İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Watering Can: the Tinplate Rose Watering-Can (Hasluck, 1907)
Forge

Oluşturan

Forge

4. Kasım 2026NO
9
0
0
1
0

Watering Can: the Tinplate Rose Watering-Can (Hasluck, 1907)

A tinsmith's garden watering can: a round body from one sheet 2 ft 1 in x 8 1/2 in, a two-piece spout with a perforated rose, a hollowed top with a cross handle, and a back handle with a thumb ring. Tinplate or galvanised iron. Variable: the rose. Its pattern diameter is the rose diameter x 4 / 3; finer holes for seedlings. Source: Paul N. Hasluck, Tinplate Work (1907), pp. 54-57. Unknown: solder. Picture: Figs. 132-135 of the book.
Orta
Unknown

Talimatlar

1

Make the body and bottom

Cut a sheet 2 ft 1 in by 8 1/2 in. Wire one edge, sink it in the crease iron, round it and groove the seam; solder the seam inside. Cut the spout hole opposite the seam, 2 1/2 in from the bottom. Edge the bottom to fit, beat it up and solder it from inside.

Bu adım için malzemeler:

Teneke sacTeneke sac1 body, bottom
Demir telDemir tel1 edge
Kalay-kurşun lehimKalay-kurşun lehim1 adet

Gerekli aletler:

Sac makasıSac makası
KazıkKazık
Ahşap TokmakAhşap Tokmak
Elektrikli HavyaElektrikli Havya
DekapanDekapan
2

Make and fit the spout

Cut the spout in two pieces (Fig. 133), bend them to shape and solder the seams. Solder the larger piece into the body. Make it longer for plants out of reach, with an elbow for plants up high. Make the stay: a taper strip as long as the gap between can and spout, bent to a half-round section and soldered in.

Bu adım için malzemeler:

Teneke sacTeneke sac1 spout, stay
Kalay-kurşun lehimKalay-kurşun lehim1 adet

Gerekli aletler:

Sac makasıSac makası
KazıkKazık
Elektrikli HavyaElektrikli Havya
DekapanDekapan
3

Make the rose

Set out the rose body (Fig. 135): its diameter is the rose diameter x 4 / 3, so a 3 in rose needs a 4 in pattern, with lines a b at right angles. Bend it over a funnel stake and solder the seam. Hollow a disc for the front, with edges for capping on. Inside the hollow, mark circles and pierce them at intervals with a bradawl over a hard wood block; very fine for seedlings. Solder front and stem to the rose body. Several roses of different sizes are useful.

Bu adım için malzemeler:

Teneke sacTeneke sac1 rose
Kalay-kurşun lehimKalay-kurşun lehim1 adet

Gerekli aletler:

PergelPergel
Sac makasıSac makası
KazıkKazık
Perdah çekiciPerdah çekici
BizBiz
Sert Ahşap BlokSert Ahşap Blok
Elektrikli HavyaElektrikli Havya
DekapanDekapan
4

Fit the top and handles

Hollow the top (Fig. 134), fit it to the body, wire its inner arc and solder it on. Cross handle: a strip about 1 3/4 in wide, wired with No. 12 B.W.G., bent to shape; cut two holes in the top with a small sharp chisel and solder the ends inside and on top. Back handle (Fig. 136): wire and bend it, solder a small boss under its upper part, and solder it opposite the spout with a thumb ring at the top. Solder three small hollowed studs under the bottom.

Bu adım için malzemeler:

Teneke sacTeneke sac1 top, handles, studs
Demir telDemir tel1 No. 12 B.W.G.
Kalay-kurşun lehimKalay-kurşun lehim1 adet

Gerekli aletler:

Sac makasıSac makası
Perdah çekiciPerdah çekici
Çelik keskiÇelik keski
Elektrikli HavyaElektrikli Havya
DekapanDekapan
5

Clean and paint

Clean with turpentine and whiting. Give two good coats of paint: red inside and green outside suit it.

Bu adım için malzemeler:

Yağlı boyaYağlı boya2 coats

Gerekli aletler:

TerebentinTerebentin
Kalsiyum karbonat (tebeşir tozu)Kalsiyum karbonat (tebeşir tozu)

Malzemeler

4

Gerekli Aletler

12

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...