İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
A Set of Cold Chisels: Flat, Gouge, Side, Cape, Diamond-Point and Round-Nose, Edge Hardened Only, Tempered Purple (Griswold, 1904)
Forge

Oluşturan

Forge

14. Kasım 2026NO
11
0
0
0
0

A Set of Cold Chisels: Flat, Gouge, Side, Cape, Diamond-Point and Round-Nose, Edge Hardened Only, Tempered Purple (Griswold, 1904)

Robert Gibson Griswold's working set of cold chisels from Amateur Work (Boston, 1904): octagonal tool steel or old files forged about 5 in. long, flat chisels 3/8 to 1 in. with a 60 degree edge, plus gouges, side, cape, diamond-point and round-nose chisels; only the last 1/8 in. of the edge hardened, tempered light purple for steel or dark purple for iron.
Orta
Two or three days for the set

Talimatlar

1

His sizes

Jupyter defteri yükleniyor…
2

Read Griswold

"When the tool is forged the edge only must be hardened for about 1/8 in., the metal above being left softer to withstand the shock."
3

Forge the blanks

From octagonal tool steel (or old files) forge each chisel about 5 in. (127 mm) from head to edge with a gradual taper to the edge, and forge the head down so it does not broom. Forging steps are ours: forge at a bright red only, as in his part I.

Bu adım için malzemeler:

Sekizgen takım çeliği çubukSekizgen takım çeliği çubuk1 adet

Gerekli aletler:

Demirci ocağıDemirci ocağı
ÖrsÖrs
ÇekiçÇekiç
Demirci kerpeteniDemirci kerpeteni
4

Shape the edges

Flat chisels 3/8, 1/2, 5/8 and 1 in. wide; gouges 1/4-5/8 in. with the bevel inside; side chisels 1/4, 3/8, 1/2 in. with the edge in one flat side; cape chisels 3/16 and 1/4 in. with the stock behind slightly thinner; a diamond point about 1/8 in. on the square (bent version for flat work); round-nose chisels, heavy and a long-tapered drawing chisel (his fig. 1).

Gerekli aletler:

Demirci ocağıDemirci ocağı
ÖrsÖrs
ÇekiçÇekiç
Eğeler (El Eğesi)Eğeler (El Eğesi)
5

Harden the edge only

Heat the edge and harden only about 1/8 in. (3 mm) of it in water, leaving the body softer: a chisel hard too far up cracks off on a line under a heavy blow.

Bu adım için malzemeler:

SuSu1 adet

Gerekli aletler:

Demirci ocağıDemirci ocağı
Demirci kerpeteniDemirci kerpeteni
KovaKova
6

Temper purple

Brighten the edge with emery cloth and let the heat run the colour down: light purple (530 F) for chisels used on steel, dark purple (550 F) for cast and wrought iron; then cool.

Bu adım için malzemeler:

Zımpara beziZımpara bezi1 adet
SuSu1 adet

Gerekli aletler:

KovaKova
7

Grind

Grind the flat chisel edges to about 60 degrees (45-75: blunter for heavy work), keeping the edge from blueing.

Gerekli aletler:

Taşlama motoruTaşlama motoru
8

Troubleshooting

Cold chisel troubleshooting.

Flow

Loading...
9

History and honest limits

From Robert Gibson Griswold, "Tool Making for Amateurs" II, **Amateur Work** (Boston), vol. III (1903-04), pp. 304-305 and fig. 1 (checked on the archive.org scan amateurwork03bostrich); temper temperatures from his part I table. Forging heats, metric figures and tools are ours.

Malzemeler

3

Gerekli Aletler

7

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...