SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
YEŞİL GELECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Making a Wooden Bucket — Basic Cooperage with Staves and Hoops
Woody

Oluşturan

Woody

26. Mayıs 2026NO
16
0
0
0
0

Making a Wooden Bucket — Basic Cooperage with Staves and Hoops

A wooden bucket is one of the earliest watertight vessels made entirely from wood and metal — a set of shaped staves held together by hoops that compress the joints into a seal. The cooper's trade (barrel and bucket making) was one of the most important crafts from antiquity through the Industrial Revolution. Every liquid — water, wine, beer, oil, vinegar — was stored and transported in cooperage.

A bucket is the simplest form of cooperage: straight staves arranged in a circle, wider at the top than the bottom, bound by two or three iron hoops. The staves taper in width so that when assembled they form a truncated cone. Each stave edge is bevelled at a precise angle — when the hoops are driven down, the bevel faces press together and the vessel becomes watertight without any sealant.

The skill is in the stave preparation. Each stave must be riven from straight-grained oak or similar hardwood, shaped with a drawknife, and bevelled with a jointer plane or drawknife to the exact angle. If even one stave is wrong, the bucket leaks. A good cooper could produce a watertight bucket in two to three hours from prepared staves.

İleri
6-8 hours

Talimatlar

1

Rive and prepare the staves

Rive 10-14 staves from a straight-grained oak bolt using a froe. Each stave should be about 30-40 cm long (the height of the bucket), 5-7 cm wide, and 1.5-2 cm thick. The grain must run the full length without runout — a stave with cross-grain splits when the hoops compress it. Rough each stave to a slight taper: wider at the top (the mouth of the bucket) and narrower at the bottom. The taper creates the outward slope of the bucket wall.

Gerekli aletler:

FroeFroe
2

Shape and bevel the stave edges

Clamp each stave in a shave horse and use a drawknife to smooth the outer face (slightly convex) and inner face (slightly concave). The critical step is bevelling the edges. Each stave edge must be cut at an angle so that when all staves are arranged in a circle, the bevelled faces press tight against each other. For a 12-stave bucket, each edge is bevelled at about 15 degrees (360 divided by 24 edges = 15 degrees). Use a drawknife or a jointer plane to cut this bevel consistently along the full length of each edge.

Gerekli aletler:

DrawknifeDrawknife
3

Cut the croze groove for the bottom

The bottom board sits in a groove cut around the inside of the staves, about 2-3 cm up from the base. This groove is called the croze. Cut it with a narrow chisel or a purpose-made croze tool — a groove about 5 mm wide and 5 mm deep, at a consistent height on every stave. The bottom board will slide into this groove during assembly. The groove must be cut before the staves are assembled, while each stave is still accessible individually.
4

Assemble the staves and drive the hoops

Arrange the staves in a circle with the tapered ends (bottom) together. Place a temporary cord or a loose iron hoop around the top to hold them upright. Start with the top hoop — slide it down over the staves and tap it with a hammer, working evenly around the circumference. As the hoop descends, it compresses the staves together and the bevelled edges press into tight joints. Drive a second hoop near the bottom. The staves should now hold together by friction alone. Adjust any stave that sits proud by tapping it inward with a mallet.

Bu adım için malzemeler:

Iron HoopIron Hoop2 adet

Gerekli aletler:

Forge Hammer (Cross-Peen)Forge Hammer (Cross-Peen)
5

Fit the bottom board

Remove the bottom hoop temporarily. Cut a circular board from a piece of riven oak — slightly larger than the inside diameter of the bucket at the croze level. Bevel the edge of the board so it slides into the croze groove. Push the staves apart slightly at the bottom, slide the board into the groove, and re-drive the bottom hoop. The hoop compresses the staves against the board, and the board is held firmly in the groove. If the fit is tight and the staves well-jointed, the bucket is watertight immediately.
6

Attach a handle and test for leaks

Select two opposite staves and leave them slightly longer than the others (or drill holes through them near the top). Thread a bent iron rod or a stiff wooden withe through the holes as a bail handle. Fill the bucket with water and let it stand for several hours. A new oak bucket often weeps at the joints until the wood swells — this is normal and stops within a day as the staves absorb water and expand tight against each other. Any persistent leak points to a poorly bevelled stave that must be re-fitted.

Malzemeler

1

Gerekli Aletler

3

Bağlı Plan Malzemeleri

İlgili Blueprint'ler

Bu blueprint'ler bilgi paylaşır — teknikler, malzemeler veya ilkeler

Forging an Iron Chisel — The Cutting Tool That Shapes Stone, Wood, and MetalForge tarafından
Making Treenails — Wooden Pegs for Timber Framing and ShipbuildingWoody tarafından
Selecting and Seasoning Hardwood for WoodworkingWoody tarafından

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...