İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER

Kitchen Funnel with Air-Vent Ribs, 3D Printed in PETG
A 120 mm kitchen funnel for bottling wine, cider or juice, printed in one piece in PETG. Three small ribs along the outside of the spout hold it off the bottle neck so air can come out while the liquid goes in, so it pours without glugging. A common, open design; all sizes are ours, and we have not printed or tested it yet.
Başlangıç
About 4 hours, mostly printing
Talimatlar
1
1
Our funnel's numbers
Our funnel's numbers
Jupyter defteri yükleniyor…
2
2
Make it fit your bottles
Make it fit your bottles
Optional: change TOP_D or the spout sizes and run it in FreeCAD: OUT=. TOP_D= freecadcmd build_all.py
build_all.pypython
Gerekli aletler:
Dijital Kumpas 6 İnç3
3
Print the funnel
Print the funnel
Print it rim down on the bed, no supports; the cone and spout grow upward. PETG sold for food contact, a stainless steel nozzle (brass nozzles can contain lead), 0.2 mm layers, at least 3 walls.
Bu adım için malzemeler:
PETG filament60 gGerekli aletler:
FDM 3B yazıcı
3B yazıcı nozul seti4
4
Clean it up
Clean it up
Trim any strings or blobs, especially inside the spout and between the ribs. Check the spout is clear.
Gerekli aletler:
Maket Bıçağı5
5
Check the fit
Check the fit
Put the spout into a bottle: the ribs should touch the neck and leave gaps between them. Pour water through and watch it run without glugging.

Gerekli aletler:
Tıpalı cam şişeler
Su6
6
Sanitise
Sanitise
Soak it in no-rinse sanitiser mixed as its label says. Do not boil it: PETG softens at about 80 °C.
Gerekli aletler:
Dezenfektan
Su7
7
Troubleshooting
Troubleshooting
Funnel problems and fixes.
Flow
Loading...
8
8
Honest limits
Honest limits
A common, open design, drawn by us in FreeCAD; every size is ours. The ribs were checked by slicing the model; the funnel has not been printed or poured through by us yet. Sanitise before every use and replace it when scratched.
Malzemeler
1- 60 gYer Tutucu
Gerekli Aletler
7- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
Tasarım dosyaları
1Bu planla yapılan
İlgili Blueprint'ler
Bu blueprint'ler bilgi paylaşır — teknikler, malzemeler veya ilkeler
CC0 Kamu Malı
Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.
Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.




