Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Homemade Wood Lathe: Hardwood Bed, Sliding Headstock and Tailstock, Steel Spindle With Stepped Pulley (Boy Mechanic, 1915)
Woody

Створено

Woody

13. листопад 2026NO
7
0
0
0
0

Homemade Wood Lathe: Hardwood Bed, Sliding Headstock and Tailstock, Steel Spindle With Stepped Pulley (Boy Mechanic, 1915)

E. E. Hulgan's lathe from The Boy Mechanic, Book 2 (1915), "in which wood and light metal articles may be turned": a 5 ft bed of two 2 by 4 in hardwood rails, a headstock clamped by bolts with a 3/4 in steel spindle in brass bearings and a three-step pulley, a bolted hardwood tailstock with a screw-fed dead centre, a sliding tool rest, and a screw-on chuck. Driven from a countershaft or by foot.
Просунутий
About 1-2 weeks

Інструкції

1

His sizes, and the pulley speeds

Завантаження блокнота Jupyter…
2

Read The Boy Mechanic, Book 2

"A strong, substantial lathe in which wood and light metal articles may be turned can be made by carefully following the description below and the detailed drawings of the parts."
3

Make the bed

Cut two pieces of straight-grained, smooth 2 by 4 in hardwood, 5 ft long, and hold them apart at each end with blocks of wood 2 in wide (Fig. 9 shows 2 in rails with a 2 in gap). The bed can be longer or shorter.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини2 штук
Шурупи по деревуШурупи по дереву1 штука

Необхідні інструменти ({count})

Ручна пилкаРучна пилка
Ручний рубанокРучний рубанок
Ручний дрильРучний дриль
РулеткаРулетка
4

Build the headstock frame

Make the two hardwood end pieces to the shape of Figs. 1 and 2 (2 in thick, 2 in apart on an 8 in base, 7-1/2 in high, 6 in wide at the bottom) and screw them to the base. Nail a slider 1 in thick and 10 in long, just wide enough to slide between the bed rails, under the base, 2 in from its rear end. Bore two 1/2 in holes through base and slider and put two 1/2 in bolts through them and through another slide and board under the bed, so tightening the nuts clamps the headstock. Screw a half-round wedge-shaped brace inside the frame against the front end.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини1 штука
Болт із півкруглою головкоюБолт із півкруглою головкою2 штук
Шестигранна гайкаШестигранна гайка2 штук
Шурупи по деревуШурупи по дереву1 штука
ЦвяхиЦвяхи1 штука

Необхідні інструменти ({count})

Ручна пилкаРучна пилка
СтамескиСтамески
Коловорот із перкоюКоловорот із перкою
Ручний дрильРучний дриль
5

Make the spindle and bearings

Make the spindle of tool steel or steel tubing, 3/4 in in diameter and 14 in long, and cut a thread on one end. Rivet on a hardened steel collar, 1/4 by 1-1/2 in, to turn against another collar of the same size on the headstock; screw a third collar to the rear end piece and fix a collar with a removable pin on the spindle, fitted to turn easily with no end play. Drill brass tubing for the spindle as bearings and wedge them into the headstock 6 in above the bed, in line; drill small oil holes from the top.

Матеріали для цього кроку:

Пруток інструментальної сталіПруток інструментальної сталі1 штука
Сталева труба конструкційнаСталева труба конструкційна1 штука
Shaft CollarShaft Collar4 штук
Сталеві заклепкиСталеві заклепки1 штука
Латунна трубкаЛатунна трубка1 штука

Необхідні інструменти ({count})

Ножівка по металуНожівка по металу
Набір мітчиків і плашокНабір мітчиків і плашок
Ручний дрильРучний дриль
Напилки (ручний напилок)Напилки (ручний напилок)
Слюсарні лещатаСлюсарні лещата
МолотокМолоток
6

Fit the stepped pulley

Make the pulleys 2 in wide, with the diameters on the drawing: 6, 4-1/2 and 3 in. Fasten them to the spindle with a removable pin. (Turned hardwood is our choice of material; he does not say.)

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини1 штука

Необхідні інструменти ({count})

Ручна пилкаРучна пилка
Коловорот із перкоюКоловорот із перкою
Ручний дрильРучний дриль
7

Make the chuck and centres

For the chuck (Fig. 3), take shafting 1-1/2 in in diameter and 2-1/2 in long, drill a 1/2 in hole through its centre, ream and thread one end to fit the spindle, and fit a setscrew over the 1/2 in hole. Make a wood-turning centre, and other centres and drills, from 1/2 in tool steel.

Матеріали для цього кроку:

Круглий пруток з маловуглецевої сталіКруглий пруток з маловуглецевої сталі1 штука
Пруток інструментальної сталіПруток інструментальної сталі1 штука
Установчий гвинт із чашоподібним кінцемУстановчий гвинт із чашоподібним кінцем1 штука

Необхідні інструменти ({count})

Ножівка по металуНожівка по металу
Ручний дрильРучний дриль
РозверткаРозвертка
Набір мітчиків і плашокНабір мітчиків і плашок
Напилки (ручний напилок)Напилки (ручний напилок)
Слюсарні лещатаСлюсарні лещата
8

Build the tailstock

Build the tailstock (Figs. 4-6) of three pieces of hardwood 2 in thick and one 1 in thick, shaped as drawn, held together with four bolts 7-1/2 in long. Give it sliders and clamp it to the bed like the headstock, but with one bolt, and weld a handle to its nut for easy clamping. Drill a piece of tubing 2 in long for a 1/2 in dead centre and set it 1-1/2 in into the joint between the two upper pieces. Bore for a 1/2 in bolt to slide in the tube; chisel a recess behind the tube for a 1/2 in nut; turn a bolt 7 in long, threaded for 2 in, into nut and tube, and rivet a handle or wheel on its end. Make the centre of 1/2 in tool steel with a tapered point.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини2 штук
Болт із півкруглою головкоюБолт із півкруглою головкою5 штук
Шестигранна гайкаШестигранна гайка2 штук
Сталева труба конструкційнаСталева труба конструкційна1 штука
Пруток інструментальної сталіПруток інструментальної сталі1 штука
Сталеві заклепкиСталеві заклепки1 штука

Необхідні інструменти ({count})

Ручна пилкаРучна пилка
СтамескиСтамески
Коловорот із перкоюКоловорот із перкою
Ручний дрильРучний дриль
Вугільний горнВугільний горн
КовадлоКовадло
Ковальський молотКовальський молот
Напилки (ручний напилок)Напилки (ручний напилок)
9

Make the tool rest

The tool rest (Figs. 7-9) has a slide 3/4 by 3 by 13 in with a slot 1/2 by 6 in. Bolt the rest base on the slide so it can be adjusted, and screw the rest to the base. Raise or lower it with wedges between slide and base, and clamp it to the bed like the tailstock.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини1 штука
Болт із півкруглою головкоюБолт із півкруглою головкою1 штука
Шестигранна гайкаШестигранна гайка1 штука
Шурупи по деревуШурупи по дереву1 штука

Необхідні інструменти ({count})

Ручна пилкаРучна пилка
СтамескиСтамески
Коловорот із перкоюКоловорот із перкою
10

Troubleshooting

Wood lathe troubleshooting.

Flow

Loading...
11

History and honest limits

From "How to Make a Wood Lathe" by E. E. Hulgan, Marion, Ind., in **The Boy Mechanic, Book 2**, Popular Mechanics, 1915 (Project Gutenberg 44585; checked on the archive.org scan boymechanicbook200chic2, pp. 434-436). Part shapes come from his Figs. 1-9; he gives no pulley material and no countershaft or foot-drive details. The pulley material, tools and metric figures are ours.

Матеріали

12

Необхідні інструменти

15

За цим кресленням виготовляють

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...