İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER

Sliding-Table Saw That Switches Itself: A Hand Saw Under a Table on Balls, Turned On and Off by the Stroke (Tracy, 1941)
Mearl V. Tracy of Sacramento received US 2,260,421, dated 28 October 1941, for a light table saw to take onto a building job. An ordinary electric hand saw hangs under a table that slides on steel balls in channels. The work is held against a fixed fence and the table carries the saw through it. A springy finger on the table trips a snap switch, starting the saw just before it reaches the work and stopping it as the table comes back. One fence on a graduated plate serves as rip fence and mitre gauge.
The patent gives no sizes; every size here is ours, and our box is plywood where his is sheet metal.
Orta
About 3 days
Talimatlar
1
1
Where the switch must trip
Where the switch must trip
Jupyter defteri yükleniyor…
2
2
Read US 2,260,421
Read US 2,260,421
"The finger 25 is so disposed as to engage trigger 24 and close the switch when the table is advanced and just before the saw reaches the work under which the table slides, and to reengage the trigger and open the switch as the table retracts and approaches a fully retracted position."
3
3
The box frame
The box frame
Make an open-topped box of 18 mm plywood 900 mm long, 450 wide and 300 high, the end panels 2 standing 40 mm lower than the sides 1, glued and screwed. Bolt a steel channel section 5 along the inside top of each side, its open face inwards, as his channels on the beams 4.
Bu adım için malzemeler:
Kontrplak levha1 adet
Çelik U profil2 adet
Altıköşe cıvata takımı8 adet
Altıgen Somun8 adet
Ahşap vidalar30 adet
Ahşap Tutkalı1 adetGerekli aletler:
Dekupaj Testere
Kablosuz Matkap
Matkap Ucu Takımı
Çubuklu işkence
Kombine Gönye
Şerit Metre
Demir Testeresi
Kurbağacık anahtar4
4
The sliding table
The sliding table
Cut the table 6 from 18 mm plywood 600 x 400 mm with a saw slot 15 down its middle, and bolt a steel channel section 7 along each side edge, its open face outwards opposite the box's channel, reaching 100 mm past the table's front for the handle. Lay 10 mm steel balls 8 between each pair of opposed channels, three a side, spaced along, and slide the table in so it runs level with the box's top. Fit a hardwood handle 9 across the angles' front ends, and stops 10, 11 and 12 to limit the stroke to 450 mm.
Bu adım için malzemeler:
Kontrplak levha1 adet
Çelik U profil2 adet
Bilyalı rulmanlar1 adet
Sert Ağaç Tahtası1 adet
Altıköşe cıvata takımı8 adet
Altıgen Somun8 adet
Ahşap vidalar12 adetGerekli aletler:
Dekupaj Testere
Kablosuz Matkap
Matkap Ucu Takımı
Demir Testeresi
Eğe Takımı
Kurbağacık anahtar
Kombine Gönye5
5
Hang the saw under the table
Hang the saw under the table
Bolt the circular saw by its own base plate under the table, the blade up through the slot, the saw's depth set so the blade stands 10 mm above the thickest work. For angle cuts use the saw's own bevel adjustment, which does what his arcuate bracket 17 did. Tape or lock the saw's trigger on, so the new switch alone controls it.
Bu adım için malzemeler:
Daire testere1 adet
Altıköşe cıvata takımı4 adetGerekli aletler:
Kablosuz Matkap
Matkap Ucu Takımı
Kurbağacık anahtar
Kombine Gönye6
6
The self-acting switch
The self-acting switch
Screw a lever microswitch rated for the saw's current inside one side panel, its lever 24 pointing up into the path of the table, with an outlet for the saw's plug and a supply cord through the panel, as his switch box 22 and socket; have it wired by an electrician. Bend a finger 25 of spring steel and screw it on a bracket 26 under the table, set so that, as the table goes forward, it flips the lever on 60 mm into the stroke, and as the table comes back it flips it off 40 mm before the end. Check it with the saw unplugged: you should hear the click each way.
Bu adım için malzemeler:
Mikroanahtar (kollu)1 adet
Yay çeliği şeridi1 adet
Yumuşak Çelik Lama1 adet
Ahşap vidalar6 adetGerekli aletler:
Sac makası
Tezgah Mengenesi
Kablosuz Matkap
Matkap Ucu Takımı
Tornavida takımı7
7
Rip fence and mitre gauge
Rip fence and mitre gauge
Cut a half-round steel plate 27 to lie over the front of the box beside the saw, turn its straight edge up as a flange 28 and bolt a hardwood fence 29 to it, notched 30 for the blade. Pivot a link 31 on top of the plate and a link 32 under it at the centre of its arc; pivot a third link 33 on 31's end; take 32 and 33 back to a flange on the side of the box. Mark the plate in degrees and drill rows of holes along the arcs, and set the fence with a pin through link 31 into a hole, clamped by two wing-nut clamps 35, 36.
Bu adım için malzemeler:
Yumuşak Çelik Sac1 adet
Sert Ağaç Tahtası1 adet
Yumuşak Çelik Lama2 adet
Yumuşak çelik yuvarlak çubuk1 adet
Altıköşe cıvata takımı6 adet
Kanatlı somun2 adetGerekli aletler:
Sac makası
Demir Testeresi
Tezgah Mengenesi
Sütunlu Matkap
Matkap Ucu Takımı
İletki
Çizecek
Nokta Zımbası
Eğe Takımı8
8
Cut
Cut
With the table fully back, hold a board against the fence with one hand and push the handle with the other. The saw starts by itself before the blade reaches the board, cuts through, and stops as you bring the table back.
Gerekli aletler:
Koruyucu gözlük
Kulak koruyucu (kulaklık, SNR 30 dB)9
9
Troubleshooting
Troubleshooting
Sliding table saw troubleshooting.
Flow
Loading...
10
10
History and honest limits
History and honest limits
**Mearl V. Tracy** of Sacramento, California, assignor of one-half to Marion M. Tracy, US 2,260,421, dated 28 October 1941, filed 18 April 1938. His one claim is the switch: a snap switch with a trigger moved one way or the other by "a resilient finger mounted on the table" that then passes and leaves the trigger, near but before each end of the stroke. He removed the hand saw's shoe and fixed its mounting block on an arcuately slotted bracket; modern saws differ, so we mount it by its base plate and use its own bevel adjustment. His box is sheet metal with the channels on bent beams; ours is plywood with steel channel sections. He gives no sizes; every size here is ours.
Malzemeler
15- 1 adetYer Tutucu
- 2 adetYer Tutucu
- 26 adetYer Tutucu
- 16 adetYer Tutucu
- 48 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 2 adetYer Tutucu
- 1 adetYer Tutucu
- Yer Tutucu
- 2 adetYer Tutucu
Gerekli Aletler
18- 1 vendor sell this, none ship to you yetYer Tutucu
- 1 vendor sell this, none ship to you yetYer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- 1 vendor sell this, none ship to you yetYer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
Bu planla yapılan
İlgili Blueprint'ler
Bu blueprint'ler bilgi paylaşır — teknikler, malzemeler veya ilkeler

Foot-Fed Carriage Saw Table: The Saw Rides on Balls Under the Table, a Foot Lever Pulls It Through the Work (Hall, 1933)
Forge tarafından
Ağaç işleri
8
0
0
0
0
0

Portable Bench Saw: A Lift-Out Power Unit on Trunnions, Its Motor on Spring Bars, Under a Tilting Platform (Henkel, 1928)
Forge tarafından
Ağaç işleri
9
0
0
0
0
0
CC0 Kamu Malı
Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.
Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.
