İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER

Breaking Cavesson: Leather-Covered Cavesson Iron With Padded Noseband and Double Throat Lash (Hasluck, Saddlery, 1904)
A cavesson holds a young horse's head steady while it is broken in; it is used without a bit, and the leading rein goes on its rings. This is the cavesson from the breaking-down tackle in Paul N. Hasluck's Saddlery (1904): a bought cavesson iron covered in leather and padded inside, a strap up the face, cheeks, jaw straps, a headpiece and one or two throat lashes. Every size is his.
İleri
About 1 day
Talimatlar
1
1
His sizes in centimetres
His sizes in centimetres
Jupyter defteri yükleniyor…
2
2
Read Saddlery, ch. VII
Read Saddlery, ch. VII
"The cavison iron (Fig. 22) can be purchased ready-made; it acts as a noseband, being strong to hold the horse's head steady. In the centre is a ring, which turns like a swivel, and another ring is placed on each side." It has openings at the sides for the cheeks and one at each end for the straps below the jaw.
3
3
Cover the iron
Cover the iron
Cover the cavesson iron with thin brown leather and herringbone-stitch it underneath, out of sight. Make holes in the leather opposite the openings in the iron.
Bu adım için malzemeler:
Kaveson demiri1 adet
Meşin (koyun derisi)1 adet
Keten iplik1 adet
Balmumu1 adetGerekli aletler:
Deri bıçağı
Biz
İki saraç iğnesi
Saraç mengenesi4
4
Fit the cheeks
Fit the cheeks
Fit two cheeks 7 in by 1 in in the side openings, each with a runner and buckle and a loop at the top.
Bu adım için malzemeler:
Koşum derisi1 adet
Dilli demir toka2 adet
Keten iplik1 adet
Balmumu1 adetGerekli aletler:
Deri bıçağı
Kenar pahlama aleti
Deri kenar perdahlayıcı
Kıvırma aleti
Propan Pürmüz
Köprü kalıp çubuğu
Biz
İki saraç iğnesi5
5
Fit the face strap
Fit the face strap
Cut a 1 in strap 20 in long to pass round the centre of the iron, go up the face and buckle in the centre of the headpiece. Turn one end in enough to go round the iron and leave enough to stitch it together on the upper side. Slit it in half far enough to go over the centre ring, put it round with half the slit on each side of the ring, and stitch it above the iron, with a hoop under the forehead (his word) for it to pass through.
Bu adım için malzemeler:
Koşum derisi1 adet
Keten iplik1 adet
Balmumu1 adetGerekli aletler:
Deri bıçağı
Deri delme zımbası
Biz
İki saraç iğnesi
Saraç mengenesi6
6
Fit the jaw straps
Fit the jaw straps
Put a strap 9 in long in the off-side opening at the end of the iron, and another 5 in long, with a buckle, loop and runner, on the near side.
Bu adım için malzemeler:
Koşum derisi1 adet
Dilli demir toka1 adet
Keten iplik1 adet
Balmumu1 adetGerekli aletler:
Deri bıçağı
Köprü kalıp çubuğu
Deri delme zımbası
Biz
İki saraç iğnesi7
7
Make and strap on the pad
Make and strap on the pad
Make a stuffed leather pad, as for a cart winker cheek but longer, to run all along the inside of the iron and reach about 1 in beyond it at each end; it is slightly wider when stuffed and flattened. Do not make it clumsy and thick with stuffing. Make four 1/2 in straps long enough to pass round the iron, with a few holes punched in them; stitch one across the pad at each end and one on each side of the central ring, to fasten the pad on.
Bu adım için malzemeler:
Koşum derisi1 adet
Yün dolgu1 adet
Keten iplik1 adet
Balmumu1 adetGerekli aletler:
Deri bıçağı
Deri delme zımbası
Biz
İki saraç iğnesi
Saraç mengenesi8
8
Make the headpiece and throat lash
Make the headpiece and throat lash
Make the headpiece of good leather 2 ft 4 in long, so that it fits a horse of any size, and slit it 8 in or 9 in at each side so that, when cut, it is 1-3/4 in wide; it can be narrowed in the centre between the slits. Put a chape and buckle in the centre to take the face strap. Make the foreband as for a stallion bridle (the same length as an ordinary bridle front, or a little longer). Make the throat lash 1 ft 8 in long when turned in and 3/4 in wide, with a buckle, a loop and a runner at each end.
Bu adım için malzemeler:
Koşum derisi1 adet
Dilli demir toka3 adet
Keten iplik1 adet
Balmumu1 adetGerekli aletler:
Deri bıçağı
Kenar pahlama aleti
Deri kenar perdahlayıcı
Kıvırma aleti
Propan Pürmüz
Köprü kalıp çubuğu
Deri delme zımbası
Biz
İki saraç iğnesi9
9
Add a second throat lash for safety
Add a second throat lash for safety
If you want extra safety, put a 5/8 in strap 6 in long on each side of the cheek, stitched in with the chape at the top and slanting slightly downwards, and make an extra throat lash 5/8 in by 1 ft 4 in to buckle to them. "With two throat lashes the bridle will be firm and safe on the horse's head."
Bu adım için malzemeler:
Koşum derisi1 adet
Keten iplik1 adet
Balmumu1 adetGerekli aletler:
Deri bıçağı
Deri delme zımbası
Biz
İki saraç iğnesi10
10
Troubleshooting
Troubleshooting
Cavesson troubleshooting.
Flow
Loading...
11
11
History and honest limits
History and honest limits
From **Saddlery**, edited by Paul N. Hasluck, David McKay, 1904 (archive.org saddlery00hasl), chapter VII, "Breaking-down Tackle", pp. 59-61, Figs. 21-22; every fraction was read on the scan. He sends the reader to the stallion bridle for the foreband and to a cart winker cheek for the pad, without sizes here. The leading rein (9 ft by 1-1/8 in), side reins, dumb jockey, Corbett martingale, crupper and girth of the full tackle are not made here. Basil for the "thin brown leather", the buckle count in the list, the thread, tools and metric figures are ours.
Malzemeler
7- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 7 adetYer Tutucu
- 7 adetYer Tutucu
- 6 adetYer Tutucu
- 3 adetYer Tutucu
- 1 adetYer Tutucu
Gerekli Aletler
10- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
Bu planla yapılan
İlgili Blueprint'ler
Bu blueprint'ler bilgi paylaşır — teknikler, malzemeler veya ilkeler
CC0 Kamu Malı
Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.
Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.


