleri
13
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
TheChef tarafından
ZANAAT
63
0
0
0
0
0
CC0 Kamu Malı
Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.
Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

