SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Twisted-Strip Egg Beater: Faces Beat and Edges Cut
A wire beater passes through the egg and leaves a wake without much froth.
James P. McLean and Philemon A. Morley of Brooklyn received US 28,760, dated 19 June 1860, for an egg beater of corrugated or twisted strips of tin turned inside a can by a large and a small cog gear set between the double heads of its lid: "by means of twisted or corrugated strips of metal the gelatin mass is beaten by the flat surfaces as well as being broken or cut by the sharp edges thereof."
This rung works out how much of a twisted face pushes, then prints the gears and a cage of twisted strips, builds the lid drive on a can, and times a beating.
Orta
About 4 hours, plus printing
Talimatlar
1
1
How a twisted face beats
How a twisted face beats
Jupyter defteri yükleniyor…
2
2
A geared wire beater before it
A geared wire beater before it
The embedded blueprint beats with bent wires. McLean and Morley use twisted strips with faces and edges.
3
3
Read US 28,760
Read US 28,760
"The superiority of our arrangement of egg beaters over those that are in common use, is that by means of twisted or corrugated strips of metal the gelatin mass is beaten by the flat surfaces as well as being broken or cut by the sharp edges thereof, hence the action is analogous to the motion produced by the hand and spoon, whereas an ordinary wire beater simply passes through the egg like the rudder of a boat, leaving a simple wake behind it without producing an immediate fomentation as is the case with our beater."
4
4
Print the gears and cage
Print the gears and cage
Print the 36-tooth gear (/uploads/blueprints/twisted-strip-egg-beater-gear-36.stl), the 12-tooth gear (/uploads/blueprints/twisted-strip-egg-beater-gear-12.stl) and the cage of four twisted strips (/uploads/blueprints/twisted-strip-egg-beater-cage.stl). Print in PETG at 0.2 mm layers, 30 % infill, 4 walls.
Bu adım için malzemeler:
PETG filament1 adetGerekli aletler:
FDM 3B yazıcı5
5
Make the double lid
Make the double lid
Cut two plywood disks to the can's mouth. Space them 20 mm apart on three M5 screws with nuts, and drill both for the crank shaft and the cage shaft 48 mm apart.
Bu adım için malzemeler:
Kontrplak levha1 adet
Makine vidaları1 adet
Altıgen Somun1 adet
Düz Pul1 adetGerekli aletler:
Kıl Testere
Kablosuz Matkap
Matkap Ucu Takımı
Kurbağacık anahtar
Dijital Kumpas 6 İnç6
6
Fit the shafts and gears
Fit the shafts and gears
Epoxy the large gear on a crank shaft of 5 mm rod with a bent handle, and the small gear on the cage shaft, both between the heads. Epoxy the cage on the cage shaft's lower end.
Bu adım için malzemeler:
Yumuşak Çelik Çubuk1 adet
İki bileşenli epoksi1 adetGerekli aletler:
Demir Testeresi
Tezgah Mengenesi
Yassı Ağızlı Pense7
7
The patent drawing
The patent drawing
US 28,760 drawing sheet, public domain (expired patent).
8
8
Beat egg whites
Beat egg whites
Put two egg whites in the can, fit the lid, and crank about once a second; time to stiff peaks.
Bu adım için malzemeler:
Teneke kutu1 adet
Yumurta2 adetGerekli aletler:
Kronometre9
9
Gears that skip, a cage that scrapes
Gears that skip, a cage that scrapes
Twisted-strip egg beater troubleshooting.
Flow
Loading...
10
10
History and honest limits
History and honest limits
**James P. McLean** and **Philemon A. Morley** of Brooklyn, assignors to P. A. Morley, received US 28,760, dated 19 June 1860. Their Fig. 2, for bakers, puts the strips on a vertical water-tight cylinder turning round a stationary handle, driven by a hand wheel whose rubber band grips the cylinder's grater-like funnel top instead of cog wheels. They claimed the twisted beaters in combination with the cylinder.
**Honest limits.** FDM prints hold food in their layer lines, so wash well and replace when worn. Printed strips and plywood heads stand in for tin. Your times are the result.
Malzemeler
9- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 2 adetYer Tutucu
Gerekli Aletler
10- Yer Tutucu
- Yer Tutucu
- 1 vendor sell this, none ship to you yetYer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
İlgili Blueprint'ler
Bu blueprint'ler bilgi paylaşır — teknikler, malzemeler veya ilkeler
Counter-Rotating Egg Beater: One Wheel, Two Beaters Turning Opposite Ways
Martin tarafından
YİYECEK & İÇECEK
17
0
0
0
0
0
Stepped Spiral Egg Beater: A Stepped Dasher Spun in a Square Box
Martin tarafından
YİYECEK & İÇECEK
8
0
0
0
0
0
Gear Trains: Idlers, Compounding and Hitting a Given Ratio
Martin tarafından
Mekanik
26
0
0
0
0
0
CC0 Kamu Malı
Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.
Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.