İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER

Hot-Water Cylinder Churn: Cream Is Crushed Between a Warm Turning Cylinder and an Adjustable Plate, Then Falls to a Dasher
Jason W. Hardie of New York received US 27,446, dated 13 March 1860, for a churn. Cream in a hopper is drawn between a turning cylinder filled with hot water and a plate set close against it, which crushes the butter globules and warms them only for that moment; it falls in a thin sheet into the churn body, losing the heat again, and a dasher driven by a band from the cylinder gathers the butter.
The patent gives no sizes and no water temperature; every size here is ours.
İleri
About 3 days, plus printing
Talimatlar
1
1
Warm for a moment only
Warm for a moment only
Jupyter defteri yükleniyor…
2
2
A turning cylinder churn, one month before
A turning cylinder churn, one month before
Ward churns inside his cylinder. Hardie works the cream on the outside of his, against a plate.
3
3
Read US 27,446
Read US 27,446
"It is desirable to have the butter globules warmed only at the moment they are acted on, and to heat the milk or cream as little, and as little time, as possible, to make good butter." ... "And the cream, after passing under the cylinder, falls in a thin sheet, or in small streams, or drops, through the air, into the churn body beneath, thereby again parting with much of the heat acquired from the cylinder."
4
4
Print the cog-wheel h
Print the cog-wheel h
Spur gear, module 2.5, 60 teeth, 18 mm wide, with a hub 30 mm across; bored 16.4 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
5
5
Print the pinion i
Print the pinion i
Spur pinion, module 2.5, 16 teeth, 18 mm wide, with a hub 30 mm across; bored 16.4 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
6
6
Print the pulleys G and H
Print the pulleys G and H
Pulley 100 mm across with a round groove for an 8 mm belt; bored 16.4 mm. Print two. PETG, 0.2 mm layers, 40 % infill, 4 walls.
7
7
Churn body C and frame I
Churn body C and frame I
From 20 mm hardwood board make the body 400 x 350 mm inside and 350 deep; glue and screw it and seal the inside joints with silicone sealant. Bore the two long walls 16.8 mm across, 120 mm above the floor and on the centre line, for the dasher's shaft p. For the frame I cut two cheeks 440 x 230 mm that stand on the body's long walls, joined by cleats so the frame lifts off. Bore both cheeks 16.8 mm for the cylinder's shaft l, 40 mm from the centre and 120 mm above the body's top edge, and 16.8 mm for the winch shaft g, 95 mm from l at 45 degrees up and outward. Screw a hardwood cross-piece f, 40 x 20 mm, between the cheeks under the plate's place, and fit a nut in it for the thumb-screw d.
Bu adım için malzemeler:
Sert Ağaç Tahtası4 adet
Ahşap Tutkalı1 adet
Ahşap vidalar40 adet
Altıgen Somun1 adetGerekli aletler:
Daire testere tezgâhı
Dekupaj Testere
Kablosuz Matkap
Matkap Ucu Takımı
Çubuklu işkence
Tornavida takımı
Şerit Metre
Zımpara Kağıdı8
8
Cylinder B, shaft l and stopper m
Cylinder B, shaft l and stopper m
Cut 300 mm of stainless tube 160 mm across. Cut two end discs from 15 mm HDPE sheet to fit inside it; bore both 16 mm on the centre for a 16 mm stainless shaft, 500 mm long, and one 20 mm, 50 mm off centre, for a rubber stopper. Press the discs into the tube on the shaft, screw them through the tube with stainless screws, and seal the discs and the shaft's passage with silicone sealant so the cylinder holds water.
Bu adım için malzemeler:
Paslanmaz çelik boru1 adet
HDPE levha1 adet
Paslanmaz çelik çubuk1 adet
Kauçuk tıpalar1 adet
Makine vidaları12 adetGerekli aletler:
Demir Testeresi
Dekupaj Testere
Kablosuz Matkap
Matkap Ucu Takımı
Eğeler (El Eğesi)
Tornavida takımı9
9
Hopper A, plate a, packing strips b and thumb-screw d
Hopper A, plate a, packing strips b and thumb-screw d
Make a hardwood hopper 302 mm long inside, to take the cylinder: an outer wall, two end walls and a bottom sloping down to the cylinder, its inner edge cut to the cylinder's curve. Bend a strip of stainless sheet to the curve and screw it over that edge as the plate a. Screw HDPE strips on the end walls' inner faces as packing b, to run against the cylinder's ends. Hang the hopper's outer bottom corner on a 10 mm stainless pin c through the cheeks. Cut 60 mm of threaded rod with a wing nut locked on one end as the thumb-screw d; run it up through the cross-piece's nut to bear under the hopper, and turn it until the plate is about 1.5 mm from the cylinder.
Bu adım için malzemeler:
Sert Ağaç Tahtası1 adet
Paslanmaz çelik levha1 adet
HDPE levha1 adet
Paslanmaz çelik çubuk1 adet
Dişli mil1 adet
Kanatlı somun1 adet
Altıgen Somun1 adet
Ahşap vidalar16 adet
Ahşap Tutkalı1 adetGerekli aletler:
Daire testere tezgâhı
Dekupaj Testere
Sac makası
Tezgah Mengenesi
Kablosuz Matkap
Matkap Ucu Takımı
Demir Testeresi
Kurbağacık anahtar
Tornavida takımı10
10
Dasher D, gears, winch E and band n
Dasher D, gears, winch E and band n
Pass a 16 mm stainless shaft p through the body's walls and fit the dasher on it: a hardwood hub with eight 12 mm dowel arms reaching 100 mm, in three sets along the shaft. Fit the cylinder's shaft in the cheeks with the pinion i on one end and the pulley G on the other, the cog-wheel h on the winch shaft g meshing the pinion, and a hardwood crank with a dowel handle on g as the winch E. Fit the pulley H on the dasher shaft's end, under G, and join them with a round belt. Hold every shaft with collars.
Bu adım için malzemeler:
Paslanmaz çelik çubuk2 adet
Sert Ağaç Tahtası1 adet
Sert ağaç kavelalar2 adet
Ahşap Tutkalı1 adet
PETG filament1 adet
Tahrik kayışı1 adet
Shaft Collar6 adet
Kopilya2 adetGerekli aletler:
FDM 3B yazıcı
Demir Testeresi
Eğeler (El Eğesi)
Kablosuz Matkap
Matkap Ucu Takımı
Tezgah Mengenesi
Kurbağacık anahtar11
11
The build in 3D
The build in 3D
FreeCAD model of this build, partly cut away: the body C with the dasher D, the frame I, the cylinder B on its shaft with the pinion i and cog-wheel h on the winch shaft, the hopper A with its plate a against the cylinder, the pivot c and thumb-screw d, and the band n from pulley G to pulley H.
12
12
Churn
Churn
Fill the cylinder with warm water from the kettle through the stopper's hole and close it; the patent gives no temperature, so check it with the thermometer and note it with the time the butter takes. Pour about 6 litres of heavy cream at about 15 °C into the hopper and turn the winch steadily, timing it; add cream to the hopper as it runs through. When the butter has gathered on the dasher, lift off the frame, take out the butter, tip the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.
Bu adım için malzemeler:
Yağlı krema6 l
Su1 adet
İri Deniz Tuzu1 adetGerekli aletler:
Elektrikli su ısıtıcısı
Takılı kalan problu termometre
Kronometre
Dijital Mutfak Terazisi
Büyük paslanmaz çelik karıştırma kâsesi13
13
Troubleshooting
Troubleshooting
Hot-water cylinder churn troubleshooting.
Flow
Loading...
14
14
History and honest limits
History and honest limits
**Jason W. Hardie** of New York, US 27,446, 13 March 1860 (signed 25 October 1859), "Churn". He disclaimed cylinders working against each other, plane rubbing surfaces, and hot water in the dasher or the main body of cream, and claimed the hollow revolving cylinder with hot water and an adjustable fixed surface against it. He gives no water temperature and no sizes; every size here is ours, our gears and pulleys are printed and sit on opposite ends of the cylinder, where his are on one end.
Malzemeler
21- 4 adetYer Tutucu
- 3 adetYer Tutucu
- 56 adetYer Tutucu
- 2 adetYer Tutucu
- 2 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 2 adetYer Tutucu
- 1 adetYer Tutucu
- 12 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 2 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 6 adetYer Tutucu
- 2 adetYer Tutucu
- 6 lYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
Gerekli Aletler
19- 1 vendor sell this, none ship to you yetYer Tutucu
- 1 vendor sell this, none ship to you yetYer Tutucu
- 1 vendor sell this, none ship to you yetYer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- 1 vendor sell this, none ship to you yetYer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
Tasarım dosyaları
4Bu planla yapılan
İlgili Blueprint'ler
Bu blueprint'ler bilgi paylaşır — teknikler, malzemeler veya ilkeler

Counter-Revolving Dasher Churn: Geared Dashers on Offset Shafts Turn Contrary Ways, Their Blades Skewed Contrary Ways
Buttercup tarafından
Ağaç işleri
6
0
0
0
0
0

Counter-Turning Cylinder Churn: The Ribbed Cylinder Turns One Way While the Dashers Inside Turn the Other
Buttercup tarafından
Ağaç işleri
8
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
TheChef tarafından
ZANAAT
63
0
0
0
0
0
CC0 Kamu Malı
Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.
Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

