İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
16 ft Canvas-Covered Cedar Canoe: Backbone, Seven Molds, Cedar Ribs and Planking, Glued Canvas (Boy Mechanic, 1919)
Woody

Oluşturan

Woody

13. Kasım 2026NO
13
0
0
0
0

16 ft Canvas-Covered Cedar Canoe: Backbone, Seven Molds, Cedar Ribs and Planking, Glued Canvas (Boy Mechanic, 1919)

Stillman Taylor's open Canadian canoe from The Boy Mechanic, Book 3 (1919): about 16 ft long, 31 in beam, 60 to 70 lb. Built upside down over a backbone and seven paper-pattern molds, with oak or ash stems, keelson and gunwales, 1/8 in cedar ribs and planking fastened with copper clout nails, then covered with No. 6 canvas laid in melted marine glue, painted, and varnished. Every layout dot and width is his, as printed.
İleri
Several weeks

Talimatlar

1

His layout data

Jupyter defteri yükleniyor…
2

Read The Boy Mechanic, Book 3

"Working with light materials, the canoe builder must pay particular attention to the workmanship ... the work must not be hurried, but plenty of time taken to do each and every part well."
3

Get the materials

Stem: oak or ash 6 ft x 3/4 in square. Keelson: oak or ash 14 ft x 3-1/2 x 3/8 in. Gunwales: 2 of oak or ash 16 ft x 7/8 x 1/2 in. Seat risings: 2 of oak or ash 1/2 in square. Fenderwales: 34 ft of 1/2 in half-round molding. Outside keel (optional): oak 14 ft x 1 x 1/2 in. Deck beams: 2 of oak or ash 8 x 1-1/8 x 3/8 in. Seat frames: 2 at 30 x 3 x 3/4 and 2 at 12 x 2-1/4 x 3/4 in. Planking: cedar or pine, 100 sq ft, 1/8 in (25 ft of 1 in lumber dressed to 1/8 in, in 12, 14 and 16 ft lengths). Ribs: 360 running ft of cedar 1-3/4 x 1/8 in. Breast hooks: cedar or oak 32 x 9 x 3/4 in. Backbone, molds and ribbands from any cheap stuff. Fastenings: 1 lb 2 in wire nails; 1 lb 5/8 in and 1/2 lb 3/4 in copper clout nails; 18 brass screws 1-1/4 in No. 8 and 24 brass screws 1 in No. 6; 4 lb marine glue; 3 oz No. 2 copper tacks; 11-3/4 yd No. 6 canvas; 1 lb 3/8 in copper tacks. Rock elm or fir may replace oak or ash; spruce, pine, cypress or fir may replace cedar.

Bu adım için malzemeler:

Ak meşe tahtaAk meşe tahta4 adet
Sedir tahtasıSedir tahtası6 adet
Çam tahtaÇam tahta3 adet

Gerekli aletler:

Boyuna kesme testeresiBoyuna kesme testeresi
El TesteresiEl Testeresi
El rendesiEl rendesi
Şerit MetreŞerit Metre
4

Lay out the backbone and molds

Cut the backbone from a 16 ft x 4 x 7/8 in board, top edge 15 ft 8-3/4 in, and mark the mold stations from each end: 22-1/4 in to mold 1, then 23-1/4 in to mold 2 and 23-1/4 in to mold 3, each mold space 3/4 in thick; mold 4 sits at the centre; cut the ends off on the bevel (Fig. 1). Draw each mold on stiff paper from his rectangles, mortises and dots (notebook), trace the curve through the dots, cut out the half, fold and draw the other side, and cut the molds from 7/8 in stock: seven in all, numbered alike from each end: two No. 1, two No. 2 (each in halves), two No. 3 and one No. 4; nail battens across the halves.

Bu adım için malzemeler:

Çam tahtaÇam tahta2 adet
Kalın kâğıt tabakalarıKalın kâğıt tabakaları1 adet
ÇivilerÇiviler1 adet

Gerekli aletler:

El TesteresiEl Testeresi
Kıl TestereKıl Testere
CetvelCetvel
Kurşun kalemKurşun kalem
MakasMakas
ÇekiçÇekiç
5

Bend the stems and shape the keelson

Make the stem mold from his Fig. 6 pattern (24-1/2 x 12 in rectangle, dots in the notebook) and bend the straight-grained 3/4 in square oak or ash stems on it. Cut the keelson 13 ft 11 in long, tapering from 3-1/2 in at the centre: 3-1/2 in at 1 and 2 ft, 3-1/4, 2-5/8, 2 and 1-1/4 in at 3 to 6 ft, and 15/16 in at the ends (Fig. 7). Fasten each stem to the keelson with a couple of 3/4 in No. 10 screws.

Bu adım için malzemeler:

Ak meşe tahtaAk meşe tahta2 adet
Pirinç ahşap vidasıPirinç ahşap vidası4 adet

Gerekli aletler:

İki Saplı Yontma Bıçağıİki Saplı Yontma Bıçağı
El rendesiEl rendesi
El TesteresiEl Testeresi
Kol matkabı ve ucuKol matkabı ve ucu
Düz tornavidaDüz tornavida
C işkenceC işkence
6

Set up the frame

Build it upside down: set the backbone on boxes about 1 ft or more off the floor and the molds in their numbered places, the backbone resting in their top mortises. True the molds with a square and toenail them. Lay the keelson in its mortises, fit the stems to the backbone angle and nail through the mold tops into them. Bevel the stem splice from the inside, leaving the outer edge about 1/8 in wide. Put on the gunwales at the sheer line with nails left proud, then four ribbands a side at 5 in centres from the keel, fastened with 1-1/4 in brads.

Bu adım için malzemeler:

Ak meşe tahtaAk meşe tahta2 adet
Çam tahtaÇam tahta1 adet
ÇivilerÇiviler1 adet

Gerekli aletler:

Marangoz gönyesiMarangoz gönyesi
ÇekiçÇekiç
Marangoz keskileriMarangoz keskileri
El rendesiEl rendesi
7

Rib the hull

Saw cedar ribs 1-3/4 in wide and 1/8 in thick, cut to length gunwale to gunwale over the ribbands. Space them 3 in apart on centres along the keelson, one over each mold. Fasten each rib to the outside of the keelson with two 5/8 in copper clout nails, spring it in under the ribbands and fasten it to the gunwales. Then remove the ribbands.

Bu adım için malzemeler:

Sedir tahtasıSedir tahtası2 adet
Geniş başlı bakır çiviGeniş başlı bakır çivi1 adet

Gerekli aletler:

El TesteresiEl Testeresi
ÇekiçÇekiç
Şerit MetreŞerit Metre
8

Plank the hull

Plank with 1/8 in cedar, bent cold, full length stem to stem, butted edge to edge without bevel, about 3 in wide; begin with the garboard strake at the keel and end with the sheer strake level with the gunwale. Punch nail holes with an awl, staggered along the ribs; clamp the plank, drive copper clout nails and clinch them inside on a clinch iron. Trim the plank ends to the stems and gunwales, saw the backbone in two to take out the frame, tack strips across the gunwales against sagging, and nail where the molds were.

Bu adım için malzemeler:

Sedir tahtasıSedir tahtası4 adet
Geniş başlı bakır çiviGeniş başlı bakır çivi1 adet
Bakır raptiye çivisiBakır raptiye çivisi1 adet

Gerekli aletler:

BizBiz
C işkenceC işkence
Çivi kıvırma demiriÇivi kıvırma demiri
ÇekiçÇekiç
El TesteresiEl Testeresi
9

Fit risings, seats, decks and thwarts

Nail 1/2 in square oak or ash seat risings, 14 ft long, about 4 in below the gunwale, boring first and clinching inside. Make the seat frames as Fig. 10 and cane them or tack on canvas (a kneeling paddler may use a 4 or 5 in seat bar instead). Notch the 8 x 1-1/8 x 3/8 in deck beams to wedge about 1/2 in against the gunwales (Fig. 11) and fix each with a 1-1/4 in No. 10 screw through the gunwale. Shape the decks 16 x 8 in (Fig. 12) and fix them with three 1-1/4 in No. 10 screws into the beam and three along each gunwale. Screw a centre thwart of oak or ash, 3/8 in thick, 2 in tapering to 1 in, under the gunwales amidships; extra thwarts behind the forward seat and about 3 ft forward of the rear seat stiffen it.

Bu adım için malzemeler:

Ak meşe tahtaAk meşe tahta2 adet
Sedir tahtasıSedir tahtası1 adet
Geniş başlı bakır çiviGeniş başlı bakır çivi1 adet
Pirinç ahşap vidasıPirinç ahşap vidası30 adet
Kanvas kumaşKanvas kumaş1 adet

Gerekli aletler:

Kol matkabı ve ucuKol matkabı ve ucu
Düz tornavidaDüz tornavida
El TesteresiEl Testeresi
Marangoz keskileriMarangoz keskileri
ÇekiçÇekiç
10

Lay the canvas

Lay the No. 6 canvas smoothly on the hull and trim it to fold at the stems (Fig. 13). Melt the black marine glue in a can over a moderately hot fire and spread a fairly heavy coat over one side of the canvas with a stiff brush. Lay it on and iron it with a moderately hot flatiron so the glue melts into the planking. Tack the edges along the gunwales and fold the canvas smoothly at the stems, tacking exactly down the stem centre line.

Bu adım için malzemeler:

Kanvas kumaşKanvas kumaş1 adet
Denizcilik tutkalıDenizcilik tutkalı1 adet
Bakır raptiye çivisiBakır raptiye çivisi1 adet

Gerekli aletler:

Teneke kutuTeneke kutu
Geniş boya fırçasıGeniş boya fırçası
Demir ütüDemir ütü
MakasMakas
ÇekiçÇekiç
11

Fenders, stem bands and keel

Tack 1/2 in round molding over the canvas edge (or a 1 in strip of planking with 1-1/4 in brads every 2 or 3 in). Put on stem bands of wood about 3/8 in square, rounded, with 1-1/4 in brads, or better, 3/8 in brass oval stem band with 3/4 in screws. An outside keel is optional: about 1 x 1/2 in of oak or ash tapered to the stem bands, or a flat keel about 2-1/2 in wide of 3/8 in oak or ash, which turns more easily and guards the bottom.

Bu adım için malzemeler:

Yarım yuvarlak ahşap pervazYarım yuvarlak ahşap pervaz1 adet
Pirinç baş bodoslama şeridiPirinç baş bodoslama şeridi2 adet
Pirinç ahşap vidasıPirinç ahşap vidası12 adet
Ak meşe tahtaAk meşe tahta1 adet
ÇivilerÇiviler1 adet

Gerekli aletler:

ÇekiçÇekiç
Düz tornavidaDüz tornavida
El rendesiEl rendesi
El matkabıEl matkabı
12

Paint and finish

Give the canvas a coat of shellac to waterproof it, then four coats of paint to fill the fibres, rubbing down the second and third with fine sandpaper. Finish all woodwork with three coats of good outside spar varnish. A removable slatted grating of soft-pine lattice, about 1-1/8 in wide and 1-1/4 in thick as printed, screwed to curved cross strips (not the ribs), protects the bottom.

Bu adım için malzemeler:

Gomalak vernikGomalak vernik1 adet
Yağlı boyaYağlı boya1 adet
Zımpara KağıdıZımpara Kağıdı1 adet
Seren verniğiSeren verniği1 adet
Çam tahtaÇam tahta1 adet

Gerekli aletler:

Geniş boya fırçasıGeniş boya fırçası
Düz tornavidaDüz tornavida
13

Troubleshooting

Canoe troubleshooting.

Flow

Loading...
14

History and honest limits

From "How to Build a Canoe, Part I" by Stillman Taylor, in **The Boy Mechanic, Book 3**, Popular Mechanics, 1919 (Project Gutenberg 71856; checked on the archive.org scan boymechanic0003unse, pp. 77-84). As printed, his text differs in places: the backbone's lower edge is 1/2 in longer in one sentence and 1 in in the next; the list gives No. 8 deck screws, the text No. 10; the list's seat frames (30 x 3 and 12 x 2-1/4 in) differ from Fig. 10 (29 x 9 in); the fenders are half-round in the list and round in the text. The metric figures are ours.

Malzemeler

16

Gerekli Aletler

21

Bu planla yapılan

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...