İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Surface Dash-Wheel Churn: A Fast Fan Skims the Cream Over a Partition on a Parallel-Rule Frame
Buttercup

Oluşturan

Buttercup

9. Kasım 2026IE
11
0
0
0
0

Surface Dash-Wheel Churn: A Fast Fan Skims the Cream Over a Partition on a Parallel-Rule Frame

Andrew Patterson of Birmingham, Pennsylvania, received US 23,111, dated 1 March 1859, for a churn whose fan wheel only strikes the surface of the cream. Turned fast through a pulley, it throws the cream over a partition; the cream sinks and comes back under it. The wheel's chamber is also the churn's lid and rests on a jointed frame that works like a parallel rule, so a handle sets the fan to dip about 1/8 in. into whatever quantity of cream is in the box. This rung builds it in pine with a belt-driven printed fan.
Orta
About 8 hours, plus printing

Talimatlar

1

Setting the rest for the cream you have

Jupyter defteri yükleniyor…
2

A dasher that adjusts to the tub, before it

Fiester's blades spread to fit his tub. Patterson moves his whole fan up and down to the cream's surface.
3

Read US 23,111

"... the rest o, o, w, v, v, is raised or lowered until when b is placed on it the buckets or fans will dip about one-eighth of an inch into the cream and the crank is turned rapidly in such manner that the wheel shall impel the milk or cream which it strikes in the direction of w".
4

Print the hub

The fan's hub with eight square sockets for the arms. PETG, 0.2 mm layers, 40 % infill, 4 walls; wash before first use.
Tasarım DosyasıSTLCC0 - Free
5

Print the bucket y

A curved bucket for an arm pair's ends. Print four. PETG, 0.2 mm layers, 40 % infill, 4 walls; wash before first use.
Tasarım DosyasıSTLCC0 - Free
6

Box a

From 18 mm pine make an oblong box open at the top, 600 x 300 mm and 320 mm deep inside: floor 636 x 336 mm, sides 636 x 320 mm, ends 300 x 320 mm, glued and screwed.

Bu adım için malzemeler:

Çam tahtaÇam tahta2 adet
Ahşap TutkalıAhşap Tutkalı1 adet
Ahşap vidalarAhşap vidalar30 adet

Gerekli aletler:

El TesteresiEl Testeresi
Kablosuz MatkapKablosuz Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
İşkencelerİşkenceler
Zımpara KağıdıZımpara Kağıdı
Tornavida takımıTornavida takımı
Şerit MetreŞerit Metre
7

The parallel rest v v o o w

Cut two hardwood uprights o 30 x 13 x 190 mm and pin each to a side of the box with an 8 mm bolt 22 mm above the inside floor, 100 mm from the right end. Cut a pine division board w 228 x 170 mm and pin its foot to two hardwood blocks on the floor 200 mm from the left end, so it stands 16 mm clear of the floor. Cut two hardwood bars v 20 x 20 x 340 mm and pin them to the uprights' tops and w's top corners, 300 mm apart, with 160 mm between each foot and top pivot, so the bars stay level as the frame leans. Screw a hardwood handle h i 30 x 12 mm to the left end of one bar, long enough to stand 100 mm above the rim, and bend a flat-bar frame e over the rim to hold it with a pin through holes drilled every 20 mm in the handle.

Bu adım için malzemeler:

Sert Ağaç TahtasıSert Ağaç Tahtası1 adet
Çam tahtaÇam tahta1 adet
Makine vidalarıMakine vidaları8 adet
Naylon Fiberli Emniyet SomunuNaylon Fiberli Emniyet Somunu8 adet
Düz PulDüz Pul16 adet
Yumuşak Çelik LamaYumuşak Çelik Lama1 adet
Ahşap vidalarAhşap vidalar6 adet

Gerekli aletler:

El TesteresiEl Testeresi
Kablosuz MatkapKablosuz Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Demir TesteresiDemir Testeresi
Tezgah MengenesiTezgah Mengenesi
Eğeler (El Eğesi)Eğeler (El Eğesi)
Kurbağacık anahtarKurbağacık anahtar
8

Chamber b and the fan

From pine make chamber b open below: two sides 360 x 270 mm, two ends 234 x 270 mm and a top 360 x 270 mm, 270 mm wide outside so it sits on the bars inside a. Drill both sides 12.5 mm for the fan shaft 40 mm up from b's lower edge and 230 mm from its left end, and one side again 170 mm above that for the crank shaft. Cut the 12 mm stainless rod to 285 mm for the fan. Push eight hardwood arms 18 x 18 x 69 mm into the hub's sockets, screw a bucket across each pair of arm ends, slide the hub onto the shaft inside b and fix it with an M4 screw across.

Bu adım için malzemeler:

Çam tahtaÇam tahta2 adet
Ahşap TutkalıAhşap Tutkalı1 adet
Ahşap vidalarAhşap vidalar20 adet
Paslanmaz çelik çubukPaslanmaz çelik çubuk1 adet
Sert Ağaç TahtasıSert Ağaç Tahtası1 adet
PETG filamentPETG filament1 adet
Makine vidalarıMakine vidaları9 adet
Naylon Fiberli Emniyet SomunuNaylon Fiberli Emniyet Somunu9 adet

Gerekli aletler:

FDM 3B yazıcıFDM 3B yazıcı
El TesteresiEl Testeresi
Kablosuz MatkapKablosuz Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Demir TesteresiDemir Testeresi
Eğeler (El Eğesi)Eğeler (El Eğesi)
Tornavida takımıTornavida takımı
9

Pulleys f and c, crank t

Cut a pulley f 240 mm across and a pulley c 60 mm across from 12 mm plywood, each with a 3 mm flange glued on the outer face, and file a groove round each rim for the cord. Fix c on the fan shaft outside b. Run a 12 mm stainless stub shaft through b's side 170 mm above, fix f on it and a hardwood crank arm 24 x 10 x 112 mm with a 24 mm dowel handle 80 mm long beyond it, out over the side of a. Tie a loop of 6 mm cotton cord round both pulleys.

Bu adım için malzemeler:

Kontrplak levhaKontrplak levha1 adet
Ahşap TutkalıAhşap Tutkalı1 adet
Paslanmaz çelik çubukPaslanmaz çelik çubuk1 adet
Sert Ağaç TahtasıSert Ağaç Tahtası1 adet
Sert ağaç kavelalarSert ağaç kavelalar1 adet
Pamuk halatPamuk halat1 m
Makine vidalarıMakine vidaları2 adet
Naylon Fiberli Emniyet SomunuNaylon Fiberli Emniyet Somunu2 adet

Gerekli aletler:

Dekupaj TestereDekupaj Testere
Eğeler (El Eğesi)Eğeler (El Eğesi)
Kablosuz MatkapKablosuz Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Demir TesteresiDemir Testeresi
Tornavida takımıTornavida takımı
10

The build in 3D

FreeCAD model of this build, the near side of both boxes cut away: box a, the uprights, division board and bars of the parallel rest leaning 50 degrees, chamber b on the bars, the fan with its buckets, pulleys f and c, the crank, and handle h i in its frame e. The cord is not drawn.
Tasarım DosyasıBLENDCC0 - Free
11

Churn

Pour in about 14 litres of heavy cream at about 15 °C, checked with the thermometer. Set chamber b on the bars and move the handle until the buckets just dip into the cream, about 3 mm, then pin it in frame e (the notebook gives the lean for other quantities). Turn the crank fast and time it: the fan throws cream over the division board and it returns under it. When the butter comes, lift b off, pour off the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.

Bu adım için malzemeler:

Yağlı kremaYağlı krema14 l
İri Deniz Tuzuİri Deniz Tuzu1 adet
SuSu1 adet

Gerekli aletler:

Takılı kalan problu termometreTakılı kalan problu termometre
KronometreKronometre
Dijital Mutfak TerazisiDijital Mutfak Terazisi
Büyük paslanmaz çelik karıştırma kâsesiBüyük paslanmaz çelik karıştırma kâsesi
12

Troubleshooting

Surface dash-wheel churn troubleshooting.

Flow

Loading...
13

History and honest limits

**Andrew Patterson** of Birmingham, Allegheny County, Pennsylvania, US 23,111, 1 March 1859, "Churn". He held that a fast fan at the surface does more than a submerged wheel, which has to lift the whole cream, and that it also gathers the butter on the far side of the partition. He claimed box a with chamber b serving as its lid and as the frame for the dash wheel and crank. His only figure is the 1/8 in. dip; every size and material here is ours.

Malzemeler

16

Gerekli Aletler

17

Tasarım dosyaları

3

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...