İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER

Dog Kennel Whose Top Tilts Back on Lift-Off Hinges to Air and Clean It (Minion, 1909)
John S. Minion of Newark received US 920,975, dated 11 May 1909, for a kennel in two parts. The top half, with the roof, sits on the bottom half and hinges at the back on slotted plates and studs, so it can be tilted back to let the sun in and clean the floor, or lifted right off. A swinging arm drops down by itself to hold it open.
We build it from pine. All sizes are ours.
Orta
About 1 day
Talimatlar
1
1
Size for the dog
Size for the dog
Jupyter defteri yükleniyor…
2
2
Read US 920,975
Read US 920,975
"The upper portion can be tilted back as shown in Fig. 1 so as to permit the cleaning of the lower portion, and also allow sunlight to penetrate therein over its whole surface, which makes a sanitary structure."
3
3
Build the lower portion
Build the lower portion
Build an open box of pine boards with upright sides and a floor, his portion 10, raised on two strips 12 so air passes under it. Cut the entrance 11 in the front.
Bu adım için malzemeler:
Çam tahta1 adet
Galvanizli çiviler1 adetGerekli aletler:
Şerit Metre
El Testeresi
Kıl Testere
Marangoz çekici4
4
Build the upper portion
Build the upper portion
Build the top half, his portion 13, with sides that stand on the lower sides, a gabled roof 16, and an opening 15 matching the entrance. Nail strips 14 round its lower edge outside so they overlap the lower portion, shed water and make a tight joint.
Bu adım için malzemeler:
Çam tahta1 adet
Galvanizli çiviler1 adetGerekli aletler:
El Testeresi
Kıl Testere
Marangoz çekici5
5
Fit the lift-off hinge
Fit the lift-off hinge
Screw a flat-bar plate to the back of each lower side, projecting behind, with a slot cut in its top edge (his plates 32 and slots 33). Screw a plate with a bolt as a stud to each side of the upper portion so the studs drop into the slots when the top is set down (his plates 34 and studs 35). The top now tilts back on the studs or lifts off.
Bu adım için malzemeler:
Yumuşak Çelik Lama1 adet
Kare boyunlu yuvarlak başlı cıvata1 adet
Ahşap vidalar1 adetGerekli aletler:
Demir Testeresi
Eğe Takımı
Sütunlu Matkap
Matkap Ucu Takımı
Tornavida takımı6
6
Fit the prop arm
Fit the prop arm
Hang a flat-bar arm from a hinge at the top of the back of the upper portion (his arm 24 and hinge 23). Join its lower part to a bracket on the lower portion with a link (his link 25 and bracket 28), slotted so it can be unhooked. When the top is tilted back, the arm swings down to the ground and props it.
Bu adım için malzemeler:
Yumuşak Çelik Lama1 adet
Kapı menteşesi1 adet
Kare boyunlu yuvarlak başlı cıvata1 adet
Ahşap vidalar1 adetGerekli aletler:
Demir Testeresi
Sütunlu Matkap
Matkap Ucu Takımı
Tornavida takımı7
7
Protect the entrance
Protect the entrance
Screw a strip of flat bar round the edge of the entrance, his iron band 31, where a chained dog wears it.
Bu adım için malzemeler:
Yumuşak Çelik Lama1 adet
Ahşap vidalar1 adetGerekli aletler:
Demir Testeresi
Sütunlu Matkap
Matkap Ucu Takımı
Tornavida takımı8
8
Troubleshooting
Troubleshooting
Kennel troubleshooting.
Flow
Loading...
9
9
History and honest limits
History and honest limits
**John S. Minion** of Newark, US 920,975, dated 11 May 1909, filed 21 May 1908. He claimed "a kennel comprising a bottom portion having vertical sides, a top portion with vertical sides resting on the sides of the bottom portion, hinges connecting the sides of the bottom and top portions on one end, an arm swinging from its top end on the hinged end of the top portion, and a link pivoted to the bottom portion and to the arm". He gives no sizes; the pine, all sizes and the flat-bar and bolt fittings are ours.
Malzemeler
6- 1 adetYer Tutucu
- 2 adetYer Tutucu
- 1 adetYer Tutucu
- Yer Tutucu
- 3 adetYer Tutucu
- 1 adetYer Tutucu
Gerekli Aletler
9- 1 vendor sell this, none ship to you yetYer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
Bu planla yapılan
İlgili Blueprint'ler
Bu blueprint'ler bilgi paylaşır — teknikler, malzemeler veya ilkeler
CC0 Kamu Malı
Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.
Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.


