İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER

Screw-On Rubber Head Mallet: Rubber Members on Flanged Ferrules, Cupped and Cushioned on Steel Studs (Pemmerl, 1950)
Michael Pemmerl of Chatham, New Jersey, received US 2,518,059, dated 8 August 1950, for an industrial mallet with heads that change. A threaded stud stands out of each end of the steel head, and percussion members of different hardness screw on. A soft member is moulded round a hard ferrule with flanges and a threaded bore, so it cannot pull off. A steel cup holds its inner end from bulging. A thick rubber washer between cup and head stops it working loose and soaks up the shock before it reaches the hand.
We make two rubber members from rubber sheet bonded round a flanged nut. The sizes are ours.
Orta
About 2 days
Talimatlar
1
1
Building a rubber member round its ferrule
Building a rubber member round its ferrule
Jupyter defteri yükleniyor…
2
2
Read US 2,518,059
Read US 2,518,059
"The frictional and cushioning washers 16 and 23, as interposed between the respective percussion members 14 and 17 and the mallet head 10, serve the two-fold purpose of setting up a strong frictional resistance against tendency of said percussion members to accidentally loosen or turn off the coupling studs 13 when the mallet is in use, while at the same time said washers act as impact shock absorbing means."
3
3
Turn the head 10
Turn the head 10
From 35 mm steel round bar turn a head 90 mm long between its end faces, and at each end a stud 13 12 mm across and 20 mm long; cut an M12 thread on each with the die. Drill a 20 mm eye through the middle, square to the axis, in a V-block, for the handle.
Bu adım için malzemeler:
Yumuşak çelik yuvarlak çubuk1 adet
Kesme yağı1 adetGerekli aletler:
Metal Torna Tezgâhı
3 ayaklı torna aynası
Torna kesici kalemi
Kesme kalemi
Kılavuz ve pafta takımı
Pafta kolu
Tezgah Mengenesi
Sütunlu Matkap
V Blok
Matkap Ucu Takımı
Dijital Kumpas 6 İnç
Koruyucu gözlük4
4
Ferrules 18 and cups 21-22
Ferrules 18 and cups 21-22
For each member, saw an M12 coupling nut to 30 mm and lock a 24 mm washer on it 4 mm from each end with a nut and thread locker: the flanges 19 round the threaded bore 20. Turn two cups from 45 mm bar: a base 3 mm thick with a 13 mm hole, and a skirt 12 mm deep bored 40.5 mm to embrace the member's inner end.
Bu adım için malzemeler:
Altıgen Somun6 adet
Düz Pul4 adet
Vida gevşemezi1 adet
Yumuşak çelik yuvarlak çubuk1 adetGerekli aletler:
Demir Testeresi
Tezgah Mengenesi
Kurbağacık anahtar
Metal Torna Tezgâhı
3 ayaklı torna aynası
Torna kesici kalemi
Delik işleme kateri
Kesme kalemi
Dijital Kumpas 6 İnç5
5
Build the rubber members 17
Build the rubber members 17
Scribe and cut 4 mm rubber discs 40 mm across with the knife: for each member, seven holed to the ferrule (24 mm holes level with the two flanges and 22 mm round the nut, so the discs either side trap each flange's rim) and five solid discs for the striking face. Brush contact cement on both faces, let it go touch-dry, and build the member up over its ferrule, the ferrule's end flush with the member's inner end; press it in clamps overnight and trim it round.
Bu adım için malzemeler:
Doğal kauçuk levha1 adet
Kontak Yapıştırıcı1 adetGerekli aletler:
Pusula
Maket Bıçağı
Çubuklu işkence6
6
Handle and assembly
Handle and assembly
Turn an ash handle 300 mm long, fit it in the eye with a glued wedge. Cut two 6 mm rubber washers 23, 40 mm across with 13 mm holes. On each stud put a rubber washer, then a cup, skirt outwards, then screw a member on until its end is in the cup and the washer is squeezed; it should take a firm twist to undo.
Bu adım için malzemeler:
Sert Ağaç Tahtası1 adet
Ahşap Tutkalı1 adet
Doğal kauçuk levha1 adetGerekli aletler:
Ahşap torna tezgâhı
Torna kalemi seti (HSS)
Demir Testeresi
Küre başlı çekiç
Maket Bıçağı7
7
Troubleshooting
Troubleshooting
Interchangeable-head mallet troubleshooting.
Flow
Loading...
8
8
History and honest limits
History and honest limits
**Michael Pemmerl** of Chatham, New Jersey, US 2,518,059, dated 8 August 1950, filed 31 October 1947. He claimed a mallet head with a screw-threaded coupling stud at an end, "a percussion member made of relatively soft material such as lead, an internally screw-threaded ferrule made of hard metal imbedded in said percussion member, said ferrule having external annular flanges", "a perforate cupped reenforcing member", and "a perforate rubber washer of substantial thickness" between cup and head. His soft members were moulded, and he names rubber among their materials; ours are rubber discs bonded round the ferrule. He also shows hard metal and rawhide members. He gives no sizes; every size here is ours.
Malzemeler
9- Yer Tutucu
- 1 adetYer Tutucu
- 6 adetYer Tutucu
- 4 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
Gerekli Aletler
21- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
Bu planla yapılan
İlgili Blueprint'ler
Bu blueprint'ler bilgi paylaşır — teknikler, malzemeler veya ilkeler

Renewable Rubber-Face Hammer: Rolled Faces Pressed Onto Pronged Discs, Driven Out Through a Notch When Worn (Sewell, 1928)
Forge tarafından
Metal işleme
11
0
0
0
0
0

Laminated Rubber Mallet: A Rubber-and-Canvas Head Locked on a Flared Handle by an Internal Rib (Whisler, 1924)
Forge tarafından
Ağaç işleri
11
0
0
0
0
0
CC0 Kamu Malı
Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.
Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.
