Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Ice Boat: Crossed Timbers, Skate-Edged Runners, Bicycle-Fork Steering and a Gaff Sail (Boy Mechanic, 1915)
Woody

Створено

Woody

13. листопад 2026NO
6
0
0
0
0

Ice Boat: Crossed Timbers, Skate-Edged Runners, Bicycle-Fork Steering and a Gaff Sail (Boy Mechanic, 1915)

Robert K. Patterson's ice boat from The Boy Mechanic, Book 2 (1915): a 16 ft timber crossed by a 10-1/2 ft one and braced with wires, two front runners of band iron ground like a skate edge, and a rear steering runner clamped in a cut-down bicycle fork worked by a lever. His text and his drawing differ on the mast (about 12 ft against 14 ft); both are given.
Просунутий
About 1 week

Інструкції

1

Text against drawing

Завантаження блокнота Jupyter…
2

Read The Boy Mechanic, Book 2

"In constructing the ice boat, use two poles, or timbers, one 16 ft. and the other 10-1/2 ft. long, crossed at a point 2-1/2 ft. from one end of the longer timber. The crossed pieces are firmly braced with wires, as shown."
3

Cross and brace the frame

Cross the 10-1/2 ft timber over the 16 ft one, 2-1/2 ft from its front end, and fasten them firmly. Brace them with wires as in the drawing: from the bow to points on the cross timber, and from the cross timber back along the long one. The drawing puts the wire points 6 in and 1 ft 6 in from each end of the cross timber.

Матеріали для цього кроку:

Дерев'яна жердинаДерев'яна жердина2 штук
Болт із півкруглою головкоюБолт із півкруглою головкою1 штука
Сталевий дрітСталевий дріт1 штука

Необхідні інструменти ({count})

Ручна пилкаРучна пилка
Коловорот із перкоюКоловорот із перкою
РулеткаРулетка
ОлівецьОлівець
4

Make the front runners

Cut two band-iron strips 18 in long, 3 in wide and 1/8 in thick; grind one edge like the edge of a skate and round the ends. Bolt each to the side of a wood piece 18 in long, 6 in wide and 2 in thick, so the ground edge projects about 1 in. With a pole frame, bolt each runner block at right angles to a 12 in piece of wood shaped as drawn, the bolts running diagonally through its shouldered part; the pole end rests on this and is bolted down. With squared timbers, fasten the runners straight to them.

Матеріали для цього кроку:

Смуга з маловуглецевої сталіСмуга з маловуглецевої сталі1 штука
Дошка з твердої деревиниДошка з твердої деревини1 штука
Болт із півкруглою головкоюБолт із півкруглою головкою1 штука

Необхідні інструменти ({count})

Ножівка по металуНожівка по металу
Настільний точильний станокНастільний точильний станок
Слюсарні лещатаСлюсарні лещата
Ручний дрильРучний дриль
Ручна пилкаРучна пилка
5

Make the steering runner

Fasten the rear runner between two pieces of wood so its edge projects, and clamp it in a bicycle fork cut down to leave about 3 in of the blades. Bore a hole through the rear end of the long timber for the fork head. Fit a lever (5 ft on the drawing) to the top of the fork head: bore a hole through the lever end at a slight angle to fit the head, slot the end, bore across the width of the handle and put in a bolt as a clamp.

Матеріали для цього кроку:

Смуга з маловуглецевої сталіСмуга з маловуглецевої сталі1 штука
Дошка з твердої деревиниДошка з твердої деревини1 штука
Вилка велосипедаВилка велосипеда1 штука
Болт із півкруглою головкоюБолт із півкруглою головкою1 штука
Хвойний брусок (рейка)Хвойний брусок (рейка)1 штука

Необхідні інструменти ({count})

Ножівка по металуНожівка по металу
Настільний точильний станокНастільний точильний станок
Коловорот із перкоюКоловорот із перкою
Ручна пилкаРучна пилка
СтамескиСтамески
6

Step the mast and fit the seat

Cut a mortise in the long timber 15 in from the front end and set the mast in it; stay it with wires as drawn. His text says the mast should be about 12 ft; his drawing marks it 14 ft 0 in: choose one and keep the sail to suit. Fasten a board on two crosspieces mortised into the top of the long timber, as a seat for the driver (5 ft long on the drawing, ending 2 ft 3 in from the stern).

Матеріали для цього кроку:

Хвойний брусок (рейка)Хвойний брусок (рейка)1 штука
Сталевий дрітСталевий дріт1 штука
Соснова дошкаСоснова дошка1 штука
Шурупи по деревуШурупи по дереву1 штука

Необхідні інструменти ({count})

Ручна пилкаРучна пилка
СтамескиСтамески
Ручний рубанокРучний рубанок
РулеткаРулетка
7

Make and rig the sail

Make the sail of any good material to his drawing: luff (along the mast) 9 ft 0 in, head 4 ft 8 in, foot 11 ft 0 in, leech 12 ft 6 in. Hang the main boom, 11-1/2 ft long, and the upper spar on the mast "in the usual manner". The text also names a jib boom of about 6 ft, which the drawing does not show.

Матеріали для цього кроку:

ПарусинаПарусина1 штука
Хвойний брусок (рейка)Хвойний брусок (рейка)1 штука
Бавовняна линваБавовняна линва1 штука

Необхідні інструменти ({count})

НожиціНожиці
Ручна пилкаРучна пилка
РулеткаРулетка
8

Troubleshooting

Ice boat troubleshooting.

Flow

Loading...
9

History and honest limits

From "An Ice Boat and Catamaran" by Robert K. Patterson, in **The Boy Mechanic, Book 2**, Popular Mechanics, 1915 (Project Gutenberg 44585; checked on the archive.org scan boymechanicbook200chic2, pp. 27-28). His text and drawing differ on the mast (about 12 ft against 14 ft 0 in) and on the jib boom, which is in the text only; both are stated, not resolved. He gives no timber sections, wire size or sail cloth: those choices are ours, as are the tools and metric figures. The summer catamaran conversion is not made here.

Матеріали

11

Необхідні інструменти

11

За цим кресленням виготовляють

Пов'язані креслення

Ці креслення діляться знаннями — техніки, матеріали або принципи

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...