İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Iron Ball Mill: Grüson Drum with a Stepped Die Ring and Two Screens (Richards, 1903)
Forge

Oluşturan

Forge

3. Kasım 2026NO
8
0
0
0
0

Iron Ball Mill: Grüson Drum with a Stepped Die Ring and Two Screens (Richards, 1903)

The Grüson ball mill: a drum turning on a horizontal axis, charged with chilled iron or steel balls of mixed sizes. The balls grind the ore against each other and against a stepped die ring. The ground ore passes out through a coarse and a fine screen; the oversize is carried back in. Result: a mill for fine grinding of cement, fertiliser, clay and soft ores, wet or dry. Sizes from 0.66 m to 1.83 m across. Source: R. H. Richards, Ore Dressing, vol. I (1903), § 225, Figs. 172a-b and Table 149. Unknown: dimensions beyond the table, and the materials of the side plates, screens and shaft. Picture: Richards, Figs. 172a-b.
İleri
Unknown

Talimatlar

1

Make the drum and the die ring

The drum is two side plates (b) joined round the edge by the die ring (a). The die ring is five perforated, spiral plates of chilled iron. Each plate laps the next, so they form steps: the balls drop from one step to the next, and the space under each step lets the oversize from the screens back in. Not given: the side-plate material, sizes, hole sizes.

Bu adım için malzemeler:

Dökme demir parçalarDökme demir parçalar5 die plates, chilled iron
Bilinmeyen malzemeBilinmeyen malzeme2 side plates

Gerekli aletler:

Bilinmeyen ölçülerBilinmeyen ölçüler
Kurbağacık anahtarKurbağacık anahtar
2

Put the two screens round it

Outside the die ring, fit a coarse perforated screen (c) to take the wear. It is in five parts with spaces between them and has back-deflecting holes (g). Outside that, fit a fine gauze screen (d). At the end of each section of fine screen, fix a deflector or shovel (f). As the drum turns, it carries the oversize up and back into the grinding space. Not given: the screens' metal and mesh.

Bu adım için malzemeler:

Delikli elek sacıDelikli elek sacı1 coarse screen, 5 parts
Dokuma tel elek beziDokuma tel elek bezi1 fine screen
Bilinmeyen malzemeBilinmeyen malzeme5 deflectors

Gerekli aletler:

Bilinmeyen ölçülerBilinmeyen ölçüler
Kurbağacık anahtarKurbağacık anahtar
3

Mount and house it

Carry the drum on a horizontal shaft in two bearings; the figures show them on masonry piers. Enclose the drum in a plate iron housing with a discharge spout (e) below, a feed hopper (h) at one end, a manhole (i) and a dust pipe (k) on top. Ours: steel sheet for the plate iron.

Bu adım için malzemeler:

Çelik milÇelik mil1 mill shaft
Rulman yatağıRulman yatağı2 adet
Yumuşak Çelik SacYumuşak Çelik Sac1 housing, spout, hopper

Gerekli aletler:

Kurbağacık anahtarKurbağacık anahtar
Bilinmeyen ölçülerBilinmeyen ölçüler
4

Fit the drive

Drive the mill by gear and pinion. In the figure, the gear is on the mill shaft and the pinion on a countershaft that carries tight and loose pulleys. A belt from the line shaft runs on the pulleys: on the tight pulley the mill turns, on the loose pulley it stops.

Bu adım için malzemeler:

Tahrik edilen dişli çarkTahrik edilen dişli çark1 on the mill shaft
Pinyon dişlisiPinyon dişlisi1 adet
Çelik milÇelik mil1 countershaft
Rulman yatağıRulman yatağı2 adet
Sabit ve boş kasnakSabit ve boş kasnak1 adet

Gerekli aletler:

Tahrik kayışıTahrik kayışı
Kurbağacık anahtarKurbağacık anahtar
5

Charge the balls (size sets the charge)

Load chilled iron or steel balls in mixed sizes; mixed sizes grind better than one size. Size is the variable: No. 0 (0.660 m drum, 45 rev/min) takes 15 kg of 40 mm and 45 kg of 80 mm balls, 60 kg in all. No. 2 (1.330 m, 30 rev/min) takes 100 kg each of 100, 115 and 125 mm, 300 kg. No. 4 (1.830 m, 25 rev/min) takes 217 kg each of the same three sizes, 650 kg. The bigger the drum, the slower it turns and the heavier its charge.

Bu adım için malzemeler:

Öğütücü ortam (çelik bilyalar)Öğütücü ortam (çelik bilyalar)300 kg for No. 2; 60 kg No. 0, 650 kg No. 4

Gerekli aletler:

Endüstriyel platform kantarıEndüstriyel platform kantarı
6

Grind

Feed the ore, egg-size, through the hopper and run the mill wet or dry. Power, and output per 24 hours: No. 0 takes 1/4 horse power and grinds 1,680 kg of copper ore to 15 mesh, or 840 kg of chrome iron ore to 130 mesh. No. 2 takes 2 1/2 to 3 horse power: 14,400 kg of brick bats to 20 mesh, or 1,920 kg of emery to 200 mesh. No. 4 takes 9 to 11 horse power: 12,720 kg of gold ores to 40 mesh, or 10,800 kg of chrome iron ore to 130 mesh. Wear: 1,345 kg of balls for 102,400 barrels of cement, about 0.139 lb a ton. The end plates last 18 months. Hard quartz ores wear the balls too much.

Gerekli aletler:

Tahrik kayışıTahrik kayışı
SuSu

Malzemeler

11

Gerekli Aletler

5

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...