İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Stovetop Kettle: a Square Copper Kettle (Hasluck, 1907)
Forge

Oluşturan

Forge

4. Kasım 2026NO
11
0
0
0
0

Stovetop Kettle: a Square Copper Kettle (Hasluck, 1907)

A tinsmith's square kettle in sheet copper, 9 x 9 in and 3 5/8 in deep: a box body with folded corner seams, a hollowed top pened on, a brazed and bent spout, a small cover, and a wooden handle on brass uprights. Hasluck prefers copper; tinplate also works and is a separate route. Source: Paul N. Hasluck, Tinplate Work (1907), pp. 91-98. Unknown: copper gauge, solder. Picture: Figs. 188-189 of the book.
İleri
Unknown

Talimatlar

1

Cut the patterns

For a body 9 x 9 x 3 5/8 in, cut two ends 9 1/2 x 4 in and two sides 9 1/4 x 4 in, notched for box seams at the corners (Figs. 190-191), with allowances to fold at top and bottom. Punch the spout hole in the front. Cut the bottom 9 1/2 in square, notched for a 1/4 in edge. Set out the top as a 10 1/2 in square with curved allowances for hollowing and a 4 in circle for the cover hole (Fig. 193); set out the spout from the elevation (Fig. 192), the cover and its cone-shaped rim (Figs. 194-195).

Bu adım için malzemeler:

Bakır LevhaBakır Levha1 body, bottom, top, spout, cover

Gerekli aletler:

PergelPergel
ÇizecekÇizecek
Sac makasıSac makası
2

Braze and shape the spout

Thin the long edges by hammering. Set in the throat with a stretching hammer on a beak iron, bend the spout round until the edges overlap, bind it with wire, lay spelter and borax along the inside of the seam and braze it; then close and braze the under seam. Fill it with lead and bend the neck with a round-faced hammer on the hollowing block; file off spare spelter and smooth it. Run out the lead, throw off a seating round the large end, trim the top with snips and tin the inside.

Bu adım için malzemeler:

Bilinmeyen metalBilinmeyen metal1 spelter
KalayKalay1 tinning

Gerekli aletler:

Perdah çekiciPerdah çekici
KazıkKazık
Demir telDemir tel
Boraks tozuBoraks tozu
Sert lehim şalomasıSert lehim şaloması
KurşunKurşun
Delikli kevgirDelikli kevgir
Sert Ahşap BlokSert Ahşap Blok
Metal EğeMetal Eğe
Sac makasıSac makası
3

Fold and seam the body

Fold the top edges square, the front and back outwards and the sides likewise; fold the bottom edges right over inwards to take the bottom (Fig. 188). Hook each side's end over the front's and work the corner seam on a straight-edged tool (Figs. 198-199). Turn up the bottom's 1/4 in edge, push it edge-down into the bottom folds, and solder the bottom and seams.

Bu adım için malzemeler:

Kalay-kurşun lehimKalay-kurşun lehim1 adet

Gerekli aletler:

Ahşap TokmakAhşap Tokmak
KazıkKazık
Elektrikli HavyaElektrikli Havya
DekapanDekapan
4

Hollow the top and make the cover

Hollow the top on the block: sink the four sides a little, hollow the corners with a bullet-faced hammer, flatten each side along the block edge, even the shoulder and smooth it all over. Pare the edges, mark the flange with an edging machine, set it down square with a hatchet stake and mallet, and take up an edge to fit over the body. Cut the cover hole with circular snips and fit a narrow wired rim, worked over inside. Make the cover: solder its cone rim to fit the wired rim, throw off a flange, hollow the cover disc and seam it on, and fix the knob.

Bu adım için malzemeler:

Demir telDemir tel1 rim
Kalay-kurşun lehimKalay-kurşun lehim1 adet
Bilinmeyen metalBilinmeyen metal1 cover knob

Gerekli aletler:

Perdah çekiciPerdah çekici
Sert Ahşap BlokSert Ahşap Blok
KazıkKazık
Ahşap TokmakAhşap Tokmak
Sac makasıSac makası
Elektrikli HavyaElektrikli Havya
DekapanDekapan
5

Handle, top and spout

Cut two handle uprights from stout brass or copper band (Fig. 196), drill them for rivets and for the spindle that carries the wooden handle, and bend them to shape. Rivet them to the top and solder over the rivet heads inside. Pene the top down onto the body and solder along each edge. Push the spout through its hole from inside until its large end butts against the front, and solder it strongly from inside.

Bu adım için malzemeler:

Pirinç LevhaPirinç Levha1 handle uprights
Pirinç ÇubukPirinç Çubuk1 spindle
SapSap1 wood
Bakır perçinlerBakır perçinler1 number not given
Kalay-kurşun lehimKalay-kurşun lehim1 adet

Gerekli aletler:

El matkabıEl matkabı
Perçin çekiciPerçin çekici
Ahşap TokmakAhşap Tokmak
Elektrikli HavyaElektrikli Havya
DekapanDekapan

Malzemeler

9

Gerekli Aletler

17

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...