İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER

Segmental-Stave Churn: Thick Curved Staves Split the Cream's Current, a Long Blade Sweeps Beneath Them
Thomas A. Jebb of Buffalo, New York, received US 26,109, dated 15 November 1859, for a churn. Three of the tub's staves are made much thicker on one edge, curving inward, so the turning cream rides up their faces, rebounds and eddies in their lee. A dash of five wedge-shaped blades at right angles turns on an upright shaft; the lowest blade is long and sweeps under the staves' bevelled ends so nothing lodges on the bottom. The gearing sits on a hinged cross piece clear of the cream.
The patent gives no sizes; every size here is ours.
Orta
About 2 days, plus printing
Talimatlar
1
1
Long blade under, short blades within
Long blade under, short blades within
Jupyter defteri yükleniyor…
2
2
Breaking the turning cream on the tub's wall, two months before
Breaking the turning cream on the tub's wall, two months before
Taylor fixed thin brakes and ledges to the wall. Jebb makes three staves themselves thick and curved, and runs a long blade under them.
3
3
Read US 26,109
Read US 26,109
"The dash blades are caused to revolve by turning the crank S, the bevel face (k-l) of the blade striking against the cream causing a portion of it to pass up the incline face (k-l) and fall down on the line (l-m) while a portion is thrown from B, to B, with a rebound, and a portion forms an “eddy” and backward current in the “lee” of the thick edge of, B."
4
4
Print the wheel Q
Print the wheel Q
Crown wheel, 36 teeth on its face, module 2, with a hub bored 12.4 mm and a cross hole for a pin. PETG, 0.2 mm layers, 40 % infill, 4 walls.
5
5
Print the pinion P
Print the pinion P
Spur pinion, 12 teeth, module 2, with a hub bored 12.4 mm and a cross hole for a pin. PETG, 0.2 mm layers, 40 % infill, 4 walls.
6
6
Print the bearing n
Print the bearing n
A cup 50 mm across and 15 mm tall with a 20 mm socket for the shaft's foot. PETG, 0.2 mm layers, 40 % infill, 4 walls.
7
7
Tub A and staves B
Tub A and staves B
Use a wooden tub 270 mm across inside at the floor, 300 mm at the top and 380 mm deep. From hardwood cut three segments to lie against the wall over 60 degrees each, thin at one edge and rising on a quarter circle to 44 mm thick at the other, 330 mm tall. Bevel each one's foot upward towards the middle, from 50 mm up at the wall to 95 mm at its thick edge. Glue and screw them inside, a third of the way round from each other, all thick edges facing the same way round. Glue the bearing cup in the middle of the floor. Fill the tub with water overnight so it swells tight, then empty it.
Bu adım için malzemeler:
Ahşap tekne1 adet
Sert Ağaç Tahtası2 adet
Ahşap Tutkalı1 adet
Ahşap vidalar18 adet
PETG filament1 adetGerekli aletler:
FDM 3B yazıcı
Dekupaj Testere
Çift saplı rende
Daire testere tezgâhı
Kablosuz Matkap
Matkap Ucu Takımı
Çubuklu işkence
Şerit Metre
Su8
8
Dash: shaft I and blades H, H2
Dash: shaft I and blades H, H2
Turn a hardwood shaft 30 mm across and 400 mm long, its foot turned to 19 mm for 11 mm, and fit a 12 mm stainless pin 52 mm long in its top for the pinion. Cut five blades 40 x 15 mm and shave each to a wedge, its two faces bevelled opposite ways. Make the lowest 256 mm long and the other four 164 mm. Mortise them through the shaft at positions 25, 100, 160, 220 and 280 mm above the tub's floor, each at right angles to the one below.
Bu adım için malzemeler:
Sert Ağaç Tahtası1 adet
Sert ağaç kavelalar1 adet
Ahşap Tutkalı1 adet
Paslanmaz çelik çubuk1 adetGerekli aletler:
Ahşap torna tezgâhı
Zıvana yuvası kalemi
Ahşap Tokmak
Çift saplı rende
Demir Testeresi
Zımpara Kağıdı
Şerit Metre9
9
Cover, cross piece M and gearing
Cover, cross piece M and gearing
Cut a round cover in two halves to rest on the staves' tops, with a 32 mm hole for the shaft. Hinge a hardwood cross piece M, 60 x 20 mm, across the tub's top with a strap hinge on one side (g2), resting on a cleat on the other (g3), bored 14 mm for the shaft's pin. On it screw two chairs carrying a 12 mm stainless shaft R with the crown wheel and a crank S, and pin the pinion on the shaft's top so the two mesh. Lift M on its hinge to free the shaft.
Bu adım için malzemeler:
Sert Ağaç Tahtası2 adet
Demir şerit menteşe1 adet
Ahşap vidalar12 adet
Paslanmaz çelik çubuk1 adet
Sert ağaç kavelalar1 adet
Ahşap Tutkalı1 adetGerekli aletler:
Dekupaj Testere
Pusula
Kablosuz Matkap
Matkap Ucu Takımı
Demir Testeresi
Eğeler (El Eğesi)
Tornavida takımı10
10
The build in 3D
The build in 3D
FreeCAD model of this build, the tub and cover cut through the middle: the three curved staves with their bevelled feet, the dash with its long lower blade and four short ones, the bearing, and the cross piece with the crown wheel, pinion and crank. The dash was turned through 36 positions.
11
11
Churn
Churn
Pour in heavy cream at about 15 °C, checked with the thermometer, from a few litres up to about 12, put the cover halves and the cross piece down, and turn the crank steadily, timing it. When the butter comes it rises to the top: lift M and the cover, take the butter out, drain the buttermilk, wash the butter in cold water until it runs clear, salt and weigh it.
Bu adım için malzemeler:
Yağlı krema12 l
İri Deniz Tuzu1 adet
Su1 adetGerekli aletler:
Takılı kalan problu termometre
Kronometre
Dijital Mutfak Terazisi
Büyük paslanmaz çelik karıştırma kâsesi12
12
Troubleshooting
Troubleshooting
Segmental-stave churn troubleshooting.
Flow
Loading...
13
13
History and honest limits
History and honest limits
**Thomas A. Jebb** of Buffalo, New York, US 26,109, 15 November 1859, "Churn". He claimed the short dash blades H and the long blade H2 arranged with the segmental stave B, the short blades turning within and the long one under its bevelled end, and the blades' arrangement with the staves. His thick staves are single solid staves of the tub "leaving no interstice in the stave for the milk to lodge in and get sour"; ours are segments fixed inside a bought tub. His bevel pinion and wheel are here a printed pinion and crown wheel. The patent gives no sizes; every size here is ours.
Malzemeler
11- 1 adetYer Tutucu
- 2 adetYer Tutucu
- 3 adetYer Tutucu
- 30 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 12 lYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
Gerekli Aletler
21- Yer Tutucu
- 1 vendor sell this, none ship to you yetYer Tutucu
- Yer Tutucu
- 1 vendor sell this, none ship to you yetYer Tutucu
- 1 vendor sell this, none ship to you yetYer Tutucu
- Yer Tutucu
- Yer Tutucu
- 1 vendor sell this, none ship to you yetYer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
Tasarım dosyaları
4Bu planla yapılan
İlgili Blueprint'ler
Bu blueprint'ler bilgi paylaşır — teknikler, malzemeler veya ilkeler

Brake-and-Ledge Bar Dasher Churn: Slotted Brakes Break the Current, Ledges Turn It Back to the Dasher
Buttercup tarafından
Ağaç işleri
11
0
0
0
0
0

Hinged-Leaf Wing Dasher Churn: Turn One Way to Churn, Reverse and a Leaf Opens to Gather the Butter
Buttercup tarafından
Ağaç işleri
7
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
TheChef tarafından
ZANAAT
63
0
0
0
0
0
CC0 Kamu Malı
Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.
Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

