İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Turner's Pole Lathe with Puppets, Screw Centre and Treadle (Moxon, 1680)
Woody

Oluşturan

Woody

14. Kasım 2026NO
9
0
0
0
0

Turner's Pole Lathe with Puppets, Screw Centre and Treadle (Moxon, 1680)

The workshop pole lathe of Joseph Moxon's Mechanick Exercises: legs and twin cheeks bolted square, sliding puppets wedged through the bed, a fixed steel-pointed pike and an adjustable screw centre, a hinged treadle with a cross-treadle, and a fir pole pinned to the ceiling for the spring.
İleri
Two to three days

Talimatlar

1

His sizes

Jupyter defteri yükleniyor…
2

Read Mechanick Exercises

"The Lathe is described in Plate 12. A. This Machine is so vulgarly known..."
3

Legs and cheeks

Set up two legs about 2 ft 10 in (86 cm) high, plumb, each with a tenon on top as thick as the gap you want between the two cheeks. Lay a cheek each side of the tenons, level, and fix them: pinned, or better with an iron bolt whose square neck sits in a square hole in the near cheek, drawn up by a nut. Brace legs and cheeks to the floor and walls so nothing trembles.

Bu adım için malzemeler:

Ak meşe tahtaAk meşe tahta1 adet
Kare boyunlu yuvarlak başlı cıvataKare boyunlu yuvarlak başlı cıvata1 adet

Gerekli aletler:

El TesteresiEl Testeresi
Zıvana yuvası kalemiZıvana yuvası kalemi
Ahşap TokmakAhşap Tokmak
Kol matkabı ve ucuKol matkabı ve ucu
4

Puppets

Make two (or two or three pairs of) square puppets, strong rather than weak and as short as your work allows: the centres must stand a little more than half the work's diameter above the cheeks. Give each a tenon at the foot that slides in the gap between the cheeks, with a mortise through it below the cheeks for a tapering wedge, driven with a mallet to clamp the puppet down.

Bu adım için malzemeler:

Ak meşe tahtaAk meşe tahta1 adet
Sert ağaç kamasıSert ağaç kaması1 adet

Gerekli aletler:

El TesteresiEl Testeresi
Zıvana yuvası kalemiZıvana yuvası kalemi
Ahşap TokmakAhşap Tokmak
5

Pike and screw centre

Near the top of one puppet fix a strong iron pike with a tempered steel point. Through the other fit an iron screw in a nut in the puppet, also with a steel point, both points in one straight line facing each other. Put an iron handle 7-8 in long with a knob at each end through the screw head. Cut the puppets to square shoulders just below the pikes to carry the rest.

Bu adım için malzemeler:

Dövme demir çubukDövme demir çubuk1 adet
Kare takım çeliği çubukKare takım çeliği çubuk1 adet

Gerekli aletler:

Demirci ocağıDemirci ocağı
ÖrsÖrs
Kılavuz ve pafta takımıKılavuz ve pafta takımı
Su verme kovasıSu verme kovası
6

Rest and oil horn

Make the rest a square piece 1-1.5 in thick, 2-2.5 in broad, a little longer than the gap between the puppets. Hang a horn tip down on the outside of the right-hand puppet near the top, filled with oil, with a wooden cover and button carrying an iron wire that reaches nearly to the bottom, to oil the centre holes.

Bu adım için malzemeler:

Ak meşe tahtaAk meşe tahta1 adet
Sığır boynuzuSığır boynuzu1 adet
Demir telDemir tel1 adet
Makine yağıMakine yağı1 adet

Gerekli aletler:

El TesteresiEl Testeresi
Kol matkabı ve ucuKol matkabı ve ucu
7

Treadle and cross-treadle

Make a treadle about 2.5 in broad, 1 in thick and 3 ft (up to 4 ft) long. Nail its back end to the floor with a piece of leather, 1-1.5 ft behind the lathe and midway between the legs, so the front reaches 1.5-2 ft past the front of the lathe. Cut a square notch 1.5 in wide and 2 in long in the far end for winding the string. Fix an iron pin about 0.5 in thick, standing 1.5-2 in up, in the middle; under the cheeks fix a cross-treadle with a row of holes 2-3 in apart to take the pin.

Bu adım için malzemeler:

Ak meşe tahtaAk meşe tahta1 adet
Deri KayışDeri Kayış1 adet
Demir ÇivilerDemir Çiviler1 adet
Dövme demir çubukDövme demir çubuk1 adet

Gerekli aletler:

El TesteresiEl Testeresi
ÇekiçÇekiç
Kol matkabı ve ucuKol matkabı ve ucu
8

Pole and string

Use a fir pole, thick or thin to suit the work; if it is too stiff, thin its upper and under sides with a draw-knife. Pin the thick end to a ceiling timber with one nail so it pivots. About a foot away nail two cheeks to the joists with a batten across their foot to carry the pole. Run the string from the pole's thin end, round the work, to the treadle.

Bu adım için malzemeler:

Ahşap sırıkAhşap sırık1 adet
KordonKordon1 adet
Demir ÇivilerDemir Çiviler1 adet
Ak meşe tahtaAk meşe tahta1 adet

Gerekli aletler:

İki Saplı Yontma Bıçağıİki Saplı Yontma Bıçağı
ÇekiçÇekiç
9

Troubleshooting

Pole lathe troubleshooting.

Flow

Loading...
10

History and honest limits

From Joseph Moxon, **Mechanick Exercises**, Numb. X, Turning (1680), pp. 176-185 and Plate 12 (checked on the archive.org scan mechanickexercis00moxo). He gives no sizes for cheeks, puppets or pole; metric and the wood choices are ours.

Malzemeler

12

Gerekli Aletler

10

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...