İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Oscillating-Pump Churn: A Half-Round Vane Pump Lifts the Cream Over and Strains It Back Through a Partition
Martin

Oluşturan

Martin

9. Kasım 2026NO
10
0
0
0
0

Oscillating-Pump Churn: A Half-Round Vane Pump Lifts the Cream Over and Strains It Back Through a Partition

W. H. McClintock of Frankfort, Ohio, received US 24,223, dated 31 May 1859, for a churn that is a pump. A box is divided by a perforated partition into a cream chamber and a butter chamber. In the cream chamber a half-round pump has a vane swung back and forth by a lever: each stroke sucks cream up through a passage round the pump and flap valves into one side, and forces the other side's cream up through valves on top into a channel that runs into the butter chamber. The cream strains back through the partition and goes round again, chafed at every pass, until the butter is left in the butter chamber. Pumping water round the same way rinses the churn and washes the butter. This rung builds it in a pine box with a printed pump.
İleri
About 1 day, plus printing

Talimatlar

1

What one stroke moves

Jupyter defteri yükleniyor…
2

Cream thrown over a partition, before it

Patterson's fan threw cream over a partition to return under it. McClintock pumps it over and strains it back.
3

Read US 24,223

"The cream first expelled flows into the chamber C, and by reason of the continued suction of the piston is caused to strain through the perforated partition D, and enter the cream or milk chamber again ready to be again similarly circulated, minus a greater portion of its fatty matter, said fatty matter remaining in the chamber C."
4

Print the pump E

The pump body: half-round chamber a, passage b round it with its inlet below, ports for valves c c'. Print it upside down on its flat top. PETG, 0.2 mm layers, 40 % infill, 4 walls; wash before first use.
Tasarım DosyasıSTLCC0 - Free
5

Print the vane f

The piston vane with its half-round hub. PETG, 0.2 mm layers, 40 % infill, 4 walls; wash before first use.
Tasarım DosyasıSTLCC0 - Free
6

Box A and partition D

From 18 mm pine make a box 500 x 220 mm and 300 mm deep inside, with a lid and knob. Screw pairs of 10 mm strips down both side walls 300 mm from the left end as grooves, and slide in a 12 mm plywood partition D 212 mm high, drilled all over with 8 mm holes 20 mm apart, with a knob to lift it. Fit a PVC spigot low in the right end, in chamber C, as the opening j.

Bu adım için malzemeler:

Çam tahtaÇam tahta3 adet
Ahşap TutkalıAhşap Tutkalı1 adet
Ahşap vidalarAhşap vidalar40 adet
Sert Ağaç TahtasıSert Ağaç Tahtası1 adet
Kontrplak levhaKontrplak levha1 adet
Sert ağaç kavelalarSert ağaç kavelalar1 adet
PVC muslukPVC musluk1 adet
Silikon Dolgu MacunuSilikon Dolgu Macunu1 adet

Gerekli aletler:

El TesteresiEl Testeresi
Dekupaj TestereDekupaj Testere
Kablosuz MatkapKablosuz Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Panç testere setiPanç testere seti
İşkencelerİşkenceler
Zımpara KağıdıZımpara Kağıdı
Tornavida takımıTornavida takımı
Şerit MetreŞerit Metre
7

Pump E and top plate

Cut a 12 mm plywood top plate 290 x 220 mm to fill chamber B from the left end to the partition. Cut a half-round groove across its underside for the vane's hub, 37 mm wide, centred 150 mm from the left end, and drill two 20 mm eduction holes d d' 50 mm each side of it. Glue rubber-sheet flaps e e' 32 mm square over them on top, hinged on one edge with a screw. Glue rubber flaps c c' over the two ports inside the pump's chamber, hinged at the top so they open inward. Screw the pump body under the plate, seal the joint with silicone, and rest the plate on cleats 200 mm above the floor so it closes chamber B.

Bu adım için malzemeler:

PETG filamentPETG filament1 adet
Kontrplak levhaKontrplak levha1 adet
Kauçuk levhaKauçuk levha1 adet
Silikon Dolgu MacunuSilikon Dolgu Macunu1 adet
Ahşap vidalarAhşap vidalar12 adet
Çam tahtaÇam tahta1 adet

Gerekli aletler:

FDM 3B yazıcıFDM 3B yazıcı
Dekupaj TestereDekupaj Testere
Panç testere setiPanç testere seti
Maket bıçağıMaket bıçağı
Kablosuz MatkapKablosuz Matkap
Tornavida takımıTornavida takımı
8

Vane f, lever g and channel F

Fix the vane on a 12 mm stainless rod with an M4 screw across, set it in the chamber with the hub in the plate's groove, and pass the rod out through the pump's end and the box's near wall. Fix a hardwood lever g 24 x 12 mm, 245 mm long, on the rod outside, standing up past the lid, with a 28 mm dowel handle on top. Fix a pine board above the top plate, sloping down from 258 mm high at the left end to 238 mm over the partition, to form channel F into C.

Bu adım için malzemeler:

Paslanmaz çelik çubukPaslanmaz çelik çubuk1 adet
Makine vidalarıMakine vidaları1 adet
Naylon Fiberli Emniyet SomunuNaylon Fiberli Emniyet Somunu1 adet
Sert Ağaç TahtasıSert Ağaç Tahtası1 adet
Sert ağaç kavelalarSert ağaç kavelalar1 adet
Ahşap TutkalıAhşap Tutkalı1 adet
Çam tahtaÇam tahta1 adet
Ahşap vidalarAhşap vidalar8 adet

Gerekli aletler:

Demir TesteresiDemir Testeresi
El TesteresiEl Testeresi
Kablosuz MatkapKablosuz Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Tornavida takımıTornavida takımı
9

The build in 3D

FreeCAD model of this build, the near half cut away: box A with partition D in its grooves, the pump body with passage b and its inlet, the vane, the top plate with flaps e e', flaps c c' at the ports, channel F's board and the spigot. It was checked at five vane angles from -60 to +60 degrees.
Tasarım DosyasıBLENDCC0 - Free
10

Churn

Pour about 8 litres of heavy cream at about 15 °C into chamber B through C (it strains through the partition), checked with the thermometer, and put the lid on. Swing the lever steadily back and forth about 60 degrees each way and time it: cream spurts into channel F, runs into C and strains back. When the butter has gathered in C, draw off the buttermilk at the spigot, pour cold water in and pump it round to rinse the churn and wash the butter, then lift the butter out, work in a pinch of salt and weigh it.

Bu adım için malzemeler:

Yağlı kremaYağlı krema8 l
SuSu1 adet
İri Deniz Tuzuİri Deniz Tuzu1 adet

Gerekli aletler:

Takılı kalan problu termometreTakılı kalan problu termometre
KronometreKronometre
Dijital Mutfak TerazisiDijital Mutfak Terazisi
Büyük paslanmaz çelik karıştırma kâsesiBüyük paslanmaz çelik karıştırma kâsesi
11

Troubleshooting

Pump churn troubleshooting.

Flow

Loading...
12

History and honest limits

**W. H. McClintock** of Frankfort, Ross County, Ohio, US 24,223, 31 May 1859, "Churn". He claimed the circularly vibrating suction and force pump with a churn having a perforated partition. He gave no sizes or materials: the box, the printed pump, the rubber flaps and every size are ours.

Malzemeler

16

Gerekli Aletler

16

Tasarım dosyaları

3

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...