Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО

Adjustable Bench Power Supply: Constant Voltage / Constant Current with Cross-Over Lamps (Gately, Forbro, US 3,303,411, 1967)
An all-transistor bench supply with two knobs: one sets the voltage, the other the current. It holds the set voltage until the load tries to draw more than the set current, then switches at once to holding the current, and back again, with no in-between state. Two lamps show which mode is in control.
Result: an adjustable constant-voltage / constant-current DC supply with mode lamps.
Source: J. R. Gately (Forbro Design), US 3,303,411 (1967). Unknown: all component values and ratings. Builds on the same inventor's 1966 current-limited supply. Picture: the patent drawing.
Просунутий
Unknown
Інструкції
1
1
Build the raw supplies
Build the raw supplies
In a case, wire the cord through a switch and fuse to two power transformers, each with rectifiers and a filter: one gives the main power to be regulated, the other the bias supplies, held steady by Zener diodes. Not given: the voltages. Ours: the case, switch and fuse.
Матеріали для цього кроку:
Алюмінієвий корпус1 штука
Гнучкий шнур із вилкою1 штука
Тумблер1 штука
Плавкий запобіжник1 штука
Знижувальний трансформатор2 штук
Діод6 rectifiers
Електролітичний конденсатор3 filters
Стабілітрон2 biasНеобхідні інструменти ({count})
Ручний дриль
Набір викруток2
2
Fit the pass transistor and current bridge
Fit the pass transistor and current bridge
Put a power transistor on a heat sink in series with the output: collector to the negative supply, emitter through a current-sensing resistor to the negative output terminal. Make the current bridge from the sensing resistor, a reference Zener, a reference resistor and the adjustable current-control resistor: the output current is proportional to its setting. A small trimming resistor sets the maximum current. Not given: the values.
Матеріали для цього кроку:
Потужний транзистор1 series pass
Радіатор1 штука
Стабілітрон1 current reference
Реостат1 current control
Опір1 sensing, reference, trim set
Клема-барашок2 output + and -Необхідні інструменти ({count})
Паяльник3
3
Build the voltage bridge
Build the voltage bridge
Make the voltage bridge from a reference Zener, a reference resistor, the adjustable voltage-control resistor and the load itself across the output. A small trimming resistor sets the maximum voltage. Add two resistors that feed the current bridge enough extra to cover the voltage bridge's own current and any voltmeter across the output, so low currents are still held exactly.
Матеріали для цього кроку:
Стабілітрон1 voltage reference
Реостат1 voltage control
Опір1 reference, trim, compensation setНеобхідні інструменти ({count})
Паяльник4
4
Build the amplifiers and cross-over
Build the amplifiers and cross-over
Give each bridge an error amplifier. Feed the two amplified errors to the bases of a pair of transistors sharing one emitter resistor: whichever base is the more negative takes control and cuts the other off, so the supply is always cleanly in voltage mode or current mode. Amplify the shared emitter signal through two more transistors to drive the pass transistor's base. Add an emitter-follower clamp on the bias line. Not given: the transistor types.
Матеріали для цього кроку:
Друкована плата1 штука
Набір транзисторів1 error amplifiers, cross-over pair, drivers, clamp
Опір1 набір
Потенціометр1 clamp divider
Дріт припою1 as neededНеобхідні інструменти ({count})
Паяльник5
5
Fit the mode lamps and use it
Fit the mode lamps and use it
From the cross-over pair, drive two lamp transistors, each lighting one lamp: one for voltage mode, one for current mode. In use, set the voltage and the current limit. With a light load the voltage lamp is lit and the voltage holds; if the load tries to draw more than the set current, the supply switches to holding the current and the current lamp lights.
Матеріали для цього кроку:
Набір транзисторів1 two lamp drivers
Ламповий патрон2 штук
Лампа розжарення2 штукНеобхідні інструменти ({count})
Набір викрутокМатеріали
19- 1 штукаЗаповнювач
- 1 штукаЗаповнювач
- Заповнювач
- 1 штукаЗаповнювач
- Заповнювач
- 6 rectifiersЗаповнювач
- 3 filtersЗаповнювач
- 1 voltage referenceЗаповнювач
- 1 series passЗаповнювач
- 1 штукаЗаповнювач
- 1 voltage controlЗаповнювач
- 1 набірЗаповнювач
- Заповнювач
- 1 штукаЗаповнювач
- 1 two lamp driversЗаповнювач
- Заповнювач
- 1 as neededЗаповнювач
- 2 штукЗаповнювач
- 2 штукЗаповнювач
За цим кресленням виготовляють
Пов'язані креслення
Ці креслення діляться знаннями — техніки, матеріали або принципи
CC0 Суспільне надбання
Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.
Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

