İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Reversible-Tip Soft-Face Hammer: Domed Rubber Tips Locked in Screw-On Sockets by an Internal Rib (West & Robinson, 1962)
Forge

Oluşturan

Forge

13. Kasım 2026NO
13
0
0
0
0

Reversible-Tip Soft-Face Hammer: Domed Rubber Tips Locked in Screw-On Sockets by an Internal Rib (West & Robinson, 1962)

Robert F. West and Walter H. Robinson of Connecticut received US 3,040,792, dated 26 June 1962, for The Stanley Works. A tubular socket screws onto a threaded boss at each end of the hammer's head. A rubber tip, domed at both ends, is pushed into the socket past an internal rib, which bites into it, and its rubber fills short grooves so it cannot turn. The tip can be pulled out and turned round to use its other end. On its first blows the tip's inner face squeezes into an off-centre hole in the boss and forms its own dowel, which stops the socket unscrewing. The patent gives no sizes; every size here is ours.
İleri
About 2 days

Talimatlar

1

The tip's proportions

Jupyter defteri yükleniyor…
2

Read US 3,040,792

"Upon being subjected to the percussive forces during initial use, some of the plastic material of the inner face 27 of the striking tip 26 will be extruded or forced into the eccentrically located recess 12 in the boss surface 10 to provide a self-forming dowel pin 28 which effectively prevents inadvertent loosening of the threaded connection between boss and mounting socket during use."
3

Turn the head 2

From 35 mm steel bar turn a body 4 80 mm long with a boss 8 20 mm across and 15 mm long at each end; cut M20 threads on the bosses with the die. In each boss's end face drill a recess 12 4 mm across and 4 mm deep, 6 mm off centre. Drill a 20 mm handle eye 6 through the middle in a V-block.

Bu adım için malzemeler:

Yumuşak çelik yuvarlak çubukYumuşak çelik yuvarlak çubuk1 adet
Kesme yağıKesme yağı1 adet

Gerekli aletler:

Metal Torna TezgâhıMetal Torna Tezgâhı
3 ayaklı torna aynası3 ayaklı torna aynası
Torna kesici kalemiTorna kesici kalemi
Kesme kalemiKesme kalemi
Kılavuz ve pafta takımıKılavuz ve pafta takımı
Pafta koluPafta kolu
Tezgah MengenesiTezgah Mengenesi
Sütunlu MatkapSütunlu Matkap
V BlokV Blok
Matkap Ucu TakımıMatkap Ucu Takımı
Nokta ZımbasıNokta Zımbası
Dijital Kumpas 6 İnçDijital Kumpas 6 İnç
Koruyucu gözlükKoruyucu gözlük
4

Turn the sockets 14

From 48 mm bar turn two sockets 30 mm long. Knurl the outside 25. Drill and tap the collar end 18 M20, 8 mm deep. From the other end, before boring, drill four 4 mm holes 20 mm deep centred on a 38 mm circle, for the grooves 24. Bore the aperture 16 38 mm across and 20 mm deep, leaving a rib 22 4 mm wide 10 mm in, turned to 35 mm with 30 degree ramps either side.

Bu adım için malzemeler:

Yumuşak çelik yuvarlak çubukYumuşak çelik yuvarlak çubuk2 adet
Kesme yağıKesme yağı1 adet

Gerekli aletler:

Metal Torna TezgâhıMetal Torna Tezgâhı
3 ayaklı torna aynası3 ayaklı torna aynası
Torna kesici kalemiTorna kesici kalemi
Delik işleme kateriDelik işleme kateri
Kesme kalemiKesme kalemi
Tırtıl çekme aletiTırtıl çekme aleti
Sütunlu MatkapSütunlu Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Kılavuz ve pafta takımıKılavuz ve pafta takımı
Kılavuz koluKılavuz kolu
Dijital Kumpas 6 İnçDijital Kumpas 6 İnç
5

Make the tips 26

For each tip, cut nine discs of 4 mm natural rubber sheet 40 mm across and bond them into a stack with contact cement; clamp it overnight. Grind it round to 38.5 mm on the belt sander, then dome both ends: a large curve over most of the face and a small round where it meets the side, the same at both ends, 36 mm long overall.

Bu adım için malzemeler:

Doğal kauçuk levhaDoğal kauçuk levha1 adet
Kontak YapıştırıcıKontak Yapıştırıcı1 adet

Gerekli aletler:

PusulaPusula
Maket BıçağıMaket Bıçağı
Çubuklu işkenceÇubuklu işkence
Bant zımpara makinesiBant zımpara makinesi
Dijital Kumpas 6 İnçDijital Kumpas 6 İnç
6

Assemble

Turn an ash handle to drive into the eye and wedge it. Screw a socket onto each boss hand-tight. Push a tip into each socket, squeezing it past the rib in the vice between soft packing, until its inner dome bears on the boss. Give the first few blows on a wood block: the rubber pushes into the boss's recess and locks the socket. To turn a tip round, pull it out, reverse it and push it back.

Bu adım için malzemeler:

Sert Ağaç TahtasıSert Ağaç Tahtası1 adet
Ahşap TutkalıAhşap Tutkalı1 adet

Gerekli aletler:

Ahşap torna tezgâhıAhşap torna tezgâhı
Torna kalemi seti (HSS)Torna kalemi seti (HSS)
Demir TesteresiDemir Testeresi
Küre başlı çekiçKüre başlı çekiç
Tezgah MengenesiTezgah Mengenesi
7

Troubleshooting

Reversible-tip hammer troubleshooting.

Flow

Loading...
8

History and honest limits

**Robert F. West** of Simsbury and **Walter H. Robinson** of West Hartford, Connecticut, assignors to The Stanley Works, US 3,040,792, dated 26 June 1962, filed 31 August 1960. They claimed sockets with an internal portion of reduced cross-section whose surfaces are "inclined to provide ramp surfaces", and symmetrical tips "having end surfaces of convexly curvilinear configuration", removable and "reversible in said sleeves". They list natural rubber, synthetic rubbers, nylon and cellulose esters for the tips; ours are laminated natural rubber. They give proportions but no sizes; every size here is ours.

Malzemeler

6

Gerekli Aletler

24

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...