İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Valve-and-Cap Churn Dasher: Cream Driven Through Hinged Valves and Out of a Perforated Top Against a Sliding Cap
Buttercup

Oluşturan

Buttercup

10. Kasım 2026IE
7
0
0
0
0

Valve-and-Cap Churn Dasher: Cream Driven Through Hinged Valves and Out of a Perforated Top Against a Sliding Cap

Parker Wineman of Loydsville, Ohio, received US 24,898, dated 26 July 1859, for a churn dasher that is itself a closed vessel. Pushed down, it takes cream in under hinged valves on its sides; the cream mingles with the air inside and is driven out through the holes of its perforated top against a cap that slides on the shaft up to a stop. The butter falls to the bottom of the dasher, and a segment of it is taken out to remove the butter. This rung prints the dasher for a 20-litre bucket.
Orta
About 1 day, plus printing

Talimatlar

1

Where the cream stands

Jupyter defteri yükleniyor…
2

An up-and-down dasher, before it

Lake's dashers cut the cream with notched boards. Wineman's dasher takes the cream inside it and drives it out against a cap.
3

Read US 24,898

"As the dasher is forced downward, the cream is forced under the valves (d) into the dasher, where it instantly mingles with the contained air, and is forced through the perforations (i) of the top of the dasher (c) against the cap with such violence as to burst the particles of cream or milk in which the butter is contained."
4

Print the dasher body

The octagonal dasher B, 160 mm across flats and 190 mm tall, closed at the floor, with two ports, the hinge lugs, the hub for the shaft and the opening for the side panel. Print it standing on its floor. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Tasarım DosyasıSTLCC0 - Free
5

Print the perforated top c

The top c with 56 holes of 6 mm, a lip that drops into the body and a hub for the shaft. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Tasarım DosyasıSTLCC0 - Free
6

Print the valve flaps d

One flap, 50 x 100 mm with its hinge knuckle. Print two. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Tasarım DosyasıSTLCC0 - Free
7

Print the side panel

The removable segment, a panel with a flange that sits on a lip at its foot. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Tasarım DosyasıSTLCC0 - Free
8

Print the cap f

The cap, 168 mm across, a shallow cone with a 26 mm bore that slides on the shaft. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Tasarım DosyasıSTLCC0 - Free
9

Shaft, pins and handle

Cut a 25 mm stainless tube 600 mm long for the shaft e. Drill 6 mm holes across it 10 mm and 185 mm from its foot for the pins that hold the body's hub and the top's hub, and one 233 mm from its foot for stop g. Cut 6 mm stainless pins 44 mm long and 3 mm pins 64 mm long, file their ends smooth, and make a hardwood T handle 200 mm wide bored for the tube's top.

Bu adım için malzemeler:

Paslanmaz çelik boruPaslanmaz çelik boru1 adet
Paslanmaz çelik çubukPaslanmaz çelik çubuk2 adet
Sert Ağaç TahtasıSert Ağaç Tahtası1 adet
Ahşap TutkalıAhşap Tutkalı1 adet

Gerekli aletler:

Demir TesteresiDemir Testeresi
El TesteresiEl Testeresi
Kablosuz MatkapKablosuz Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Yassı matkap ucu takımıYassı matkap ucu takımı
Eğeler (El Eğesi)Eğeler (El Eğesi)
Zımpara KağıdıZımpara Kağıdı
Şerit MetreŞerit Metre
10

Assemble the dasher

Slide the body onto the shaft and pin its hub. Hang a flap over each port on a 3 mm pin through the lugs, and check it swings out freely and falls back shut. Press the top c into the body and pin its hub. Slide the cap f on above it and push the stop pin g through, so the cap can lift 20 mm. Set the side panel's foot on its lip and slide the 3 mm locking pin over its top. Put the handle on, and pass the shaft through a 28 mm hole in the bucket's lid.

Bu adım için malzemeler:

PETG filamentPETG filament1 adet
20 Litrelik Kova20 Litrelik Kova1 adet

Gerekli aletler:

FDM 3B yazıcıFDM 3B yazıcı
Kablosuz MatkapKablosuz Matkap
Yassı matkap ucu takımıYassı matkap ucu takımı
11

The build in 3D

FreeCAD model of this build, half the bucket and lid cut away: the octagonal dasher with its flaps swung open, the perforated top, the cap lifted to its stop, the shaft and handle. It was checked at three heights of the stroke with the flaps shut and open and the cap down and up.
Tasarım DosyasıBLENDCC0 - Free
12

Churn

Pour about 8 litres of heavy cream at about 15 °C into the bucket, checked with the thermometer, and put the lid on. Work the handle up and down about 100 mm, keeping the dasher's floor off the bucket's floor, and time it. When the butter has come, lift the dasher out, pull the panel's pin, take out the panel and scoop out the butter. Pour off the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.

Bu adım için malzemeler:

Yağlı kremaYağlı krema8 l
İri Deniz Tuzuİri Deniz Tuzu1 adet
SuSu1 adet

Gerekli aletler:

Takılı kalan problu termometreTakılı kalan problu termometre
KronometreKronometre
Dijital Mutfak TerazisiDijital Mutfak Terazisi
Büyük paslanmaz çelik karıştırma kâsesiBüyük paslanmaz çelik karıştırma kâsesi
13

Troubleshooting

Valve-and-cap dasher troubleshooting.

Flow

Loading...
14

History and honest limits

**Parker Wineman** of Loydsville, Belmont County, Ohio, US 24,898, 26 July 1859, "Churn-Dasher". He claimed the dasher with its perforated top, movable cap and hinged valves. He gives no sizes and says the valves may be arranged in various ways. Fig. 1 draws the dasher with flat sides, which we copy; our flaps hang over ports near the top as in Fig. 2. Every size is ours, and our printed build has not been churned with.

Malzemeler

9

Gerekli Aletler

13

Tasarım dosyaları

6

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...