İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER

Craftsman Leather Billfold: Two Cardboard Patterns, Silk Lining and Saddle-Stitched Waxed Silk (Boy Mechanic, 1919)
Livingston Haviland's billfold from The Boy Mechanic, Book 3 (1919): two leather body parts cut to stiff-cardboard patterns (13-1/4 and 8-3/16 by 4-1/4 in), lined with skiver or silk moire, folded into two card pockets and a money compartment, glued, and hand-sewn with heavy waxed silk 3/16 in from the edges.
Orta
About 1 day
Talimatlar
1
1
His patterns in centimetres
His patterns in centimetres
Jupyter defteri yükleniyor…
2
2
Read The Boy Mechanic, Book 3
Read The Boy Mechanic, Book 3
"The making of a billfold is easily within the range of an amateur in leather work, who will observe the instructions carefully." Seal, morocco, pigskin and ooze sheep are all satisfactory.
3
3
Cut the patterns and the leather
Cut the patterns and the leather
Cut two patterns of stiff cardboard (Fig. 1). Body part No. 1: 13-1/4 by 4-1/4 in, with fold lines at 2-1/2, 2-5/8, 3, 2-5/8 and 2-1/2 in, and each end (A, B) cut in with 1/2 in radius arcs, set in 1/4 in. Body part No. 2: 8-3/16 by 4-1/4 in, with fold lines at 2-19/32, 3 and 2-19/32 in. Lay each pattern on the leather and trim the leather even with it, guiding the knife with a metal straightedge, on a close-grained hardwood board or a piece of sheet zinc.
Bu adım için malzemeler:
Tabaklanmış domuz derisi1 adet
Karton şablon levhaları1 adetGerekli aletler:
Kurşun kalem
Cetvel
Düzlük mastarı
Maket Bıçağı
Sert Ağaç Tahtası
Çinko levha4
4
Line the parts
Line the parts
Cut linings slightly larger than the patterns. Skiver is glued all over with a good, pliable leather glue that will not crack the leather; smooth it on gently without stretching, or the leather may buckle, and dry it under a light weight. Silk moire is glued with a thin stripe round the edges only, left to overhang, and trimmed off neatly when dry.
Bu adım için malzemeler:
İpek Kumaş1 adet
Deri yapıştırıcısı1 adetGerekli aletler:
Makas
Maket Bıçağı5
5
Glue and fold
Glue and fold
Fold part No. 1 to form the back and the two card pockets. Apply stripes of glue as shown in Fig. 3, drop part No. 2 (the money compartment) into place, and fold the ends of No. 1 over on the dotted lines. Weight the billfold and let the glue dry.
Bu adım için malzemeler:
Deri yapıştırıcısı1 adetGerekli aletler:
Deri modelleme aleti6
6
Mark and punch the stitching
Mark and punch the stitching
Draw a straight line with a blunt-point tool along the edges to be sewn, 3/16 in from them. Mark the stitch spacing for an inch on a strip of paper and transfer it along the line. Punch the holes on a pine board with a diamond-pointed awl held vertical (D); back the open ends with strips of cardboard while punching.
Gerekli aletler:
Deri modelleme aleti
Cetvel
Taban dikiş bizi
Çam tahta
Karton şablon levhaları7
7
Sew and finish the edges
Sew and finish the edges
Sew with heavy waxed silk matching the leather, by hand or with the work clamped between two boards. Thread a needle on each end, start both from the right side (E), pass the needle from the first hole through the second (F) and, with the needles in position (G), continue this stitch. Tie the ends neatly. Trim the edges and tool them smooth with a suitable metal tool or rod, heated moderately, applying water with the fingertip.
Bu adım için malzemeler:
İpek iplik1 adet
Balmumu1 adetGerekli aletler:
İki saraç iğnesi
Makas
Maket Bıçağı
Yumuşak çelik yuvarlak çubuk8
8
Troubleshooting
Troubleshooting
Billfold troubleshooting.
Flow
Loading...
9
9
History and honest limits
History and honest limits
From "A Craftsman Leather Billfold" by Livingston Haviland, in **The Boy Mechanic, Book 3**, Popular Mechanics, 1919 (Project Gutenberg 71856; checked on the archive.org scan boymechanic0003unse, pp. 446-447). He does not give the number of stitches to the inch or what waxes the silk (beeswax is ours). Pigskin is one of his four leathers. The tools and metric figures are ours.
Malzemeler
6- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 2 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
Gerekli Aletler
13- 1 vendor sell this, none ship to you yetYer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
Bu planla yapılan
İlgili Blueprint'ler
Bu blueprint'ler bilgi paylaşır — teknikler, malzemeler veya ilkeler
CC0 Kamu Malı
Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.
Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.


