İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Star-Dasher Crank Churn: Geared Crank and Flywheel Drive Two Notched Dashers Set Point Over Gap
Martin

Oluşturan

Martin

9. Kasım 2026NO
13
0
0
0
0

Star-Dasher Crank Churn: Geared Crank and Flywheel Drive Two Notched Dashers Set Point Over Gap

Lorenzo Lake of Middlebury, Pennsylvania, received US 24,845, dated 19 July 1859, for an upright dash churn worked by gearing so that a child could churn even a very large churn. A handle turns a large wheel driving a wheel half its size on a crank shaft with a balance wheel; the crank's pitman works the staff up and down through a guide. The staff carries two dashers of boards with V-shaped slots in their ends, set so the points of one lie over the gaps of the other, cutting the cream as it escapes going down and up and dashing it against the sides. This rung builds it with printed gears over a 20-litre bucket.
Orta
About 2 days, plus printing

Talimatlar

1

Strokes per turn of the handle

Jupyter defteri yükleniyor…
2

A crank and pitman working the staff, before it

Dorsey's pitman also turned the staff. Lake's only lifts it, through gearing and a balance wheel for speed.
3

Read US 24,845

"... these dashers are so placed upon the staff that the sharpened ends of the boards thus cut, will cover the spaces left between the boards in the dasher immediately above or below—so that when operated in the churn the cream will be more thoroughly cut and the globules will be more easily and speedily broken."
4

Print the wheel E

The 40-tooth wheel for the handle's shaft. PETG, 0.2 mm layers, 50 % infill, 5 walls.
Tasarım DosyasıSTLCC0 - Free
5

Print the wheel F

The 20-tooth wheel for the crank shaft. PETG, 0.2 mm layers, 50 % infill, 5 walls.
Tasarım DosyasıSTLCC0 - Free
6

Platform, upright and frame

Screw a pine platform C 500 x 550 mm. Stand a 70 mm upright C' 990 mm tall at its back, braced. Screw a hardwood beam 130 x 255 x 40 mm out from the upright's top toward the front, and hang three hardwood blocks from it, each bored 20.5 mm 900 mm above the floor: two either side of the crank, 90 mm apart, for shaft G, and one 90 mm to the side for wheel E's shaft. Screw a hardwood guide arm I from the upright to over the bucket 430 mm up, with a 26 mm square hole.

Bu adım için malzemeler:

Çam tahtaÇam tahta2 adet
Yumuşak ağaç 70x70 mmYumuşak ağaç 70x70 mm2 adet
Sert Ağaç TahtasıSert Ağaç Tahtası2 adet
#10 x 3" ahşap vidası#10 x 3" ahşap vidası20 adet
Ahşap TutkalıAhşap Tutkalı1 adet

Gerekli aletler:

El TesteresiEl Testeresi
Kablosuz MatkapKablosuz Matkap
Yassı matkap ucu takımıYassı matkap ucu takımı
Marangoz keskileriMarangoz keskileri
Su TerazisiSu Terazisi
Şerit MetreŞerit Metre
7

Crank shaft G, wheels and handle

Make the crank from two hardwood webs 30 x 10 mm, a 12 mm stainless pin 50 mm off the axis between them, and two 20 mm steel stubs, one each side, run through the hanging blocks. Fix wheel F on the rear stub and a plywood balance wheel B 300 mm across, with spokes, on the front stub. Run a 20 mm steel shaft through the third block with wheel E meshing with F, and a hardwood handle M 57 mm long with a dowel grip on its end.

Bu adım için malzemeler:

Sert Ağaç TahtasıSert Ağaç Tahtası1 adet
Paslanmaz çelik çubukPaslanmaz çelik çubuk1 adet
Ham çelik çubukHam çelik çubuk2 adet
PETG filamentPETG filament1 adet
Kontrplak levhaKontrplak levha1 adet
Sert ağaç kavelalarSert ağaç kavelalar1 adet
Ahşap TutkalıAhşap Tutkalı1 adet
Altıköşe cıvata takımıAltıköşe cıvata takımı4 adet
Naylon Fiberli Emniyet SomunuNaylon Fiberli Emniyet Somunu4 adet

Gerekli aletler:

FDM 3B yazıcıFDM 3B yazıcı
Dekupaj TestereDekupaj Testere
Demir TesteresiDemir Testeresi
Kablosuz MatkapKablosuz Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Eğeler (El Eğesi)Eğeler (El Eğesi)
Kurbağacık anahtarKurbağacık anahtar
8

Staff, dashers and pitman

Cut two plywood dashers L, each a 16-point star 250 mm across with its notches 20 mm deep, and a 25 mm square hole in the middle. Glue them on a 25 mm square hardwood staff D 150 mm apart, the upper turned half a point from the lower. Cut a hardwood pitman H 300 mm between centres with a fork at its foot; fit a hardwood thimble J on the staff's top and push an 8 mm stainless rod a through the fork, thimble and staff. Put the staff through the guide and the bucket's lid and set the lower dasher 25 mm off the floor at the bottom of the stroke.

Bu adım için malzemeler:

Kontrplak levhaKontrplak levha1 adet
Sert Ağaç TahtasıSert Ağaç Tahtası2 adet
Ahşap TutkalıAhşap Tutkalı1 adet
Paslanmaz çelik çubukPaslanmaz çelik çubuk1 adet
Düz PulDüz Pul2 adet
20 Litrelik Kova20 Litrelik Kova1 adet

Gerekli aletler:

Dekupaj TestereDekupaj Testere
El TesteresiEl Testeresi
Marangoz keskileriMarangoz keskileri
Kablosuz MatkapKablosuz Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Zımpara KağıdıZımpara Kağıdı
9

The build in 3D

FreeCAD model of this build, half the bucket cut away: the platform and upright, the beam with its hanging blocks, the split crank shaft with balance wheel and wheel F, wheel E and handle M, the forked pitman and thimble, the staff through its guide, and the two star dashers. It was checked at eight crank angles.
Tasarım DosyasıBLENDCC0 - Free
10

Churn

Pour about 10 litres of heavy cream at about 15 °C into the bucket, checked with the thermometer, and put the lid on round the staff. Turn the handle steadily and time it. When the butter comes, pull pin a, lift the staff out, pour off the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.

Bu adım için malzemeler:

Yağlı kremaYağlı krema10 l
İri Deniz Tuzuİri Deniz Tuzu1 adet
SuSu1 adet

Gerekli aletler:

Takılı kalan problu termometreTakılı kalan problu termometre
KronometreKronometre
Dijital Mutfak TerazisiDijital Mutfak Terazisi
Büyük paslanmaz çelik karıştırma kâsesiBüyük paslanmaz çelik karıştırma kâsesi
11

Troubleshooting

Star-dasher churn troubleshooting.

Flow

Loading...
12

History and honest limits

**Lorenzo Lake** of Middlebury, Tioga County, Pennsylvania, assignor to himself and William Patton of Towanda, US 24,845, 19 July 1859, "Churn". He claimed the dasher L worked by the devices described, not the gearing as such. His only proportion is wheel F about half wheel E. His dashers are boards with V-slotted ends; ours are plywood stars cut to the same pattern. Every size is ours.

Malzemeler

17

Gerekli Aletler

17

Tasarım dosyaları

3

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...