Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Screw-and-Nut Egg Beater: Slide a Nut Along a Spiral on the Shaft and the Wire Beater Spins Back and Forth
TheChef

Створено

TheChef

11. листопад 2026DK
4
0
0
0
0

Screw-and-Nut Egg Beater: Slide a Nut Along a Spiral on the Shaft and the Wire Beater Spins Back and Forth

Frederick Ashley of New York received US 28,047, dated 1 May 1860, for an egg beater. A shaft with a spiral thread wound round it ends in a cage of beating wires. Hold the handle in one hand and slide the nut up and down the thread with the other: the shaft spins one way, then the other, and the wires beat the eggs. He adds that it can churn cream to butter or stir ice cream as it freezes. The patent gives no sizes; every size here is ours.
Початківець
About 3 hours, plus printing

Інструкції

1

A push becomes a spin

Завантаження блокнота Jupyter…
2

A hand-worked egg beater, the year before

Parker pumps the eggs through a grate. Ashley spins a cage of wires through them.
3

Read US 28,047

"The lower end of the shaft A is placed in the dish or vessel containing the eggs to be beaten; the handle E is taken hold of by one hand of the operator, and the nut D by the other. The nut D is then moved up and down alternately, giving to the beating wires B a rapid motion forward and back, until the eggs are thoroughly “beat” or broken and mixed."
4

Print the nut D

Nut 32 mm across and 40 long, bored 8.8 mm, with a helical slot at 80 mm pitch for the 3 mm thread. PETG, 0.2 mm layers, 100 % infill.
Файл дизайнуSTLCC0 - Free
5

Print the wire hub

Hub 20 mm across and 15 long, bored 8.4 mm, with six holes for the wire bows. PETG, 0.2 mm layers, 100 % infill.
Файл дизайнуSTLCC0 - Free
6

Print the foot cap

Cap 16 mm across and 10 tall, bored 8.4 mm, 4 deep, with six holes for the wire bows' lower ends. PETG, 0.2 mm layers, 100 % infill.
Файл дизайнуSTLCC0 - Free
7

Shaft A and thread C

Cut 330 mm of 8 mm stainless rod and round its ends with the file. Wind 3 mm stainless wire tightly round it, two full turns spread evenly from 120 to 280 mm above its foot (80 mm a turn), and bend each end of the wire into a small hole drilled in the rod so it cannot slip.

Матеріали для цього кроку:

Пруток із нержавкої сталіПруток із нержавкої сталі1 штука
Дріт із нержавкої сталіДріт із нержавкої сталі1 штука

Необхідні інструменти ({count})

Ножівка по металуНожівка по металу
Напилки (ручний напилок)Напилки (ручний напилок)
Слюсарні лещатаСлюсарні лещата
КруглогубціКруглогубці
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
8

Beating wires B

Bend six bows of 1.6 mm stainless wire, each reaching 35 mm out from the shaft and 80 mm long. Push the hub onto the shaft 80 mm above its foot and the cap onto its foot, and set each bow's ends in the hub's and cap's holes, 60 degrees apart; pin the hub and cap to the rod each with a short piece of wire through a drilled hole.

Матеріали для цього кроку:

Дріт із нержавкої сталіДріт із нержавкої сталі1 штука
Філамент PETGФіламент PETG1 штука

Необхідні інструменти ({count})

3D-принтер FDM3D-принтер FDM
КруглогубціКруглогубці
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
9

Nut D, collar and handle E

Thread the nut onto the shaft from the top, turning it to follow the wire. Fit a shaft collar 300 mm above the foot, and a hardwood handle 30 mm across and 95 long bored 8.6 mm on the top above it, so the shaft turns freely in the handle.

Матеріали для цього кроку:

Shaft CollarShaft Collar1 штука
Шканти з твердої деревиниШканти з твердої деревини1 штука

Необхідні інструменти ({count})

Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Наждачний папірНаждачний папір
10

The build in 3D

FreeCAD model of this build: the shaft A with the wire thread C, the nut D on it, the collar and handle E, and the six bows of the beating wires B between the hub and the foot cap.
Файл дизайнуBLENDCC0 - Free
11

Beat eggs

Break four eggs into a bowl. Stand the beater's foot in them, hold the handle in one hand and slide the nut up and down the thread with the other, timing it, until the yolks and whites are evenly mixed.

Матеріали для цього кроку:

ЯйцеЯйце4 штук

Необхідні інструменти ({count})

Скляна чашаСкляна чаша
СекундомірСекундомір
12

Troubleshooting

Screw egg beater troubleshooting.

Flow

Loading...
13

History and honest limits

**Frederick Ashley** of New York, US 28,047, 1 May 1860, "Egg-Beater". He claimed the beating wires with the screw-threaded shaft and nut, and noted it could be applied to churning cream or freezing ice cream, or fixed to a churn with its beaters in two sections turning contrary ways. Every size here is ours, and our nut and hub are printed.

Матеріали

6

Необхідні інструменти

10

Файли дизайну

4

За цим кресленням виготовляють

Пов'язані креслення

Ці креслення діляться знаннями — техніки, матеріали або принципи

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...