İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER

Cam-Lock Drill-Press Vise: Holed Steel Bed, Pinned Jaws and an Eccentric Cam (Popular Mechanics, 1920)
C. H. Willey's quick-acting vise for the drill-press table (Popular Mechanics, 1920): a 1/2 x 3 in. steel bed drilled with 5/8 in. holes 7/8 in. apart and bolted down on slotted end pieces, a fixed jaw pinned into any hole, a sliding jaw kept on the bar by a riveted cross pin, and an eccentric cam on a handle that locks the work.
Orta
A day
Talimatlar
1
1
The steps
The steps
Jupyter defteri yükleniyor…
2
2
Read Willey
Read Willey
"A very efficient, quick-opening and closing vise for the drill-press table."
3
3
Make the bed
Make the bed
Cut a bed bar from 1/2 x 3 in. (13 x 76 mm) steel to suit your table (length ours). Drill a row of 5/8 in. (16 mm) holes 7/8 in. (22 mm) apart along its middle.
Bu adım için malzemeler:
Yumuşak Çelik Lama1 adetGerekli aletler:
Demir Testeresi
Nokta Zımbası
Sütunlu Matkap
Matkap Ucu Takımı4
4
Make the end supports
Make the end supports
Cut two short pieces of the same stock, slot them for bolts to the drill-press table and fix one under each end of the bed (ours: bolted), so the bed stands clear of the table.
Bu adım için malzemeler:
Yumuşak Çelik Lama1 adet
Altıköşe cıvata takımı1 adetGerekli aletler:
Demir Testeresi
Sütunlu Matkap
Matkap Ucu Takımı
Eğeler (El Eğesi)5
5
Make the fixed jaw
Make the fixed jaw
Cut out a steel block underneath so it straddles the bed (stock and size ours). Drive a pin into it, downward, that fits the 5/8 in. holes.
Bu adım için malzemeler:
Yumuşak Çelik Lama1 adet
Yumuşak Çelik Çubuk1 adetGerekli aletler:
Demir Testeresi
Eğeler (El Eğesi)
Sütunlu Matkap
Matkap Ucu Takımı
Küre başlı çekiç6
6
Make the sliding jaw
Make the sliding jaw
Cut a second block the same way. Pass a horizontal pin across the opening below the bed and rivet it to the jaw's sides, so the jaw slides along the bar but cannot lift off.
Bu adım için malzemeler:
Yumuşak Çelik Lama1 adet
Yumuşak Çelik Çubuk1 adetGerekli aletler:
Demir Testeresi
Eğeler (El Eğesi)
Sütunlu Matkap
Matkap Ucu Takımı
Küre başlı çekiç
Tezgah Mengenesi7
7
Make the cam
Make the cam
Saw a disk off steel shafting. Drive a pin that fits the 5/8 in. holes into one face, off centre. At right angles to it, drill a hole in the rim and fit a handle.
Bu adım için malzemeler:
Çelik mil1 adet
Yumuşak Çelik Çubuk1 adetGerekli aletler:
Demir Testeresi
Sütunlu Matkap
Matkap Ucu Takımı
Küre başlı çekiç8
8
Use it
Use it
Bolt the bed to the table. Set the fixed jaw's pin in the hole that suits the work, slide the jaw up, drop the cam pin into the hole behind it and swing the handle to lock the work.
Bu adım için malzemeler:
Altıköşe cıvata takımı1 adetGerekli aletler:
Sütunlu Matkap9
9
Troubleshooting
Troubleshooting
Drill vise troubleshooting.
Flow
Loading...
10
10
History and honest limits
History and honest limits
From C. H. Willey, "A Simple Drill Vise", **Popular Mechanics** vol. 34 (November 1920), p. 3340 (checked on the archive.org scan of Popular Mechanics Shop Notes, popularmechanic00unkngoog). He gives only the bed section and the hole size and spacing; jaw and cam sizes, the bar length, how the end pieces are fixed and the cam offset are ours.
Malzemeler
4- 1 adetYer Tutucu
- 2 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
Bu planla yapılan
İlgili Blueprint'ler
Bu blueprint'ler bilgi paylaşır — teknikler, malzemeler veya ilkeler
CC0 Kamu Malı
Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.
Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.


