İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER

Horse Knee-Cap: Cupped Leather Block, Cloth Shield and Flock-Stuffed Chamois Roll (Hasluck, Saddlery, 1904)
A knee-cap protects a horse's knee from knocks and falls. This one is from Paul N. Hasluck's Saddlery (1904): a leather block beaten into a cup, set on a cloth or leather shield, a flock-stuffed chamois roll along the top strap, and a strap below the knee. Every size is his.
He notes it is often better to buy the pads, but shows how to make them.
Orta
About 1 day
Talimatlar
1
1
Cutting list
Cutting list
Jupyter defteri yükleniyor…
2
2
Read Saddlery, ch. X
Read Saddlery, ch. X
"Knee-caps are of felt, fawn rugging, kersey cloth, union, buff leather, black rubber, etc."
3
3
Beat the knee block
Beat the knee block
With no press, damp some half-curried leather and beat it, as a shoemaker beats boot soles, until it takes a hollow cup shape. Let it dry, then cut it to a wide oval about 5 in by 4 in.
Bu adım için malzemeler:
Bitkisel tabaklanmış deri1 adet
Tatlı su1 adetGerekli aletler:
Çekiç
Kucak demiri
Deri bıçağı4
4
Cut and bind the shield
Cut and bind the shield
Make the cloth, kersey or leather about 8 in at the top and 9 in deep, and round the bottom. Bind all of it except the straight top with patent binding or cloth; buff leather need not be bound.
Bu adım için malzemeler:
Yün keçe levha1 adet
Kenar biyesi şeridi1 adet
Keten iplik1 adet
Balmumu1 adetGerekli aletler:
Makas
Şerit Metre
Biz
İki saraç iğnesi5
5
Fit the block
Fit the block
Put the leather block on the centre with a piece of shaped cardboard under it, paste the two together and press the cloth down into the hollow. Stitch the block to the cloth about 1-1/4 in from the top and 1-1/2 in from the bottom.
Bu adım için malzemeler:
Yapıştırma mukavva1 adet
Buğday tutkalı1 adet
Keten iplik1 adet
Balmumu1 adetGerekli aletler:
Deri bıçağı
Biz
İki saraç iğnesi6
6
Make the top strap
Make the top strap
Cut a piece of leather 1-1/8 in wide and 1 in longer at each end than the cloth at the top. Make a hole at each end 1 in from the point for a 5/8 in strap. Put a chape, buckle and loop in the hole at one end and a 5/8 in strap 9 in long in the other, and stitch both firmly.
Bu adım için malzemeler:
Koşum derisi1 adet
Dilli pirinç toka1 adet
Keten iplik1 adet
Balmumu1 adetGerekli aletler:
Deri bıçağı
Deri delme zımbası
Biz
İki saraç iğnesi7
7
Make the padded roll
Make the padded roll
Cut chamois the same length and width as the strap. With it hanging down in front of the knee-cap and the three edges together, stitch it all along through the top leather and the cloth. Turn the chamois over the top towards the bottom and stitch it along the bottom side of the top strap, rather slack. Make two rows of stitches across the centre, leaving an opening of about 1-1/2 in exactly in the centre. Stuff both parts of the roll from each end with flock, then close the ends by stitching chamois and top leather together.
Bu adım için malzemeler:
Güderi1 adet
Yün dolgu1 adet
Keten iplik1 adet
Balmumu1 adetGerekli aletler:
Makas
Biz
İki saraç iğnesi8
8
Fit the bottom strap
Fit the bottom strap
Put a 5/8 in chape buckle and loop at the bottom of the block pad, slanting slightly downwards, with a strap 10 in long on the opposite side. For a pair, reverse the buckles so each is on the outside.
Bu adım için malzemeler:
Koşum derisi1 adet
Dilli pirinç toka1 adet
Keten iplik1 adet
Balmumu1 adetGerekli aletler:
Deri bıçağı
Biz
İki saraç iğnesi9
9
Troubleshooting
Troubleshooting
Knee-cap troubleshooting.
Flow
Loading...
10
10
History and honest limits
History and honest limits
From **Saddlery**, edited by Paul N. Hasluck, David McKay, 1904 (archive.org saddlery00hasl), chapter X, "Knee-caps and Miscellaneous Articles", pp. 81-84, Figs. 33-35; every fraction was read on the scan. He also suggests a better block cut with a tongue up under the top strap, and a fastening with two squares and a 5/8 in rubber ring; those are not shown here. The thread, the tools and the metric figures are ours.
Malzemeler
12- Yer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 5 adetYer Tutucu
- 5 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 2 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
Bu planla yapılan
İlgili Blueprint'ler
Bu blueprint'ler bilgi paylaşır — teknikler, malzemeler veya ilkeler
CC0 Kamu Malı
Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.
Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.


