İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER

Valentine and Sweets Box: a Card Tray Stacked on a Candy Tray, With Wings That Hold the Card (Richter, 1908)
Harry Richter of Omaha received US 901,476, dated 20 October 1908, for a box with two trays under one lid: sweets below, and above them a deeper tray for a valentine, held flat by little card wings so it never touches the lid. The trays stack on an inner rim and cannot slide, and come apart easily.
We make it from pasteboard and card. All sizes are ours.
Başlangıç
About 3 hours
Talimatlar
1
1
Box sizes
Box sizes
Jupyter defteri yükleniyor…
2
2
Read US 901,476
Read US 901,476
"The device affords a secure housing for these articles, and by reason of the formation and arrangement of parts, it may be economically constructed."
3
3
Make the lower tray
Make the lower tray
Cut the bottom 1 from pasteboard and glue an upturned rim 3 round it from a card strip, scored and folded at the corners. Glue a second strip inside it, his sustaining leaf 4, standing about 6 mm (ours) above the rim all round.
Bu adım için malzemeler:
Yapıştırma mukavva1 adet
Bristol Karton1 adet
Tutkal1 adetGerekli aletler:
Kurşun kalem
Cetvel
Maket Bıçağı
Kemik katlayıcı
Tutkal fırçası4
4
Make the upper tray
Make the upper tray
Cut the bottom 6 the same size and glue a deeper rim 8 round it. Glue an enclosing strip 9 round the outside of rim 8, a little lower than it at the top and reaching about 6 mm below the bottom (his portion 10), so the upper tray sits on the lower one with the enclosing strip round the lower tray's inner rim.
Bu adım için malzemeler:
Yapıştırma mukavva1 adet
Bristol Karton1 adet
Tutkal1 adetGerekli aletler:
Cetvel
Maket Bıçağı
Kemik katlayıcı
Tutkal fırçası5
5
Make the card wings
Make the card wings
Cut two small triangular card wings, each with a folded flange 16. Glue the flanges inside rim 8, midway between the ends, one each side, so the wings can be bent down over the bottom: their lower edges 17 press on the valentine and keep it off the lid.
Bu adım için malzemeler:
Bristol Karton1 adet
Tutkal1 adetGerekli aletler:
Maket Bıçağı
Kemik katlayıcı
Tutkal fırçası6
6
Make the lid
Make the lid
Cut the top leaf 11 to fit over the upper tray and glue a rim 13 round it, sized so it rests on the enclosing strip 9, as his Fig. 4.
Bu adım için malzemeler:
Yapıştırma mukavva1 adet
Bristol Karton1 adet
Tutkal1 adetGerekli aletler:
Cetvel
Maket Bıçağı
Kemik katlayıcı
Tutkal fırçası7
7
Fill and close it
Fill and close it
Put the sweets in the lower tray, set the upper tray on it, lay the valentine in and bend the wings down over it, and put the lid on. Lift the upper tray off to reach the sweets.
8
8
Troubleshooting
Troubleshooting
Valentine box troubleshooting.
Flow
Loading...
9
9
History and honest limits
History and honest limits
**Harry Richter** of Omaha, US 901,476, dated 20 October 1908, filed 29 November 1907. He claimed a box with a lower receptacle with an inner sustaining rim, an upper receptacle with an outer enclosing rim, "flexible holding-wings having flanges secured upon the inner sides of the integral upturned rim", and a cover. He made the wings "preferably of card board" and gives no sizes: the pasteboard, all sizes and glue are ours.
Malzemeler
3- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 4 adetYer Tutucu
Bu planla yapılan
İlgili Blueprint'ler
Bu blueprint'ler bilgi paylaşır — teknikler, malzemeler veya ilkeler
CC0 Kamu Malı
Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.
Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.


